USER GUIDE|MANUAL|SAFETY V2.0 2022.
Contents Read and understand this user manual and all safety instructions before using this product. I Disclaimer II Overview �.� Brief Introduction �.� Safety Guidelines III Waydoo Subnado �.� Product Diagram �.� Product Specifications IV Charging �.� How to charge Subnado �.� Reverse charging function V Assembly Steps VI How to use VII Product Specifications VIII Error and Tone Indication �.� Error indication and solution �.� Tone Indication XI Maintenance �.� Cleaning after use �.
I Disclaimer Please fully read this product manual and related warnings and Safety Guidelines carefully before use. Please fully understand your legal rights, responsibilities, and safety instructions. This product is an underwater scooter. Improper use may cause the risk of severe injury or death. USE THIS PRODUCT AT YOUR OWN RISK. Users must understand and accept the inherent risks of using this product. Any misuse of this product may cause personal injury or property/product damage.
II Overview �.� Brief Introduction Established in ����, Shenzhen Waydoo Intelligence Technology Co.,Ltd. is a high-tech enterprise integrating research and development, production, and sales of water sports high-tech products. With the experience of the R&D team and technological expertise, Waydoo launched the first underwater scooter, Waydoo Subnado, through several technical innovations.
III Waydoo Subnado �.� Product Diagram Rear cover Handle Bracket Propeller Power switch Trigger Main unit Waterproof cover �.� Product Feature ◆Two-speed thrust: The high and low gear provides two-speed thrust options. Users can switch to the high or low gear by pressing the trigger twice quickly. Users will hear one beep if they successfully switch to low gear or two beeps if they switch to the high gear. ◆Super gear: Quickly press the trigger three times.
◆USB-C Fast Charging: Use a standard USB-C charger (PD�.�, QC�.�, QC�.�, BC�.�, and other charging protocols.) to charge Subnado. The maximum charging power input is ���W. (Note: It needs to be supported by the charger and use of an ���W capable charging cable to reach the maximum charging power). ◆Reverse charging: Subnado can be used as a power source to charge other devices. Reverse charging supports standard protocols such as PD�.�, PPS, QC�.�, QC�.�, and BC�.�.
�.� Waterproof cover installed securely in place. �. The waterproof cover keeps water from entering the USB-C port. Improper installation or lack of grease may cause water to enter the USB-C port, and damage to the USB-C port. It is critical to ensure that the USB-C port is free of water. The grease acts as a seal for the waterproof cover. Be sure to install the waterproof cover securely in place to prevent seawater from leaking into the USB-C port and damaging the device. �.�.
Controller port waterproof cover Controller connector Please check the controller port for grease and O-ring damage. The damaged O-ring must be replaced before use. Apply grease to the controller connector. Grease the waterproof cover. The controller connector is designed to prevent water from entering the connector port. Moisture presenting in the connector port may cause: �. The motor to run nonstop when the Subnado is switched on. �.
�. Hold the handgrip and place the Arm mount on the outside of the forearm.Wrap the strap around the forearm �-� times, depending on the arm circumference. �. Fasten the gourd buckle on one end of the strap. �. According to the forearm circumference, wrap it �-� times and finally fix it with nylon tape. �. Install the main unit to the Arm mount through the quick release part.
Fix the Subnado leg mount to the outside of the leg. Install the main unit to the leg mount through the quick release part. Note:Please use the specially designed straps for the leg mount. Subnado Leg Mount Fasten the belt around the waist. Pass the straps on both sides of the waist belt through the holes above the leg mount, and then fix them with nylon straps.
Board Mount Installation: �.Please confirm that the board surface is clean and even before installation. Please wipe off any dirt or dust, and keep the surface dry. �.Peel off the protective liner on the board mount’ s adhesive pads, attach the mount to the board and firmly press the pads to ensure a tight bond. �.Let the adhesive cure for half an hour after installation to get a strong bond. �.Install the Subnado to the board mount through the quick-release clamp.
Install the handle bracket on the main unit. Turn the waterproof cover counterclockwise to the illustrated position. Install the wired thumb controller to the corresponding port. Installation complete. Tighten the waterproof cover clockwise. DO NOT use twin handle bracket with a single Subnado. Note: Please install the wired thumb controller in a dry environment. Please dry the port before installation if it is wet.
A wrist strap is recommended to prevent dropping the product by accident. Please use the first screw hole to secure the wrist strap. Warning: To prevent entanglement, please DO NOT use the two rear screw holes to secure the wrist strap. Installation steps for Subnado Water Cannon Kit. hose Nozzle base shell Subnado Water Cannon Kit �. Install the shell on the rear cover. Press down on the nozzle base to connect the hose to the shell. �. Unscrew main unit's rear cover clockwise �.
(�) If the users' fingers are relatively slender and are worried about injury during use, they can install the finger safe-guard. The following are the installation steps: (Note: Using a finger safe-guard will increase water resistance, resulting in increased power consumption which affects efficiency and reduces battery life and thrust) a. Please turn off the main unit first. Unscrew the rear cover of the main unit clockwise, remove the O-ring, and take off the propeller.
c. Put the finger safe-guard into the groove, press each end of the finger safe-guard into place, and make sure the end of the finger safe-guard is engaged with the notch in the groove (as shown in the figure) end d. Check the grease condition. In case the grease is insufficient, please add grease to the optimal amount. Then install the propeller with the pin is properly seated. e. After installing the O-ring, check the grease condition.
VI How to use This product requires users to be fully familiar with it before use, and users need to have basic knowledge before operating. Waydoo hereby strongly recommends that users read and follow each of the steps before use. �. Check if the waterproof cover is in place (refer to IV - Charging). �. Check if there is water in the plug, as well as check the grease condition (refer to the installation steps). �. Press the trigger to confirm normal function, and to check if the throttle control is good. �.
Figure � LED Light Capacity <�% �%-��% ��%-��% ��%-��.�% ��.�%-��% ��%-��.�% ��.�%-��% ��%-��.�% ��.�-���% Note: All of the above and below half-segment LED lights represent the flashing LED lights. VII Product specifications Product weight About �.�kg Maximum speed �.
VIII Error and Tone Indication LED � on the left of the charging port LED � on the right of the charging port �.� Error indication and solution Fault Indicator 17 Fault Solution Cell undertemperature Place the main unit in an environment of ��-�� degrees Celsius. Wait for the main unit temperature to rise to a suitable temperature, and the charging will start automatically. Cell overtemperature �. Stop charging �.
Fault Indicator Fault Battery Over-discharge Solution Please contact Waydoo support team. Motor Communication Update the firmware Failure PD Communication Failure MCU Overheat Charging Overheat �. Use recommended chargers that meet the published charging protocol requirements, such as a charger that supports PD/QC protocol. �. If the problem cannot be solved with a new charger, please contact Waydoo support team. �. Please shut down the device immediately. �.
�.
XI Maintenance Improper maintenance, disassembling and repair may cause damage to this product, personal injury, including electric shock, and be deemed a waiver by the purchaser, owner and user of the product warranty as noted in the Warranty Terms and Limitation of Liability sections of this manual. �.� Cleaning after use After each product use, please follow the guidelines to rinse the product to maintain the corrosion resistance and extend the product life.
Warranty Terms Limited Warranty Under this limited warranty policy, Waydoo warrants the original buyer for the warranty period that the product will be free from material and workmanship defects under normal use in accordance with Waydoo Subnado's published product materials. The warranty period is ONE (�) YEAR for specific parts starting from the date you received products.
What Should I Do Before Getting Warranty Service? When reaching out to Waydoo, please provide a detailed description of the product problem. Waydoo technical support representative will attempt to diagnose and resolve the problem via e-mail or remote assistance. If the problem persists, you may need to send the product back to Waydoo or an authorized Waydoo service center for further testing. Waydoo will arrange for repair or replacement under the limited warranty.
What is NOT Covered by This After-Sales Policy? This policy does not cover the following: × Parts not specified in the APPENDIX *. × Changes in appearance or damages caused by normal wear and tear, color change, etc. × Damage caused by crash, physical impact, or fire resulting from non-manufacturing factors, including but not limited to, user error. × Damage caused by unauthorized modification, or disassembly not in accordance with official instructions or manuals.
Disclaimer √ Limited Warranty policies and related costs may vary with respect to the local laws or the corresponding Waydoo service availability in different countries/regions where Waydoo product is purchased. √ You may need to send the faulty product(s) back to Waydoo or a Waydoo-authorized service center. Waydoo will examine the returned product(s) to identify the problem and the responsibility upon receipt of the product(s).
√ Before sending your product for repair, please remove any attached customized decorations and items. Waydoo will not be responsible for any damage or loss that may occur to these customized decorations and attachments. √ To guarantee your legal rights, please check whether your product is intact (check whether any damage has occurred to your product during transportation) when signing for its delivery.
Your Other Rights This Limited Warranty provides you with extra and specific legal rights. You may have other rights according to the applicable laws of your state or jurisdiction. You may also have other rights under a written agreement with Waydoo. Nothing in this Limited Warranty affects your statutory rights, including rights of consumers under laws or regulations governing the sale of consumer products that cannot be waived or limited by agreement.
Waydoo Technical Support This guide may be updated without notice. Check the official Waydoo website for the latest version www.waydootech.
