INSTALLATION, OPERATION AND MAINTENANCE MANUAL Warning Please read carefully before proceeding with installation. Your failure to follow any attached instructions or operating parameters may lead to the product’s failure. Save manual for future reference Model: ZRO-PURE Refer to enclosed warranty for operating parameters to ensure proper use with your water supply. Watts Premier, Inc. Phone: 800-752-5582 P/N 299086 8716 W Ludlow Drive Suite #1 www.wattspremier.
Thank you for your purchase of a state of the art Watts Premier Reverse Osmosis (RO) water treatment system. Water quality concerns are becoming more of a focus for the public. You may have heard about contaminants in the drinking water such as Arsenic, Perchlorate, Chromium, Cryptosporidium or Giardia. There may also be some local water issues such as high levels of Lead and Copper.
** Before installation, please take a moment to fill out the warranty card on page 21. Table of Contents Operational Parameters.................................................................................................................... 4 Contents of Reverse Osmosis System............................................................................................. 4 Installation & Startup Tools Recommended For Installation.............................................................................
Operational Parameters Installation must comply with State and local plumbing regulations. Do not use with water that is micro biologically unsafe or of unknown quality without adequate disinfection before or after the system. System is intended to be installed using the cold water supply only. Operating Temperatures: Operating Pressure: pH Parameters: Iron: TDS (Total Dissolved Solids) Turbidity Hardness Maximum 100°F (37.8°C) Maximum 100 psi (7.0 kg/cm2) Maximum 11 Maximum 0.
Plumbing Diagram and Parts List Transformer Item # Part # Description 1 2 3 4 5 6 7 8 9 10 11 12 13 RO4-PNP-11-50 (Head & 4 Filter Cartridges) FITTING-ELBOW-90-QC-1/4TX1/4I TANK-3 GALLON-METAL-WHITE ADAPT-A-VALVE KIT FAUCET-NAG-BN-MONITOR TANK-VALVE-BALL-ELB-1/4QCX1/4F TANK STAND 1/4” GREEN TUBING - 4FT ea. 1/4” BLUE TUBING - 4FT ea. 1/4” RED TUBING - 1FT ea.
Drill a Hole for the Reverse Osmosis Faucet Marble Counter-top We recommend contacting a qualified contractor for drilling a hole in a marble counter-top. Counter Top / Porcelain & Stainless Steel Sink Note: Most sinks are pre drilled with 1 ¼” diameter hole that you can use for your RO faucet. (If you are already using it for a sprayer or soap dispenser, see step 1) Porcelain sinks are extremely hard and can crack or chip easily. Use extreme caution when drilling.
Faucet Installation Step 5 Place the escutcheon chrome plate and the black rubber washer on the faucet shank. (Parts found in faucet parts bag). Step 6 Insert the faucet shank through the hole in sink and let it rest on the sink top. Step 7 From the underside of the sink, slide on the locating washer, lock washer and brass nut onto the shank. Check orientation of faucet then tighten brass nut securely.
Adapt-a-Valve Installation Water supply line to the system must be from the cold water supply line only. Hot water connection is used for rinse water return and must be connected for system to function correctly.
In the parts bag locate two 3/8” male stem adapters and insert them into the upper ports on the ESOV as pictured in the photos below. Green Tube Connection (From Adapt-a-Valve to Pump) Step 14 Insert the open end 1/4” green tube from the Adapt-a-Valve into the 1/4” open end of the booster pump quick connect union. Make sure the tube is pushed in all the way to the tube stop.
Tank Ball Valve Installation Step 18 Teflon tape must be applied in a clockwise direction. Wrap (7 to 12 turns) around the male pipe threads (MPT) on the stainless steel fitting on top of the tank. Thread the quick connect ball valve (supplied in the parts bag) onto the stainless steel connector on the tank. Note: Do not over-tighten plastic connections.
Congratulations! You have completed the installation of your new Reverse Osmosis system. Please Follow the Startup Instructions. Start up Instructions Warning: To prevent the possibility of electrical shock, clean up any water on cabinet floor and dry all water from outside of RO unit. Step 1 Turn on the incoming hot and cold water angle stop valves. Turn both of the adapt-a-valves on and check the system for leaks and tighten fittings as necessary.
Changing The Filter Cartridges Your RO module is equipped with valved heads which will automatically turn off the water supply to each filter when the filter is released, thus you do not need to turn off the incoming water supply at the Adapt-a-Valve. The RO faucet must be off when filters are replaced. To make the removal of the filter cartridges easier, the heads & cartridges may be swiveled up to 90 degrees as shown in the pictures below.
Annual Sanitization Note: Sanitization procedure must be performed before a filter change. Step 1 Turn off the water supply to your RO system, unplug transformer and open the RO faucet to drain the storage tank. Step 2 Disconnect the blue tube from the ball valve on the storage tank (see page 6 for quick connect fitting use instructions). Step 3 Using a clean eye dropper insert ½ teaspoon of hydrogen peroxide or common household bleach into the blue tube.
Check Air Pressure in the Tank Important: Check air pressure only when tank is empty of water! Check air pressure in the storage tank when you notice a decrease in available water from the RO system. Air can be added with a bicycle pump using the schrader valve that is located on the lower side of the tank behind a blue plastic cap. Step 2 Open the RO Faucet and allow water to drain from the tank until it is completely empty. SI Turn off the cold water supply to the RO and unplug transformer.
TROUBLE SHOOTING Problem Cause Solution 1. Low/Slow Production Low Water Pressure Crimps in tubing Clogged pre-filters Fouled membrane Make sure water supply is turned on and Adapta Valve is all the way open. Check tubing and straighten or replace as necessary. Replace pre-filters. Replace membrane. 2. Milky colored Water Air in system Air in the system is a normal occurrence with initial start up of the RO system.
TECHNICAL & WARRANTY INFORMATION Watts Premier Inc. 8716 W Ludlow Drive Suite #1 Peoria, AZ 85381 ZRO-Pure System conforms to Standard 58 for specific claims GENERAL USE CONDITIONS: 1. System to be used with municipal or well water sources treated and tested on regular basis to insure bacteriological safe quality. DO NOT use with water that is microbiologically unsafe or unknown quality without adequate disinfection before and after the system.
Arsenic Fact Sheet Arsenic (As) is a naturally occurring contaminant found in many ground waters. Arsenic in water has no color, taste or odor. It must be measured by an arsenic test kit or lab test. Public water utilities must have their water tested for arsenic. You can obtain the results from your water utility contained with in your consumer confidence report. If you have your own well, you will need to have the water evaluated.
Nitrate / Nitrite Test Instruction Page 18
Other Products from Premier Premier has other fine water filtration products and accessories to enhance your water and to compliment your existing RO System. Listed on the next several pages are only a few of the items we offer. Visit our web site at www.wattspremier.com or call our Customer Service Representatives at 1-800-752-5582 (inside USA) 1-480-675-7995 (outside USA) for more products. Premier sells a filter change kit which includes all replacement filters needed.
Removing chlorine from your shower Special Chlorgon & KDF media – More effective then carbon medias with hot water applications in the removal of the following. √ √ √ √ √ Iron oxide (rust water) Free Chlorine (CL-) Combined Chlorine (Sodium Hypochlorite) √ Dirt, sediment √ Odors Hydrogen Sulfide (Rotten egg smell) Plus, its pH balanced.
WARRANTY REGISTRATION Thank you for selecting Premier for your water filtration needs. 4 Ways to Register 1. On-line at www.wattspremier.com Register your product on-line and receive a 5% discount on your next on-line order, Plus receive reduced shipping. 2. Call in your information 1-800-752-5582 Call and we will enter your information. 3. Fax in your information 623-866-5666 Registering will insure you receive Watts FREE Fax this form directly to us. 4. Mail in the information.
WARRANTY REGISTRATION Please Fill out and keep for your Records First Name:_________________________ Last Name:____________________________ Address: ________________________________________ City: ____________________ State: _______________________________________ Zip Code: ___________________ Country: USA CANADA MEXICO OTHER ____________ Phone # ______-__________ -__________ Email Address: ______________________ Date of Purchase: ___________________ Date of Install: _______________________ Insta
Service Record Model Number:__________ Serial Number:___________ Date of Purchase:__________ Date of Install:___________ Installed by:_____________ Date Sediment Filter (6 months) Carbon Pre-Filter (6 months) Membrane (2-5 years) NOTES: Page 23 Carbon Post-Filter (12months)
Limited Warranty What your Warranty Covers: If any part of your Premier Reverse Osmosis System is defective in workmanship (excluding replaceable filters and membranes), return unit after obtaining a return authorization (see below), less tank, within 1 year of original retail purchase, Premier will repair or, at Premier’s option, replace the system at no charge. How to obtain Warranty Service: For warranty service, call 1-800-752-5582 for documentation and a return authorization number.
