User Manual

ManualsBrandsWave Wireless Networking ManualsElectronicsPoint to Point Spread Spectrum Transceiver

SC5800 User Manual

Object ID Group Object Type Access Description

1.3.6.1.4.1.1316.1.1.1.1.4.6

mdrmteScc2FullCnt† COUNTER read-only Indicates the total number of

times SCC2 was full to capacity

1.3.6.1.4.1.1316.1.1.1.1.4.7 mdrmteScc1UnderrunCnt† COUNTER read-only Indicates the total number of

times SCC1 ran out of BDs

1.3.6.1.4.1.1316.1.1.1.1.4.8

mdrmteScc2UnderrunCnt† COUNTER read-only Indicates the total number of

times SCC2 ran out of BDs

1.3.6.1.4.1.1316.1.1.1.1.4.9

mdrmteScc2RxBdAbortCnt† COUNTER read-only Indicates the total number of

times SCC2 received an

aborted frame

1.3.6.1.4.1.1316.1.1.1.1.4.10 mdrmteScc2RxBdNonOctCnt† COUNTER read-only Indicates the total number of

times SCC2 received a Non

octet aligned frame

1.3.6.1.4.1.1316.1.1.1.1.4.11 mdrmteScc2RxBdCrcCnt† COUNTER read-only Indicates the total number of

times SCC2 received

1.3.6.1.4.1.1316.1.1.1.1.5 mdrmteResetAllPerfData INTEGER write-only Reset all parameters associated

with Packet Error and G.826

measurements for the RF Link.

1.3.6.1.4.1.1316.1.1.1.2 mdrmteConfiguration

1.3.6.1.4.1.1316.1.1.1.2.1 MdrmtePayloadConf

1.3.6.1.4.1.1316.1.1.1.2.1.1 MdrmteDataRate INTEGER read-write Configure the tributary data

interface rate - either E1 or T1.

1.3.6.1.4.1.1316.1.1.1.2.1.2 mdrmteLineCodeType INTEGER read-write Defines the line code types for

the tributaries, either HDB3 or

AMI for E1 tributaries or B8ZS

or AMI for T1 tributaries.

1.3.6.1.4.1.1316.1.1.1.2.1.3 mdrmtePcTable SEQUENCE

1.3.6.1.4.1.1316.1.1.1.2.1.3.1 mdrmtePcEntry SYNTAX

1.3.6.1.4.1.1316.1.1.1.2.1.3.1.

mdrmtePcIndex INTEGER

1.3.6.1.4.1.1316.1.1.1.2.1.3.1.

mdrmtePcLabel DisplayString read-write E1/T1 Payload configuration

tributary label.

1.3.6.1.4.1.1316.1.1.1.2.1.3.1.

mdrmtePcActive INTEGER read-write Defines whether tributaries are

active or inactive.

1.3.6.1.4.1.1316.1.1.1.2.2 mdrmteRFLinkConf

1.3.6.1.4.1.1316.1.1.1.2.2.1 mdrmteTxPower INTEGER read-write Allows setup of the output power

available at the diplexer port of

the Outdoor Unit.

1.3.6.1.4.1.1316.1.1.1.2.2.2 mdrmteBandPlan INTEGER read-write The SC5800 Outdoor Units

operate in the 5.725 GHz to

5.850 GHz ISM frequency band.

The SC5800 has predefined

frequency channel plans

(termed A, B, C and D). Refer

to the User's manual for details

on defined frequencies.

1.3.6.1.4.1.1316.1.1.1.2.2.3 mdrmteTxFrequencyPlanD INTEGER read-write Frequency plan D allows

independent control of transmit

and receive frequencies. This

enables a very flexible

frequency plan and can be used

to overcome interference in the

5.8 GHz ISM band. The

frequencies that can be used in

the lower or upper sub-bands

can be selected in 1 MHz

increments. Performance