Product Manual

ManualsBrandsWayne ManualsCondensate Removal Pumps120-Volt 1/2 HP Sewage Pump

SPECIFICATIONS

POWER SUPPLY

REQUIREMENTS 120 V, 60 Hz

MOTOR Single Phase, Dielectric Oil Filled

HORSEPOWER

1/2 HP............ Sewage

(RPP50, SEL50, WCS50T)

Efuent

(EFL50)

CIRCUIT REQUIREMENTS 15 A (minimum)

DIMENSIONS

14 in. high x 12 in. base

(RPP50)

13-1/2 in. high x 11 in. base

(SEL50, EFL50)

16-5/8 in. high x 9-5/8 in. base

(WCS50T)

ON LEVEL (FACTORY SET)

Approximately 16. in.

(RPP50)

Approximately 17 in.

(SEL50, EFL50)

Approximately 19 in.

(WCS50T)

OFF LEVEL (FACTORY SET) Approximately 7.5 in.

(RPP50)

Approximately 7 in.

(SEL50, EFL50)

Approximately 10.5 in.

(WCS50T)

610001W-001 E 1/20

CONSTRUCTION

MOTOR HOUSING

Cast Iron (RPP50, WCS50T)

Reinforced Thermoplastic (SEL50, EFL50)

VOLUTE

Cast Iron (RPP50, WCS50T)

Cast Iron

Reinforced Thermoplastic

(SEL50, EFL50)

Glass Reinforced Thermoplastic

IMPELLER Glass Reinforced Thermoplastic

SHAFT Steel

DISCHARGE 2 in. NPT

Sewage/Efﬂuent Pumps

Intended for Indoor Use Only

RPP50

Sewage- SEL50

Efuent- EFL50

WCS50T

Operating Instructions and Parts Manual Sewage/Effluent

Please read and save these instructions. Read carefully before attempting to assemble, install,

operate or maintain the product described. Protect yourself and others by observing all safety

information. Failure to comply with instructions could result in personal injury and/or property

damage! Retain instructions for future reference.

www.waynepumps.com

PERFORMANCE GAL/HR

Model HP

Discharge Head (Lift Distance)

0 ft 5 ft 10 ft 15 ft 20 ft

RPP50 1/2 6200 4800 3240 1500 -

SEL50 1/2 10000 9000 7200 5000 2000

WCS50T 1/2 10000 9600 8000 3300 -

EFL50 1/2 10000 9000 7200 5000 2000

Summary of content (12 pages)

PAGE 1
Sewage/Effluent Pumps Please read and save these instructions. Read carefully before attempting to assemble, install, operate or maintain the product described. Protect yourself and others by observing all safety information. Failure to comply with instructions could result in personal injury and/or property damage! Retain instructions for future reference.
PAGE 2
INSTALLATION MANUAL SEWAGE/EFFLUENT PUMP DESCRIPTION UNPACKING Sewage pumps are pumps used to remove waste water that contains solids up to 2 inches in diameter. The most common application is for draining bathroom waste water to a sewer or septic line. Effluent pumps are pumps used to remove gray water from septic tanks, sump pits, or laundry tray systems. Gray water is waste water from bathtubs, sinks, washing machines, and other kitchen appliances. Intended for indoor use only.
PAGE 3
INSTALLATION MANUAL ALWAYS DISCONNECT THE PUMP from power supply before installing, servicing or making any adjustments. TOUJOURS METTRE LA POMPE HORS TENSION avant de procéder à l’installation, à l’entretien ou à des réglages. DO NOT WALK on the floor when water is present until all power is turned off. If the electric panel is in the basement, call an electrician. NE PAS MARCHER sur un sol mouillé avant que l’alimentation générale ne soit coupée.
PAGE 4
INSTALLATION MANUAL IT IS REQUIRED TO USE RIGID PIPING AND FITTINGS to secure the pump in the basin and reduce pump movement. Pump movement can prevent the switch from operating correctly. Do not use flexible hosing. IL EST NÉCESSAIRE D’UTILISER DES TUYAUX ET DES RACCORDS RIGIDES pour fixer la pompe dans le système et réduire les mouvements de la pompe. Les mouvements de la pompe peuvent empêcher l’interrupteur de fonctionner correctement. Ne pas utiliser de tuyaux flexibles.
PAGE 5
INSTALLATION MANUAL TYPICAL SEWAGE INSTALLATION 1. This installation must be in accordance with the National Electric Code and all applicable local codes and ordinances. Submersible Sewage Pumps 2. Use a basin (5) that is large enough to accommodate the pump. The basin diameter should be a minimum of 18 inches and the depth a minimum of 24 inches. 2 3. Clean the basin of all debris. 4 5. Position pump (6) in the basin (5) so the tether switch (7) is away from incoming water.
PAGE 6
INSTALLATION MANUAL TYPICAL EFFLUENT INSTALLATION 1. This installation must be in accordance with the National Electric Code and all applicable local codes and ordinances. 2. Clean the basin of all debris. Effluent Pump in Septic Tank 3. Set the pump on a solid, level surface. Do not place pump directly on clay, earth, gravel, or sand. A brick or block may be installed under the pump to provide a solid base. 4 4.
PAGE 7
INSTALLATION MANUAL TROUBLESHOOTING WARNINGS ALWAYS DISCONNECT THE PUMP FROM POWER SUPPLY before installing, servicing or making any adjustments. TOUJOURS METTRE LA POMPE HORS TENSION avant de procéder à l’installation, à l’entretien ou à des réglages. 1. Submersible pump models have permanently lubricated bearings and require no additional lubrication. 2. Submersible pumps contain dielectric oil for cooling. Dielectric oil can be harmful to the environment.
PAGE 8
INSTALLATION MANUAL TROUBLESHOOTING (CONTINUED) Symptoms Possible Cause(s) Suggested Remedies Pump operates 1. Worn bearings noisily or vibrates 2. Impeller broken excessively 3. Piping attachments to building structure too rigid or too loose 1. Replace pump Pump will not shut off 1. Switch 1. Replace tether switch 2. Switch obstructions 2. Remove obstruction to verify free motion of switch 3. Restricted discharge (obstruction in piping) 3. Remove obstruction from discharge piping 4.
PAGE 9
WARRANTY & SERVICE PARTS SHEET - REPLACEMENT PARTS 2 REPAIR KITS 9 REF. NO. DESCRIPTION PART NUMBER 1 TETHER SWITCH 56835-WYN1 2 10 FT.
PAGE 10
INSTALLATION MANUAL ADDRESS PARTS CORRESPONDENCE TO: WAYNE Water Systems 101 Production Drive Harrison, OH 45030 U.S.A. FOR REPLACEMENT PARTS OR CUSTOMER SUPPORT, CALL 1-800-237-0987 Please provide following information: - Model number - Serial number on cord tag (not to be removed) - Part description and number as shown in parts list Thank you for making Wayne Water Systems a key part of your home maintenance program.
PAGE 11
NOTES www.waynepumps.
PAGE 12
www.waynepumps.