I.D. AL - NanoPlayer mkII - MP3 & Wav audio player - User manual NanoPlayer mkII Audio Player MP3 & Wav Firmware version 2.x USER MANUAL ® Waves System V 2.
I.D. AL - NanoPlayer mkII - MP3 & Wav audio player - User manual TABLE OF CONTENTS A - Safety instructions ............................................................................ P1 B - Product information ........................................................................... P2 1 - Product presentation ......................................................................... P4 2 - Functionnalities .................................................................................
I.D. AL - NanoPlayer mkII - MP3 & Wav audio player - User manual WARNING: DO NOT EXPOSE TO MOISTURE AND DUST ! Unplug the power cord before any intervention ! FOR YOUR SAFETY, PLEASE READ CAREFULLY THIS OPERATION MANUAL BEFORE USING YOUR PLAYER A. SAFETY INSTRUCTIONS A.1 CE marking The CE marking is on the ID plate, at the back of the product. It means this product complies with the low voltage CE directive, according the EN 55022 standard, and the EMC directive 61000-4-x. A.
I.D. AL - NanoPlayer mkII - MP3 & Wav audio player - User manual • When operating this appliance, observe all local rules and enforced regulations! The homologation shall be invalid if any modification or alteration is made on the appliance. Operating modified appliances may lead to a penal suit. In the interest of the safety of work, the manager and the operator will be responsible for respecting the instructions. • Retain all packing material in case the device must be shipped.
I.D. AL - NanoPlayer mkII - MP3 & Wav audio player - User manual A.6 - Conditions of use : • This product has been designed for indoor use only. • If the device has been exposed to drastic temperature fluctuation (e.g. after transportation), do not switch it on immediately. The arising condensation water might damage your device. Leave the device switched off until it has reached room temperature. • Do not shake the device. Avoid brute force when installing or operating the device.
I.D. AL - NanoPlayer mkII - MP3 & Wav audio player - User manual 1 - Product presentation The NanoPlayer mkII is an audio player which reads MP3 and WAV files stored on a SD/SDHC memory card. Playback can be automated to read files in loop or when triggered by the input contact. The NanoPlayer mkII is a versatile player designed for installations where broadcast of sounds, music, sound effects or commentaries are required such as museums, exhibitions, POS displays...
I.D. AL - NanoPlayer mkII - MP3 & Wav audio player - User manual 3 - Installation 1 2 8 1 - Amplified audio output 2 - Line level audio output 3 - Luminous indicator 11 4 - Power supply 5 - Infrared detector 10 9 6 - Input contact 7 - SD/SDHC card connector 8 - Volume level setting 9 - Input contact 12 10 - Volume level setting 11 - Option (Serial link) 12 - Option S/PDIF 7 6 5 4 3 Memory card: choose a good quality card of a minimum size of 64Mo - New cards are usually formatted in «FAT».
I.D. AL - NanoPlayer mkII - MP3 & Wav audio player - User manual 3.1 - Connections Speakers Speakers L- / L+ R+ / RAmplifier Extension connector : - Volume level setting - Input contact - Power supply output - Optionnal serial link Audio product with S/PDIF input Power supply 12v Internal input schematic ® Waves System -6- V 2.
I.D. AL - NanoPlayer mkII - MP3 & Wav audio player - User manual 1 - Speaker Output: The NanoPlayer mkII includes a built-in amplifier. The board can therefore be connected directly onto speakers. Connect the speaker wires onto the output of each of the 2 channels. Caution: Never connect outputs between themselves, do not create short-circuits and do not use speakers with lower impedance than specified in the player specification.
I.D. AL - NanoPlayer mkII - MP3 & Wav audio player - User manual 5 - Infrared: The NanoPlayer mkII can be controlled with a infrared remote handset (not supplied with the OEM board - available separately). ID-AL remote control handset 6 - Input on dry contact: Connect a push button, presence detector, smoke, heat, light or pressure sensor ... relay output, or any type of contact to trigger the player when happening of an event. Create a brief contact between «SW» input and the ground G.
I.D. AL - NanoPlayer mkII - MP3 & Wav audio player - User manual 12 - S/PDIF connector: To provide a digital audio S/PDIF output. Power supply out 3,3v (100mA maxi) 0V 0V S/PDIF output 14 - Amplifier: NanoPlayer mkII uses a digital «Class D» amplifier. In normal use, the heat is small. However, for a long time use at high volume output or in a closed box, we suggest to stick a small cooling device. You can use the reference ICKSMDF10 / Fisher Electronik. ® Waves System -9- V 2.
I.D. AL - NanoPlayer mkII - MP3 & Wav audio player - User manual 4 - Operating the player and naming of files The NanoPlayer mkII reads files and playback instructions stored on the SD/SDHC memory card. No extra software is required to configure the player. Playback options are provided by the way the files are named and organized in the directories.
I.D. AL - NanoPlayer mkII - MP3 & Wav audio player - User manual ● The 2nd digit is a letter which defines the playback mode of the folder Folder 0 - «0xx» - has 2 playback modes Folder 1 «1xx» has the same 2 + 2 additional playback modes For the default folder (read on powering on) «0xx»: xRx : R for random mode (RND) xSx : S for sort mode, i.e. playback in a defined order (SORT) - «R» selects random playback of the files included in the folder.
I.D. AL - NanoPlayer mkII - MP3 & Wav audio player - User manual ● The 3rd digit is a figure which defines the mode for triggering files For folder «0xx» the 3rd digit define the mode 0 or 1. Trigger folder «1xx» or next file in folder «0xx» For folder «1xx» the 3rd digit define the mode for triggering files (activation mode) For the default folder (read on powering on) «0xx»: Mode 0 : An input contact play the files into folder «1xx» 0x0 -> The last «0» define mode 0 : A contact play folder «1xx».
I.D. AL - NanoPlayer mkII - MP3 & Wav audio player - User manual 4.2 Organization of audio files included in the folders As for folders, file names affect playback pattern. ● In random mode, naming of files is free. Only the extension is meaningful: name.mp3 for MP3 files or name.wav for WAVE files. ● In sequential mode, i.e. in sequence order playback mode, the first characters of file names must be 3 figures which define the sequence number of the file and therefore its playback order. Example : 001.
I.D. AL - NanoPlayer mkII - MP3 & Wav audio player - User manual 5 - Infrared remote control The NanoPlayer mkII includes an infrared sensor on the front of the board and can therefore be operated with a IR remote control. An optional ID-AL infrared remote control handsed is available.
I.D.
I.D. AL - NanoPlayer mkII - MP3 & Wav audio player - User manual http://www .id-al.com http://www.id-al.com http://www .wsystem.com http://www.wsystem.com ® Waves System V 2.