INSTALLATION, OPERATION AND MAINTENANCE MANUAL Warning Please read carefully before proceeding with installation. Failure to follow attached instructions or operating parameters may lead to the product’s failure. ****************************************************************************************** Save manual for future reference.
Thank you for your purchase of a state of the art Watts Premier Zero Waste Reverse Osmosis (RO) water treatment system. Water quality concerns are quickly becoming more of a focus for the public. Lately you may have heard about contaminants in the drinking water, such as arsenic, perchlorate, chromium, cryptosporidium or Giardia. There may also be some local water issues in your area such as high levels of lead, radium and copper.
** Before installation, please take a moment to fill out the warranty card on page 21-22. Thank you for your purchase of a Watts Zero Waste Reverse Osmosis system. With proper installation and maintenance, this system will provide you with high quality water for years to come. All of Watts water enhancement products are rigorously tested by independent laboratories for safety and reliability.
Operational Parameters Installation must comply with State and local plumbing regulations. This system is to be installed to treat cold water only. Operating Temperatures: Operating Pressure: pH Parameters: Iron: TDS (Total Dissolved Solids) Turbidity Maximum 100°F (37.8°C) Maximum 85 psi (6.0 kg/cm2) Maximum 11 Maximum 0.2 ppm < 1800 ppm < 5 NTU Minimum 40°F (4.4°C) Minimum 40 psi (2.80 kg/cm2) Minimum 2 Hardness: Recommended hardness not to exceed 10 grains per gallon, or 170ppm.
***IMPORTANT NOTICE*** Not recommended for use on homes equipped with tankless water heaters. Contact Watts Premier for specific details regarding this unit and tankless water heaters. System was tested in a laboratory setting utilizing a hot water heater of 40 gallons set at 120º F. Performance may vary if your heater is smaller than 40 gallons or set above 120º F, contact the manufacturer for additional details.
Installation of Faucet Step 6 Place the escutcheon chrome plate and the black rubber washer on the faucet shank. (Parts found in faucet parts bag). Step 7 Insert the faucet shank through the hole in sink and let it rest on the sink top. Step 8 From the underside of the sink, slide on the locating washer, lock washer and brass nut onto the shank. Check orientation of faucet then tighten brass nut securely.
Adapt-a-Valve Installation Water supply line to the system must be from the cold water supply line only. Hot water connection is used for rinse water return and must be connected for system to function correctly. * Washer Configuration for 3/8” (With Brass Fittings) * Insert White Washer Step 11 Hot (Return) Cold (Supply) Configuration for 1/2” (Without Brass Fittings) Turn off the cold and hot water supply to the faucet by turning the angle stop valve completely off.
Blue Tube Connection (From The RO Module To TANK) Step 17 Position tank in desired location. Stand it upright or lay it on its side (using the black plastic stand). Measure the blue tube (marked “TANK”) from the RO module to the tank and cut it to length leaving a straight, square edge. Insert the tube into the quick connect fitting on the tank ball valve. Make sure the tube is pushed in all the way to the tube stop.
6 Month System Maintenance - Filter Kit #560038 *Order filters by calling 1-800-752-5582 or buy online at www.wattspremier.com. Items needed: √ Stage 1 - Sediment Filter (part #: 104017) √ Stage 2 - Carbon Block Filter (part #: 101009-White End Caps) Note: The filter wrench pictured (Part # 164003) may be purchased from Watts Premier to aid with twisting off filter housings but is not required. Step 1 Close the ball valve on the RO storage tank and open the RO Faucet.
Annual Maintenance - Filter Kit #560032 Items needed: √ Stage 1 - Sediment Filter (part #: 104017) √ Stage 2 - Carbon Block Filter (part #: 101009-White end caps) √ Stage 4 - 10” Final Polishing filter (part # 560010) √ 1/2 Cup of hydrogen peroxide or common household bleach - not included in filter kit. Note: Sanitizing of unit is recommended. Step 1 Perform steps 1 through 5 in the Six Month System Maintenance (Page 9). Note: If not sanitizing the system skip to step 8.
Your reverse osmosis system contains replaceable treatment components that are critical for effective contaminant reduction. Periodic inspection and following proper system maintenance is critical for continued performance. Membrane Maintenance RO Membranes have a life expectancy between 2 and 5 years, depending on the incoming water conditions and the amount the RO system is used. This reverse osmosis membrane is critical for effective reduction of total dissolved solids (TDS).
Check Air Pressure in the Tank Important: Check air pressure only when tank is empty of water! Check air pressure in the storage tank when you notice a decrease in available water from the RO system. Air can be added with a bicycle pump using the schrader valve that is located on the lower side of the tank behind a blue plastic cap. Step 1 Turn off the incoming cold water supply to the RO at the adapt-a-valve clockwise until it stops.
Adjust Faucet If the faucet has developed a drip it can be corrected by following the steps outlined below. Step 1 Remove faucet Spout first. Position both thumbs on the back edge of the lever and push forward. Step 2 Lever will slide forward and completely off of the faucet base. Step 3 Small brass tee can be turned 1/2 turn, counterclockwise, to adjust the tension on the black lever. This adjustment may be necessary to stop slow drips from tip of faucet.
Performance Data Sheet ZRO-4 Zero Waste RO Watts Premier Inc. 8716 W Ludlow Drive Suite #1 Peoria, AZ 85381 480) 675-7995 wpmail@wattsind.com GENERAL USE CONDITIONS: 1. System to be used with municipal or well water sources treated and tested on regular basis to insure bacteriological safe quality. Do not use with water that is microbiologically unsafe or unknown quality without adequate disinfection before and after the system.
Arsenic Fact Sheet Arsenic (As) is a naturally occurring contaminant found in many ground waters. Arsenic in water has no color, taste or odor. It must be measured by an arsenic test kit or lab test. Public water utilities must have their water tested for arsenic. You can obtain the results from your water utility contained with in your consumer confidence report. If you have your own well, you will need to have the water evaluated.
Item # Part # Description Item # Part # Description 1 2 4 5 6 7 8 9 10 11 14 15 16 17 18 19 20 21 22 23 24 25 FAUCET-AG-CHROME VALVE-BALL-PLAS-ELB TANK PRESS 3 GAL WHITE TANK STAND CON-PL-1/4C X 1/4M GAC-IL-10” 1/4F TEE MALE RUN 1/4 X 1/4 M SWITCH PRESSURE 60 PSI TSO CLIP-DOUBLE-MEM TO IL VALVE-CHECK QUICK CON ELB-PL-1/4CX1/8M-90 O-RING SET FOR VESSEL MEM-TFM-25 GPD-DRY O-RING SET FOR VESSEL VESSEL-MEM-HOUSING-RES VALVE-CHECK-PLA-ELBOW1/4CX1/8M NUT- 8/32 STEE
Other Products from Watts Premier Watts Premier has other fine water filtration products and accessories to enhance your water and to compliment your existing RO System. Listed on the next several pages are only a few of the items we offer. Visit our web site at www.wattspremier.com or call our Customer Service Representatives at 1-800-752-5582 (inside USA) 1-480-675-7995 (outside USA) for more products. Watts Premier offers a filter change kit which includes all replacement filters needed.
Replacement Filter Kit Compatible with Watts Premier Zero Waste Reverse Osmosis system. These filters provide an extra level of filtration by allowing for more contact between the carbon media and your water. Includes a 10” Final in-line Filter, Sediment Filter and a Carbon Block Filter. Part No. 560032 *$24.
Removing chlorine from your shower Special Chlorgon & KDF media – More effective then carbon medias with hot water applications in the removal of the following. √ √ √ √ √ Iron oxide (rust water) Free Chlorine (CL-) Combined Chlorine (Sodium Hypochlorite) √ Dirt, sediment √ Odors Hydrogen Sulfide (Rotten egg smell) Plus, its pH balanced.
WARRANTY REGISTRATION Thank you for selecting Watts Premier for your water filtration needs. 4 Ways to Register 1. On-line at www.wattspremier.com Register your product on-line and receive a 5% discount on your next on-line order, Plus receive reduced shipping. 2. Call in your information 1-800-752-5582 Call and we will enter your information. 3. Fax in your information 623-866-5666 Fax this form directly to us. 4. Mail in the information. Please complete the form below.
WARRANTY REGISTRATION Please Fill out and keep for your Records First Name:_________________________ Last Name:____________________________ Address: ________________________________________ City: ____________________ State: _______________________________________ Zip Code: ___________________ Country: USA CANADA MEXICO OTHER ____________ Phone # ______-__________ -__________ Email Address: ______________________ Date of Purchase: ___________________ Date of Install: _______________________ Installe
SERVICE RECORD DATE OF PURCHASE / / DATE OF INSTALL / / Date of (6 mos.) (6 mos.) Maintenance 1st stage 2nd stage Sediment Carbon Block INSTALLED BY NAME: (1 yr.) Final Filter Carbon NOTES: 23 SERIAL NO. # (2-5 yrs.) TFM Memb.
Limited Warranty What your Warranty Covers: If any part of your WATTS PREMIER Zero Waste Reverse Osmosis System is defective in workmanship (excluding replaceable filters and membranes), return unit after obtaining a return authorization (see below), less tank, within 1 year of original retail purchase, WATTS PREMIER will repair or, at WATTS PREMIER’S option, replace the system at no charge.
