Stop basement floods before they happen.
History | of wayne water systems In 1928, Norbert G. Berghoff founded the Wayne Home Equipment Company located in Fort Wayne, Indiana. The Berghoff family was also known for owning and operating the famous Berghoff Brewery in Fort Wayne. Wayne Home Equipment manufactured oil burners for use in home furnaces, water and space heaters, boilers, and industrial ovens. Wayne became quite successful in the oil burner business, but faced the challenge that oil burners were seasonal in nature.
table of contents AT AdvanTEXT ® ....................................................................Page 3 AdvanTEXT ® Integrated Systems.......Page 4 AdvanTEXT ® Alarm..............................Page 4 AdvanTEXT ® Accessories...................Page 4 SUMP ....................................................................Page 5 Thermoplastic Submersible..................Page 6 Cast Iron Submersible...........................Page 8 12 Volt Batteries.....................................
AdvanTEXT ® | cellular flood monitoring Today’s homeowners lead on-the-go lifestyles. What if you could know instantly, anywhere you are, if your power is out, or if your sump system needs attention? AdvanTEXT ® detects power outage and high water levels and immediately sends a text alert to the mobile phone numbers you program in. HOW DOES THIS FLOOD MONITORING TECHNOLOGY WORK? AdvanTEXT ® uses M2M cellular technology, and it does not require a landline, internet service, or home network to operate.
AT ® Cellular Flood Monitoring WT50W WTXS WTX50 WFS WT50W 1/2 HP SEWAGE SYSTEM INTEGRATED WITH AdvanTEXT ® CELLULAR FLOOD MONITORING • Submersible, cast iron construction • 1/2 HP; max. flow rate is 8640 Gallons Per Hour; 6600 GPH at 10 ft. of discharge lift • 2 in. NPT discharge capable of passing 2 in. solids • Approximate on level @ 13 in. - off level @ 8 in.
sump | submersible sump pumps A sump pump is an automatic pump used to remove ground water from a sump pit. The most common application is for basement drainage to prevent residential flooding. FEATURES • Top suction pump design eliminates air locks and clogging from debris in bottom of sump pit • Fully submersible • 1-1/2 in. NPT discharge for standard plumbing installation • Durable construction materials INSTALLATION HIGHLIGHTS: If replacing an existing pump, remove the old pump carefully.
® ® ® WST50 | WST40 WST30 WSF50 RSP130 WSF50 1/2 HP THERMOPLASTIC WITH VERTICAL FLOAT SWITCH • Submersible, reinforced, corrosion-resistant sealed thermoplastic construction • 1/2 HP; max. flow rate is 2900 Gallons Per Hour; 2200 GPH at 10 ft. of discharge lift • For use in 11 in. diameter or larger sump basins; 7 in. ON level and 4 in.
® ® CDU800 | CDU790 CDT50 |CDT33 CDU800 | CDU790 CAST IRON WITH VERTICAL FLOAT SWITCH • Submersible Cast Iron and Coated Steel Sump Pump with Vertical Float Switch • 1/2 HP; max. flow rate is 4200 Gallons Per Hour; 3150 GPH at 10 ft. of discharge lift (CDU800) • 1/3 HP; max. flow rate is 3800 Gallons Per Hour; 2700 GPH at 10 ft. of discharge lift (CDU790) • For use in 11 in. diameter or larger sump basins; 9 in. ON level and 4 in.
sump | submersible sump pumps ® ® SPF50 | SPF33 SPT50 | SPT33 SPT50 | SPT33 REINFORCED THERMOPLASTIC WITH TETHER FLOAT SWITCH • Submersible coated steel and thermoplastic sump pump with tether float switch • 1/2 HP; max. flow rate is 3900 Gallons Per Hour; 2800 GPH at 10 ft. of discharge lift (SPT50) • 1/3 HP; max. flow rate is 3600 Gallons Per Hour; 2500 GPH at 10 ft. of discharge lift (SPT30) • For use in 14 in. diameter or larger sump basins; 13 in. ON level and 7 in.
sump | back-up & simple sump systems A battery back-up system is either a stand alone DC pump with a 12 Volt battery that can be used with your existing sump pump, or a battery back-up simple sump system that comes with a DC back-up pump, and a primary AC pump with the plumbing attached for easy "drop in the pit" installation.
WSB1240 WSB1275 WSB1240 MAINTENANCE FREE BATTERY WSB1275 MAINTENANCE FREE BATTERY • 12 Volt • 40 Amp Hour • Sealed Lead acid battery (no handling acid) • Pre-charged and ready to use • Compatible with all WAYNE battery back-up products • Carry handles for convenience • 12 Volt • 75 Amp Hour • Sealed Lead acid battery (no handling acid) • Pre-charged and ready to use • Compatible with all WAYNE battery back-up products • Carry handles for convenience BACK-UP DC SUMP PUMP DEEP CYCLE BATTERY SIZE 1X EVER
sump | back-up & simple sump systems ESP15 WSS20V ESP15 12 VOLT BATTERY BACK-UP SYSTEM • Fully submersible back up pump • Back-up pump max. flow is 1750 gallons per hour; 720 GPH at 10 ft.
ESP25 WSS30V ESP25 12 VOLT BATTERY BACK-UP SYSTEM • Fully submersible back up pump • Back-up pump max. flow is 3300 gallons per hour; 2300 GPH at 10 ft.
sump | back-up & simple sump systems ™ WSM3300 WSM3300 ADVANCED NOTIFICATION BACK-UP SYSTEM 12 VOLT BATTERY BACK-UP SYSTEM WITH ADVANCED NOTIFICATION SYSTEM INCLUDES: 15 10 5 WSM3300 0 1000 2000 3000 4000 TOTAL DYNAMIC HEAD (FT.
WSSM40V WSSM40V PRIMARY PUMP AND BACK-UP SYSTEM PRE-ASSEMBLED SUMP PUMP AND BACK-UP SYSTEM FOR QUICK AND EASY INSTALLATION! SYSTEM INCLUDES: • Top suction, durable, cast iron primary pump with vertical float switch • High flow, corrosion resistant, battery back-up pump with reliable reed float switch with battery box and charger • (2) Heavy-duty check valves • Professional grade back-up system keeps battery properly charged (Requires one 40 Amp Hr or 75 Amp Hr deep cycle battery) • Simple drop-in installation
sump | pedestal A pedestal pump is a sump pump where the motor is above the sump pit. These pumps are great for smaller diameter sump pits. Pedestal pumps have a vertical float which can be adjusted and leaves a smaller footprint in the sump pit. FEATURES • Top suction pump design eliminates air locks and clogging from debris in bottom of sump pit • Not Submersible • 1-1/2 in. NPT discharge for standard plumbing installation • For use in 11 in.
® ® SPV800 | SPV500 PTU50 | PTU30 SPV800 | SPV500 CAST IRON PEDESTAL (NON-SUBMERSIBLE) SUMP PUMP WITH ADJUSTABLE VERTICAL FLOAT SWITCH • 1/2 HP; max. flow rate is 5000 Gallons Per Hour; 3800 GPH at 10 ft. of discharge lift (SPV800) • 1/3 HP; max. flow rate is 4080 Gallons Per Hour; 2160 GPH at 10 ft.
effluent Effluent pumps are automatic pumps used to remove grey water (soiled) from septic tanks, sump pits, or laundry tray systems. Effluent pumps can pass up to 3/4 in. solids. FEATURES • Designed to handle 3/4 in. solids • Piggy-back tether float switch for automatic or manual operation Check Valve GFCI Outlet (recommended) AdvanTEXT® See pages 3-4 Discharge Pipe Vent Pipe Inlet Tether Float AdvanTEXT® On Level (User Adjustable) AdvanTEXT® Off Level (User Adjustable) On Level (approx 11 in.
® EFL33 EFL30 EFL33 THERMOPLASTIC EFFLUENT WITH TETHER FLOAT SWITCH • 1/3 HP; max. flow rate is 5700 Gallons Per Hour; 3600 GPH at 10 ft. of discharge lift • Reinforced, corrosion-resistant, thermoplastic submersible effluent pump • Combination 2 in./3 in. NPT discharge EFL30 CAST IRON EFFLUENT WITH TETHER FLOAT SWITCH • 1/3 HP; max. flow rate is 3900 Gallons Per Hour; 2900 GPH at 10 ft. of discharge lift • Durable, cast iron submersible effluent pump • 2 in.
sewage Sewage pumps are automatic pumps used when water being pumped contains solids up to 2 in. diameter. Pumping waste from a bathroom to a sewer or septic line is a common application. FEATURES • Will replace most sewage pumps without any plumbing changes • Piggy-back tether float switch for automatic or manual operation • Designed for 18 in. diameter or larger sewage basins • Pumps designed to handle 2 in.
® SEL50 | SEL40 RPP50 SEL50 | SEL40 THERMOPLASTIC SEWAGE WITH TETHER FLOAT SWITCH • 1/2 HP; max. flow rate is 7800 Gallons Per Hour; 6420 GPH at 10 ft. of discharge lift (SEL50) • 4/10 HP; max. flow rate is 5800 Gallons Per Hour; 3700 GPH at 10 ft. of discharge lift (SEL40) • Reinforced, corrosion-resistant, thermoplastic submersible sewage pump • Combination 2 in. / 3 in. NPT discharge capable of handling up to 2 in. solids RPP50 CAST IRON SEWAGE WITH TETHER FLOAT SWITCH • 1/2 HP; max.
sewage | cast iron WCS50T WCS50V WCS50T CAST IRON WITH TETHER FLOAT SWITCH • 1/2 HP; max. flow rate is 8400 Gallons Per Hour; 6600 GPH at 10 ft. of discharge lift • Piggy-back tether float switch for automatic or manual operation WCS50V CAST IRON WITH VERTICAL FLOAT SWITCH • 1/2 HP; max. flow rate is 8400 Gallons Per Hour; 6600 GPH at 10 ft.
AVAILABLE THROUGH MAY 2015 ® ® DSP75 | DSP60 CSE50TE DSP75 | DSP60 CAST IRON MANUAL OPERATION • 3/4 HP; max. flow rate is 8800 Gallons Per Hour; 7020 GPH at 10 ft. of discharge lift (DSP75) • 6/10 HP; max. flow rate is 8200 Gallons Per Hour; 6600 GPH at 10 ft.
sewage | cast iron SEP8 | SEP6 | SEP5 SEP4 SEP8 | SEP6 | SEP5 240 VOLT CAST IRON COMMERCIAL • 2 HP; max. flow rate is 13,800 Gallons Per Hour at 15 ft. of discharge lift ; 7020 GPH at 20 ft. of discharge lift. (SEP8) (not recommended for 10 ft. of lift or lower applications) • 1 HP; max. flow rate is 12,900 Gallons Per Hour @ 10 ft. of discharge lift ; 9000 GPH at 20 ft. of discharge lift. (SEP6) • 3/4 HP; max. flow rate is 10,800 Gallons Per Hour @ 10 ft. of discharge lift ; 6600 GPH at 20 ft.
® ® SYSSEL40 ® SYSEL40 SYDSP60 SYSSEL40 | SYSEL40 SEWAGE EJECTOR SYSTEMS • 4/10 HP; max. flow rate is 5800 Gallons Per Hour; 3700 GPH at 10 ft. of discharge lift • Reinforced, corrosion-resistant, thermoplastic submersible sewage pump • Piggy-back tether float switch for automatic or manual operation • Combination 2 in./3 in. NPT discharge capable of handling up to 2 in. solids • Cast iron seal plate • 2 in. vent opening in cover (unassembled SYSSEL40 model only) • 3 in.
utility | condensate | drill pump | kits Utility pumps are multi-purpose pumps. They range in use from everyday applications around your home to occasional use. Some typical applications include removing standing water off basement floors or construction sites, draining aquariums and water beds, emptying basement window wells, and boosting water pressure to wash a car.
® DPFTK1 WCP85 WDP21S WDP21S DRILL PUMP • Max. flow rate is 85 Gallons Per Hour at 0 ft.
utility | transfer | submersible PC4 | PC4K PC1 PC2 PC4 | PC4K CAST IRON TRANSFER PUMP • 1/2 HP; max. flow rate is 1450 Gallons Per Hour (at 5 PSI); 1350 GPH at 10 ft. of discharge lift (at 5 PSI) • Boosts line pressure up to 50 PSI PC4 / PC4K PERFORMANCE • Rugged, cast iron pump housing and motor with easy-priming outlet Discharge Pressure Suction Lift GPH - in ft. • 3/4 in. brass hose adapters connect to standard garden hose Per Square Inch • Includes suction strainer to filter debris PSI 0 ft. 5 ft.
® TSC130 | TSC160 GFU110 TSC130 | TSC160 PORTABLE ELECTRIC WATER REMOVAL PUMP • 1/4 HP; max. flow rate is 1050 Gallons Per Hour; 860 GPH at 10 ft. of discharge lift (TSC130) • 1/6 HP; max. flow rate is 950 Gallons Per Hour; 790 GPH at 10 ft. of discharge lift (TSC160) • 3/4 in. bronze garden hose adapter at discharge (TSC130) • 3/4 in. reinforced thermoplastic garden hose adapter at discharge (TSC160) • Lifts water over 25 ft.; removes water down to 1/8 in.
utility | submersible | gasoline-powered SENSING TECHNOLOGY ® VIP50 | VIP25 | VIP15 RUP160 | RUP160H EEAUP250 VIP50 | VIP25 | VIP15 THERMOPLASTIC PORTABLE ELECTRIC WATER REMOVAL PUMP • 1/2 HP; max. flow rate is 2500 Gallons Per Hour; 1550 GPH at 10 ft. of discharge lift (VIP50) • 1/4 HP; max. flow rate is 1800 Gallons Per Hour; 1020 GPH at 10 ft. of discharge lift (VIP25) • 1/5 HP; max. flow rate is 1700 Gallons Per Hour; 780 GPH at 10 ft.
GPH400 GPB400 GPH550 GPB400 PORTABLE GAS-POWERED WATER TRANSFER PUMP • Pumps large amounts of dirty water (up to 3/8 in. solids) with 2 in. hose • OHV 4-cycle Briggs and Stratton gas engine with all-metal pump construction • Heavy-duty aluminum carrying handle • 4.0 HP; Max. flow rate is 7200 Gallons Per Hour; 6600 GPH at 20 ft. of discharge lift • 2 in.
lawn | portable | permanent Lawn pumps are used when a lake, pond or municipal water is pumped for irrigation. Pumping water from a lake to power lawn or garden sprinklers is the most common application. COMMON FEATURES • Durable corrosion resistant construction • Lift water as high as 25 ft.
PLS100 WLS75 | WLS100 | WLS150 | WLS200 PLS100 PORTABLE STAINLESS STEEL WATER SPRINKLING PUMP • 1 HP; max. flow rate is 720 Gallons Per Hour; 520 GPH at 10 ft. of discharge lift • Portable stainless steel with safe and convenient on/off switch and easy carry handle for portability • Fan cooled continuous-duty 115 volt motor draws water up to 20 ft. • 1 in. NPT suction and discharge threads, 3/4 in. garden hose adapter included • 180 ft.
pool | pool cover pump | pool Pool cover pumps are used to remove water that collects on your pool cover. This is especially helpful for opening a pool in the spring, to remove the water weight. Pool pumps are used to circulate water as part of a swimming pool water filtration system.
WAPC250 | WAPC250G WIP90 | WIP150 WAPC250 | WAPC250G AUTOMATIC ON/OFF WATER REMOVAL POOL COVER PUMP • iSwitch technology turns pump on and off by sensing the presence of water • Plug in, and leave unattended for worry-free water removal • Strainer base filters debris to minimize clogging and keep pump from tipping over • Max. flow rate is 3000 Gallons Per Hour; 1850 GPH at 10 ft. of discharge lift (using 1-1/4 in.
well | submersible Well pumps are used to deliver water from an underground water source to your home. We offer 3 types of well pumps: shallow well jet pumps, convertible well jet pumps and deep well submersible pumps. Shallow well jet and convertible well jet pumps are NOT submersible and are usually placed outside the well in a well housing. Deep well submersible pumps are submerged inside your well, and provide water from depths greater than 100 ft.
T50S 10-2 | T50S 10-4 | T51S 10-4 | T75S 10-2 | T75S 10-4 | T100S 10-2 T50S 10-2 | T50S 10-4 | T51S 10-4 | T75S 10-2 | T75S 10-4 | T100S 10-2 DEEP WELL SUBMERSIBLE • 1/2 HP; max. flow rate is 165 Gallons Per Hour; at 100 ft. (50 PSI) (Models T50S 10-2 / T50S 10-4 / T51S 10-4) • 3/4 HP; max. flow rate is 535 Gallons Per Hour; at 100 ft. (50 PSI) (Models T75S 10-2 / TT75S 10-4) • 1 HP; max. flow rate is 541 Gallons Per Hour; at 100 ft.
well | shallow well | convertible well SWS50 | SWS75 | SWS100 JSU50 SWS50 | SWS75 | SWS100 CAST IRON SHALLOW WELL JET PUMPS • 1/2 HP; max. flow rate is 420 Gallons Per Hour; (50 PSI) (SWS50) • 3/4 HP; max. flow rate is 510 Gallons Per Hour; (50 PSI) (SWS75) • 1 HP; max. flow rate is 630 Gallons Per Hour; (50 PSI) (SWS100) JSU50 CAST IRON SHALLOW WELL JET PUMP • 1/2 HP; max. flow rate is 324 Gallons Per Hour; (50 PSI) FEATURES • 3/4 in. NPT discharge with 1-1/4 in.
CWS50 | CWS75 | CWS100 JCU50 CWS50 | CWS75 | CWS100 CAST IRON CONVERTIBLE WELL JET PUMPS FEATURES • 1/2 HP; max. flow rate is 408 Gallons Per Hour; (50 PSI) (CWS50) • 3/4 HP; max. flow rate is 462 Gallons Per Hour; (50 PSI) (CWS75) • 1 HP; max. flow rate is 588 Gallons Per Hour; (50 PSI) (CWS100) • 3/4 in. NPT discharge with 1-1/4 in. NPT suction and 1 in.
well | precharged air tank systems SWS50-WX102 JSU50-8.5X SWS50-30P PRECHARGED AIR TANK SYSTEMS WAYNE's precharged air tank systems are highly reliable and capable of maintaining a water supply equal to conventional tanks twice their size. All tanks include premium grade bladders or diaphragms, which eliminate the problem of water-logged tanks. Model Limited Warranty Part No. Description SWS50 - WX102 3 Years 56909 1/2 HP shallow well system with 4.
specialty | laundry tray | booster SYLT30 SWS50BOOST SYLT30 LAUNDRY TRAY SYSTEM • 1/3 HP; max. flow rate is 3060 Gallons Per Hour; 2460 GPH at 10 ft. of discharge lift • Durable, reinforced, thermoplastic pump • 10 gallon capacity, durable thermoplastic tank with 1-1/2 in. NPT inlet, 1-1/2 in. discharge and vent • Pre-assembled and job ready with detailed instructions • Ideal for draining sinks, washing machines and laundry trays that are below the sewer line without breaking concrete • 1-1/2 in.
accessories | sump SUMP ACCESSORIES CHECK VALVES HOSE KITS PUMP SWITCH and KITS MODEL # DESCRIPTION UPC 0-40066 SHIP WEIGHT 57028-001 1-1/4 in. - 1-1/2 in. Check Valve Kit 10395-6 11 oz. 28211-WYN1 "Silent" Check Valve 21607-6 1 lb. 66005-WYN1 1-1/2 in. Check Valve 20370-0 6 oz. UPC 0-40066 SHIP WEIGHT MODEL # 56171 1-1/4 in. x 24 ft. Sump Pump Discharge Hose Kit 10400-7 3 lbs. 66000-WYN1 1-1/2 in. x 24 ft. Sump Pump Discharge Hose Kit 20353-3 3 lbs. 66343-UNIV 1-1/4 in.
accessories | sewage | utility SEWAGE ACCESSORIES CHECK VALVE MODEL # UPC 0-40066 SHIP WEIGHT 2 in. Flow Check Valve Kit 10792-3 1 lb. 56805-002 3 in. Flow Check Valve 20183-6 1 lb. MODEL # DESCRIPTION 20631-2 2 lbs. 66038-WYN1 FLOAT SWITCH AU5RT BASINS and COVERS MODEL # DESCRIPTION 120 Volt Reverse Tether Switch with Piggy-Back Plug DESCRIPTION 56286 18 in. x 30 in. Basin with 2 in. Discharge Cover 20189-8 26 lbs. 56287 18 in. x 30 in. Basin with 3 in.
accessories | utility | well UTILITY ACCESSORIES - CONTINUED REPAIR / MAINTENANCE KITS DRILL PUMP and KIT MODEL # DESCRIPTION UPC 0-40066 SHIP WEIGHT 56397 PC4 Brush Replacement Kit (brush kit caps only) 10392-5 1 oz. 56399 PC4 Repair Kit (brushes, caps, impeller, shaft seals, gasket and ball bearing) 10394-9 4 oz. 56671 PC4 Repair Kit (shaft seal, impeller and gaskets) 10913-2 3 oz. 62015-WYN1 PC4 Brush and Holder Kit 20589-6 1 oz.
accessories | well WELL ACCESSORIES AIR VOLUME CONTROLS MODEL # 15902-WYN1 Type WJ for Deep Well 15956-WYN1 Type L with Tubing WELL PUMP ACCESSORIES SWITCHES / CONTROL BOX 1 lb. 20111-9 1 lb. Deluxe Submersible Torque Arrestor 20266-6 3 oz. 17067-001 Pitless Adapter 20257-4 3 oz. 3-Wire Splicing Kit 20174-4 3 oz. UPC 0-40066 SHIP WEIGHT 20# 40# Setting 30# 50# Setting 30# 50# Setting (tubing sold separately) 10389-5 10434-2 21063-0 11 oz. 11 oz. 0.7 oz.
accessories | well JET WELL ASSEMBLIES All WAYNE CWS jet pumps require a jet assembly to complete installation. The Shallow Well Jet Assembly mounts directly to the front of CWS pump, while the 2 in. and 4 in. Well Jet Assemblies are installed in the well itself. SHALLOW WELL JET ASSEMBLY: Jet body, venturi, nozzle, gasket, mounting screws 2 in. JET ASSEMBLY: Jet body, jet packer, venturi, adapter, nozzle, foot valve 4 in.
15266-WYN1 15453-WYN1 15267-WYN1 15454-WYN1 15596-WYN1 15522-WYN1 15537-WYN1 15591-WYN1 15739-WYN1 15767-WYN1 15792-WYN1 15791 BRONZE CHECK VALVES BRONZE FOOT VALVES Low-lead compliant. Foot valves feature perforated brass strainer. FOOT VALVES Low-lead compliant. Precision machined, one piece, cast bronze body with one piece poppet and high quality spring. FOOT VALVES Well Size - ID UPC 0-40066 Ship Weight Part No. Well Size - ID 15266-WYN1 1 in. 10800-5 1 lb.
accessories | well PRECHARGED WATER SYSTEM TANKS Enamel coated steel tanks provide easy accessibility for installation. Heavy duty bladder - FDA approved material is capable of expanding 4 times its normal size. It eliminates water-logging, corrosion, and rust as water never contacts the air in the tank. Precharged tanks deliver draw down equal to conventional tanks twice their size. Bottom discharge combats taste and odor, and allows universal replacement with 90% of market.
index | AdvanTEXT® | sump | sewage ADVANTEXT® Model No. Finished Good UPC 0-40066 Length (in) Width (in) Height (in) Cube Feet WTXS 71024-WYN1 21593-2 10 4 12 .3 Ship Wt. (lbs) 3 WTX50 70126-WYN1 21595-6 11.5 11.5 14 .85 20 WT50W 70128-WYN1 21597-0 17 9.5 19.5 1.82 40 Model No. Finished Good UPC 0-40066 Length (in) Width (in) Height (in) Cube Feet Ship Wt. (lbs) SPV800 56285 10042-9 8.30 8.30 35.80 1.43 27 SPV500 56128 10032-0 8.30 8.30 35.80 1.
index | utility | lawn | pool | well UTILITY Model No. Finished Good UPC 0-40066 Length (in) Width (in) Height (in) Cube Feet Ship Wt. (lbs) WDP21S 56678-WYN1 10399-4 0.10 5.00 9.00 0.07 6 oz. WCP85 59907-WYN1 21110-1 5.50 10.50 5.50 0.18 5 DPFTK1 62027-WYN1 20618-3 7.50 2.75 6.38 0.08 13 oz. PC1 57716-WYN1 20619-0 9.00 9.00 7.60 0.36 6.3 PC4 55832 10058-0 9.80 6.00 8.50 0.29 14 PC4K 57727-WYN1 21133-0 8.50 12.00 9.50 0.56 19 7.
index | specialty SPECIALTY Model No. Finished Good UPC 0-40066 Length (in) Width (in) Height (in) Cube Feet SYLT30 57399-WYN4 20835-4 17.30 11.30 16.50 1.87 Ship Wt. (lbs) 32 SWS50BOOST 01270-WYN1 21216-0 13.75 28.75 27.75 6.35 60 Model No. Finished Good UPC 0-40066 Length (in) Width (in) Height (in) Cube Feet Ship Wt. (lbs) 56286 71024-WYN1 20189-8 10.12 4.25 12.12 .3 3 56287 56827 20280-2 22 22 31 8.68 26 28485-WYN1 28485-WYN1 21352-5 21.75 21.75 30 8.
AT AdvanTEXT ® Sump Sewage Utility Lawn Pool Well Specialty Accessories WAYNE WATER SYSTEMS | 101 PRODUCTION DRIVE | HARRISON, OHIO 45030 | 1-800-237-0987 www.waynepumps.com | © 2014, WAYNE/Scott Fetzer Company.
