User Manual

ManualsBrandsWaveshare ManualsMicrocontrollersOpen103Z Standard STM32F1 Development Board

www.waveshare.com Open103Z User Manual

Open103Z User Manual

Contents

Preparation ........................................................................................................................................................ 2

8BitIO-Pushbutton ............................................................................................................................................. 2

ADC+DMA .......................................................................................................................................................... 3

CAN-LoopBack .................................................................................................................................................. 4

DAC .................................................................................................................................................................... 5

DS18B20+ .......................................................................................................................................................... 6

GPIO_Key_LED ................................................................................................................................................. 7

I2C ...................................................................................................................................................................... 8

LCD-HY32D_FSMC ............................................................................................................................................ 9

Nand Flash ....................................................................................................................................................... 10

NorFlash .......................................................................................................................................................... 11

PS2 ................................................................................................................................................................... 13

RTC .................................................................................................................................................................. 14

SD_FatFS ......................................................................................................................................................... 15

SDIO ................................................................................................................................................................. 16

SPI .................................................................................................................................................................... 17

SRAM ............................................................................................................................................................... 18

TouchPanel ...................................................................................................................................................... 19

UcosII2.91+UCGUI3.90A.................................................................................................................................. 20

USARTx_pritf ................................................................................................................................................... 20

VS1003B MP3 Board ....................................................................................................................................... 21

USB FS Example ............................................................................................................................................. 22

SL811 USB Board ............................................................................................................................................ 23

ENC28J60 Ethernet Board .............................................................................................................................. 25

Summary of content (26 pages)

PAGE 1
www.waveshare.com Open103Z User Manual Open103Z User Manual Contents Preparation ........................................................................................................................................................ 2 8BitIO-Pushbutton............................................................................................................................................. 2 ADC+DMA .........................................................................................................
PAGE 2
www.waveshare.com Open103Z Testing Guide Preparation Basic settings of the test ·Programming Interface: SWD ·Serial port settings: Select a proper COM port, and configure as follows:  Baud rate : 115200;  Data bits : 8;  Stop bits : 1;  Parity bits : None;  Flow control : None ·Power supply: 5V power supply is required.
PAGE 3
www.waveshare.com Open103Z Testing Guide Operation and Result Push the button, then the 4 LEDs will keep changing accordingly. ADC+DMA Overview ADC analog voltage acquisition ADC Hardware Connection ·Connect the serial port converter to the board via USART1 interface. ·Connect the Analog Test Board to the board via SPI1 interface.
PAGE 4
www.waveshare.com Open103Z Testing Guide Operation and Result Launch the serial debugging assistant, and configure it as described in chapter "Preparation". Info/message will be displayed on the serial debugging assistant as adjusting the resistor on the module. CAN-LoopBack Overview CAN-LoopBack Demo. Hardware Connection ·Connect a serial port converter to the board via USART1 interface.
PAGE 5
www.waveshare.com Open103Z Testing Guide Operation and Result Launch the serial debugging assistant, and configure it as described in chapter "Preparation". Info/message will be displayed on the serial debugging assistant. DAC Overview DAC output demo Hardware Connection ·Connect the Analog Test Board to the board via SPI1 interface.
PAGE 6
www.waveshare.com Open103Z Testing Guide ·Connect the 5V pin headers on both the main board and the Analog Test Board by jumper wire. As shown in the figure below: Operation and Result There will be a sound of triangular wave from the Analog Test Board. DS18B20+ Overview DS18B20+ temperature measurement demo Hardware Connection ·Insert the DS18B20+ to the ONE-WIRE Interface. ·Connect the serial port converter to the board via USART1 interface.
PAGE 7
www.waveshare.com Open103Z Testing Guide Operation and Result Launch the serial debugging assistant, and configure it as described in chapter "Preparation". Info/message will be displayed on the serial debugging assistant. GPIO_Key_LED Overview LED, Push button and Joystick demo Hardware Connection ·Short the LED jumpers on the board.
PAGE 8
www.waveshare.com Open103Z Testing Guide Operation and Result Push the button or joystick; the LED status will keep changing accordingly. I2C Overview I2C EEPROM demo Hardware Connection ·Connect the serial port converter to the board via USART1 interface. ·Connect the AT24CXX EEPROM Board to the board via I2Cx interface.
PAGE 9
www.waveshare.com Open103Z Testing Guide Operation and Result Launch the serial debugging assistant, and configure it as described in chapter "Preparation". Info/message will be displayed on the serial debugging assistant. LCD-HY32D_FSMC Overview LCD display demo Hardware Connection ·Connect the 3.2inch 320x240 Touch LCD (A) to the board via LCD Interface.
PAGE 10
www.waveshare.com Open103Z Testing Guide Operation and Result Information will be displayed on the LCD Nand Flash Overview Nand Flash demo Hardware Connection ·Connect the NandFlash Board (A) to the board via 8BIT FSMC interface. ·Connect the serial port converter to the board via USART1 interface.
PAGE 11
www.waveshare.com Open103Z Testing Guide Operation and Result Launch the serial debugging assistant, and configure it as described in chapter "Preparation". Info/message will be displayed on the serial debugging assistant.
PAGE 12
www.waveshare.com Open103Z Testing Guide Hardware Connection ·Connect the NorFlash Board (A) to the board via FSMC interface. ·Connect the serial port converter to the board via USART1 interface. As shown in the figure below: Operation and Result Launch the serial debugging assistant, and configure it as described in chapter "Preparation". Info/message will be displayed on the serial debugging assistant.
PAGE 13
www.waveshare.com Open103Z Testing Guide PS2 Overview PS2 keyboard demo Hardware Connection ·Connect the PS2 keyboard to the board via PS2 interface. ·Connect the serial port converter to the board via USART1 interface. As shown in the figure below: Operation and Result Launch the serial debugging assistant, and configure it as described in chapter "Preparation". Press any keys on the keyboard, the corresponding key value will be displayed on the serial debugging assistant.
PAGE 14
www.waveshare.com Open103Z Testing Guide RTC Overview RTC demo Hardware Connection ·Connect the serial port converter to the board via USART1 interface. As shown in the figure below: Operation and Result Launch the serial debugging assistant, and configure it as described in chapter "Preparation". Follow the tips and input data, Info/message will be displayed on the serial debugging assistant.
PAGE 15
www.waveshare.com Open103Z Testing Guide SD_FatFS Overview SDIO interface+ FatFS demo Hardware Connection ·Connect the Micro SD Storage Board (with SD card) to the board via SDIO interface. ·Connect a serial port converter to the board via USART1 interface. As shown in the figure below: Operation and Result Launch the serial debugging assistant, and configure it as described in chapter "Preparation". Info/message will be displayed on the serial debugging assistant.
PAGE 16
www.waveshare.com Open103Z Testing Guide SDIO Overview SDIO interface demo Hardware Connection ·Connect the Micro SD Storage Board (with SD card) to the board via SDIO interface. ·Connect a serial port converter to the board via USART1 interface. As shown in the figure below: Operation and Result Launch the serial debugging assistant, and configure it as described in chapter "Preparation". Info/message will be displayed on the serial debugging assistant.
PAGE 17
www.waveshare.com Open103Z Testing Guide SPI Overview SPI Flash demo Hardware Connection ·Connect the serial port converter to the board via USART1 interface. ·Connect the AT45DBXX DataFlash Board to the board via SPIx interface. As shown in the figure below: Operation and Result Launch the serial debugging assistant, and configure it as described in chapter "Preparation". Info/message will be displayed on the Serial debugging assistant.
PAGE 18
www.waveshare.com Open103Z Testing Guide SRAM Overview SRAM demo Hardware Connection ·Connect the IS62WV12816BLL SRAM Board to the board via FSMC interface. ·Connect the serial port converter to the board via USART1 interface. As shown in the figure below: Operation and Result Launch the serial debugging assistant, and configure it as described in chapter "Preparation". Info/message will be displayed on the Serial debugging assistant.
PAGE 19
www.waveshare.com Open103Z Testing Guide TouchPanel Overview LCD touch screen demo Hardware Connection ·Connect the 3.2inch 320x240 Touch LCD (A) to the board via LCD interface. As shown in the figure below: Operation and Result LCD touch screen function works, and allows writing and drawing on the LCD.
PAGE 20
www.waveshare.com Open103Z Testing Guide UcosII2.91+UCGUI3.90A Overview UcosII2.91+UCGUI3.90A demo Hardware Connection ·Connect the 3.2inch 320x240 Touch LCD (A) to the board via LCD Interface. As shown in the figure below: Operation and Result Launch the serial debugging assistant, and configure it as described in chapter "Preparation". Info/message will be displayed on the uCOSView-V310G and LCD.
PAGE 21
www.waveshare.com Open103Z Testing Guide Hardware Connection ·Connect the serial port converter to the board via USART1. As shown in the figure below: Operation and Result Launch the serial debugging assistant, and configure it as described in chapter "Preparation". Info/message will be displayed on the Serial debugging assistant.
PAGE 22
www.waveshare.com Open103Z Testing Guide Hardware Connection ·Connect VS1003B MP3 Board to the board via SPI interface. As shown in the figure below: Operation and Result ·Insert the headphone to the Line Out port. ·Connect the PC audio port and the VS1003B MP3 Board Line In port by audio cable.
PAGE 23
www.waveshare.com Open103Z Testing Guide Hardware Connection ·Connect the board to the PC via USB cable. ·Short the Joystick, LED jumpers. As shown in the figure below: Operation and Result (1) USB-Joystick Mouse: JOYSTICK can be used for simulating the mouse and controlling movement of the computer and mouse. (2) USB-Mass Storage-MCU Flash: MCU flash will be identified as USB flash drive in PC.
PAGE 24
www.waveshare.com Open103Z Testing Guide Hardware Connection ·Connect the 3.2inch 320x240 Touch LCD (A) to the board via LCD interface. ·Connect the SL811 USB Board to the board via 8BIT FSMC interface. ·Connect the mouse to the SL811 USB Board USB connector, and connect USB VCC to 5V as shown in the figure below: Operation and Result The LCD will display the mouse current status.
PAGE 25
www.waveshare.com Open103Z Testing Guide ENC28J60 Ethernet Board Overview ENC28J60 demo PC IP Setting Configure the local connection of PC as follows: -- IP add: 192.168.0.11 -- NETMASK_ADDR: 255.255.255.0 -- GW_ADDR:192.168.0.1 Hardware Connection ·Connect ENC28J60 Ethernet Board to the board via SPI interface, and then connect it to PC via straight-through Ethernet cable. As shown in the figure below: Operation and Result Enter 192.168.0.
PAGE 26
www.waveshare.