Consulting * Research * Training * Certification Testing Since 1981 FCC ID: PQS-DWM0001 Exhibit 9 User’s Manual February 2002 APREL Project No.
Dualwave M Wireless Modem User Manual
© Wavenet Technology Pty Ltd ACN 079 965 003 Publication No. DWMUSERD01 (First Draft 13 February 2002) Published January 2002 This publication is copyright and no part may be reproduced or copied without the prior consent of: Wavenet Technology Pty Ltd. 140 Burswood Rd Burswood Perth WA 6100 Australia Telephone: Facsimile: E-mail: Web Site: +61 8 9262 0200 +61 8 9355 5622 wavenet@wavenet.com.au www.wavenet.com.au This manual is intended to be used for the operation of Wavenet Technology equipment.
Dualwave M User Manual ________________________________________________________________Contents Contents Introduction...................................................................................................................5 Features ....................................................................................................................5 Compliance Statement ...........................................................................................6 Information for Your Safety.........
Introduction ______________________________________________________________Dualwave M User Manual Introduction The Dualwave M is a wireless modem developed for Personal Digital Assistants (PDAs), such as the Palm™ m125/m500/m505. It enables access to worldwide DataTAC wireless networks in the USA, Canada, Malaysia, Singapore, Hong Kong, Taiwan and Australia. The Dualwave M is available in 2 customer configurations.
Dualwave M User Manual ______________________________________________________________Introduction • Extended battery life (5 days standby, 14 hours communication time). • High sensitivity reception. • Indicator lights shows the status of the network coverage and battery condition. Compliance Statement This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to Part 15 of the FCC rules.
Introduction ______________________________________________________________Dualwave M User Manual and standards. The DUALWAVE M has been assessed at the worst case user conditions (zero separation distance). To maintain the optimum operational characteristics , no part of the human body should be in contact with the antenna during use. Safe Use Switch the Dualwave M off in areas where radio devices are forbidden, or when it may cause interference or danger.
Dualwave M User Manual ______________________________________________________________Introduction • The Dualwave M or Battery Charger has been dropped or damaged in any way. • The Dualwave M or Battery Charger does not operate normally by following the instructions contained in this manual. • The Dualwave M or Battery Charger exhibits a distinct change in performance. Failure to observe all these instructions will void the limited warranty.
Introduction ______________________________________________________________Dualwave M User Manual Dualwave M Data Comms cable Battery Charger The PC serial connector has 9 pins. Use a 25-pin to 9-pin adapter (not included), if your system has a 25-pin serial port. You should also have the CD-ROM which includes the Modem Tools software, and this User Manual. Exploring Your Dualwave M A picture of the Dualwave M is shown below.
Dualwave M User Manual ______________________________________________________________Introduction Release Button and Latch Connects and releases the PDA from the Dualwave M. On/Off Button Switches the Dualwave M on or off. The indicator descriptions are described on the following page.
Introduction ______________________________________________________________Dualwave M User Manual Online Indicator Online Indicator Off The Dualwave M is not connected or is out of range. Slow flashing green (once per sec) The Dualwave M is in range and has registered with the wireless network. Rapid flashing green (five times per sec) Access denied. The network is denying registration.
Dualwave M User Manual ___________________________________________________________ Getting Started Getting Started Before using your Dualwave M you must: • Connect the Dualwave M to your PDA • Fully charge the Dualwave M’s battery • Install the Modem Tools software on your computer and PDA Connecting Your Dualwave M to the PDA To connect the Dualwave M to your PDA, follow the steps below: 1. Slide the PDA into the Dualwave M so that the PDA ports are aligned. 2.
Getting Started____________________________________________________________Dualwave M User Manual Charging the Dualwave M’s Battery Your Dualwave M’s lithium battery is supplied discharged. For optimum performance, you should charge it fully before use. If during use, the Dualwave M’s On/Low battery indicator displays flashing red, the battery needs immediate recharging. The Battery Charger charges both the PDA and the modem. However, The Dualwave M’s battery powers only the modem, not the PDA.
Dualwave M User Manual ___________________________________________________________ Getting Started If the indicators on the battery charger are flashing red, indicating a fault, return the battery charger and Dualwave M to your vendor for servicing. When the batteries are fully charged, the battery charger stops charging until the batteries’ capacity falls below a certain value. The battery charger will then automatically start recharging the batteries again.
Getting Started____________________________________________________________Dualwave M User Manual connector is a 9-pin plug. If your computer has a 25-pin serial port you will need a 9-pin to 25-pin adapter. 4. Switch the PC on and insert the CD-ROM, which was supplied with your Dualwave M, into your CD-ROM drive. 5. Display the Palm Desktop screen by either: q Double-clicking the Palm desktop icon or, q Clicking from the PC’s task bar and selecting: Programs ⇒ Palm Desktop ⇒ Palm Desktop. 6. Click 7.
Dualwave M User Manual ___________________________________________________________ Getting Started 9. Select all of the files from the Modem Tools folder on the CDROM and click . The Install Tool screen is redisplayed with your selected files. Note: To select all of the files from the Modem Tools folder, click the first file and then press the Ctrl key and the A key together. 10. Click . The following message is displayed. 11.
Getting Started____________________________________________________________Dualwave M User Manual Removing Software From Your PDA To remove the software from your PDA, refer to the instructions in your PDA User manual. The typical procedure is shown below. 1. Tap the Applications icon on the main screen of your PDA. 2. Tap the Menu icon. 3. Tap App. 4. Tap Delete. 5. Tap the Dualwave M application. 6. Tap Delete. 7. Tap Yes. 8. Tap Done. To remove the software from your PC: 1.
Dualwave M User Manual ____________________________________________________Using Your Dualwave M Using Your Dualwave M Data Comms PC USB connector Data Comms Modem connector On/Low battery indicator On/Off button Online indicator Data Interface Port Ensure your Dualwave M is fully charged, the Modem Tools software has been installed and the unit is attached to the PDA before use, as described earlier. Press the On/Off button on the Dualwave M.
Using Your Dualwave M ____________________________________________________Dualwave M User Manual Modem Tools Application Modem Tools is a PDA application consisting of a single screen with four tabs. These four tabs are described in the following sub-sections. To access Modem Tools, tap the Modem Tools icon screen. By default the Info tab is displayed. from the main Info Tab This tab displays the following information about the Dualwave M attached to the PDA: This indicates the status of the battery.
Dualwave M User Manual ____________________________________________________Using Your Dualwave M Setup Tab This tab displays the following information: Power Tap to switch Dualwave M on or off. Vibrator By default the vibrator is on. This allows the Dualwave M to vibrate for three seconds after receipt of a radio message. Network Profile You may select a network profile from those stored in the modem. Change the setting by tapping and select from the drop-down menu.
Using Your Dualwave M ____________________________________________________Dualwave M User Manual Network Tab In order to make secure transactions via a gateway, a PDA requires a security certificate for the gateway. This tab allows you to request a security certificate for a specified gateway and also displays a list of the host addresses of all gateways for which a certificate has been loaded on to the PDA.
Dualwave M User Manual ____________________________________________________Using Your Dualwave M Wakeup Tab This tab displays a list of applications on your PDA that are registered for wakeup.
Using Your Dualwave M ____________________________________________________Dualwave M User Manual About Modem Tools This screen is displayed by tapping the icon, which appears in the top right hand corner of the Modem Tools screens. The following information is displayed: Version No. The version number of Modem Tools. WAP Stack Version The WAP stack used to build Modem Tools. VDD Version The Virtual Device Driver (VDD) installed on the PDA. Tap the OK button to return to the Main screen.
Dualwave M User Manual ____________________________________________________Using Your Dualwave M 4. Start the HotSync ® Manager if it is not already running, by either: q Double-clicking the HotSync® Manager icon from the PC’s desktop, or q From the PC’s task bar, click . From the start menu, select: Programs ⇒ Palm Desktop ⇒ HotSync Manager Select HotSync Manager Start Menu PC’s Task Bar Click the Start Button 5. Press the HotSync ® button on your PDA to start the HotSync ® process. 6.
Using Your Dualwave M ____________________________________________________Dualwave M User Manual Updating Firmware on Your Dualwave M Firmware is the resident software installed on your Dualwave M. For optimum performance ensure that you are using the latest firmware version. Follow the procedure below to check the version number of the firmware currently loaded on the Dualwave M. 1. Connect your PDA to the Dualwave M as described previously. 2. Switch your PDA on. 3.
Dualwave M User Manual ____________________________________________________Using Your Dualwave M 5. From the PC, double-click on the self-extracting file you have just downloaded to extract the contents. 6. Click the file: Loader.exe to display the following screen. 7. Select the appropriate modem port to which the Dualwave M is connected. 8.
Using Your Dualwave M ____________________________________________________Dualwave M User Manual 13. A flashing message is then displayed above the Download Application button, indicating that the modem has been updated. 14. Click to exit the program. Check that the firmware version has been updated. Follow the procedure below to check the version number of the firmware. 1. Tap the Modem Tools icon from the main screen. By default the Info tab is displayed. 2.
Dualwave M User Manual __________________________________________________________ Troubleshooting Troubleshooting If you encounter a problem with your Dualwave M or battery charger, do not call technical support until you have reviewed the following list of frequently asked questions. I’m getting no response from the Dualwave M. Make sure that the Dualwave M is switched on and is fully charged. The On/Low Battery indicator should display slow flashing green (once per second).
Troubleshooting___________________________________________________________Dualwave M User Manual I’m having difficulty sending and receiving messages. I’m not getting a very strong signal. I keep losing the signal. Check the indicators. They should both display slow flashing green (once per second) when connected with the network. On/Low Battery Indicator This should display slow flashing green to indicate that the battery is sufficiently charged.
Dualwave M User Manual __________________________________________________________ Troubleshooting Both indicators are flashing green every second but I’m still having difficulty connecting. Check the connection status by tapping to display the Modem Tools screen. on your PDA’s main screen By default, the Info tab is displayed. Check the Status to see whether the Dualwave M is in or out of range. The Status shows that the Dualwave M is out of range.
Troubleshooting___________________________________________________________Dualwave M User Manual The Online LED is flashing quickly and I cannot access the network. Your device has been denied access to the network. Contact your mobile network operator or supplier. The On/Low Battery indicator is flashing red and green simultaneously. Press the On/Off button to switch the unit off. Wait for about five seconds and press the On/Off button again to switch the unit back on.
Dualwave M User Manual _______________________________________________________Care & Maintenance Care & Maintenance Your Dualwave M is supplied maintenance free. However, periodically clean off the dirt and dust that may adhere to the exterior casing. Use the following procedures: 1. Disconnect the Battery Charger and cables from the Dualwave M. 2. Dampen a clean, soft cloth with water and wring the cloth well. 3. Use the well wrung cloth to gently remove dirt and dust.
Care & Maintenance _______________________________________________________Dualwave M User Manual Wavenet Technology 32
Dualwave M System Description _______________________________________________________Specifications Specifications Physical Properties Weight Approximately 150g Size (L x W x H) 127mm x 80mm x 12mm Communication Protocols Modem to radio network protocol MDC, RD-LAP 3.1, 3.2, 3.3 Modem to terminal (e.g. handheld) protocol NCL 1.
Care & Maintenance _______________________________________________________Dualwave M User Manual Ports Communications Serial Port RS-232 compatible serial port, operating speeds 9600 baud PDA Port RS 232 compatible serial port 9600 baud LED Indicators Power on/off and battery status Flashing green - Online Flashing red Rapid flashing red power on, battery charged low battery very low battery Flashing green - online Battery Lithium-ion battery (3.6V) 1300mA/hour 3.
