Instruction Manual
BLIND FASTENER INSTALLATION
Note: Make sure there is enough hole depth before installing the Blind Fastener.
Note: Black Oxide Bolt, Flat Washer, and Installation Tool are only used to install Blind Fasteners.
• Install Blind Fastener using Figure 3 as a guide.
• Place a drop of oil on black oxide bolt for lubrication.
• Insert Blind Fastener in the hole.
• Hold the “Installation Tool” with a 9/16” wrench while turning the ”Black Oxide Bolt” with a 1/2” wrench until fully seated.
• When Blind Fastener is fully seated, continue with installation.
BlindFastInstall-1.eps
Black Oxide Bolt
Flat Washer
9/16" Wrench
Installation Tool
Blind Fastener
FEATURE OPERATION
WARNING
To prevent electric shock, explosion, re and/or serious personal injury when using side box with:
Extension Cord -
• Follow all Extension Cord manufacturer’s warnings and instructions.
• Do NOT insert extension cord through hole without grommet in place (see Figure 4).
• Only use a three-wire extension cord with all three prongs intact. Never remove the round grounding prong.
• Extension cord must be connected to a 120 Volt GFCI (fround fault circuit interrupter) protected outlet with proper ground. If GFCI outlet is not
available, use an extension cord with GFCI protection built in.
• Check the insulation and plugs of extension cord before using. Do NOT use cord if it is worn or damaged.
• Do NOT overload extension cord.
• Remove extension cord from the grommet hole before moving or transporting side box.
• Only use an extension cord that is rated for outdoor use.
• Do NOT connect extension cord to outlet that also supplies power for critical safety equipment.
Cordless Power Tool Battery Chargers -
• See Charger’s Owner's Manual for proper use and care of charger and batteries. Follow all warnings and instructions provided with your battery charger.
• Place chargers and electrical connections in tray.
• Chargers are Dry location use only. Do NOT expose to liquid, vapor, or rain. Should your charger become wet, do NOT attempt to use.
Unplug extension cord from supply before handling wet charger or cords.
• Only use chargers and batteries that are intact and operating properly.
• Do NOT touch metal prongs when plugging charger into extension cord.
• Keep ammable materials like paper or rags away from charger, cords or connections.
• Do NOT place or attempt to charge lead-acid, car-type batteries in side box.
Figure 3
Figure 4
MountingClamp&Bolt.eps
w
e
a
t
h
e
r
g
u
a
r
d
®
LOCK SYSTEM
The WEATHER GUARD® Lock is designed to provide maximum security, while providing ease of use and
years of reliable service. When in the locked mode, the button remains retracted in a tamper-resistant position.
When the button is pressed in the unlock mode, the latch is activated and the cover opens.
LOCK
Turn key counter-clockwise to locked position
as indicated on lock bezel. When the button
is now pressed, it will stay in the retracted or
tamper-resistant position until unlocked.
UNLOCK
Turn key clockwise to unlock position as
indicated on lock bezel. Button will pop out
and is now ready to release the latches when
pressed.
MOUNTING BRACKETS
Wide ange mounting bolts provide secure mounting without crimping bed rails and allow full
unobstructed use of side pockets.
LATCH SYSTEM
The WEATHER GUARD Latch System utilizes an automotive-grade latch in conjunction with a high strength latch striker to
ensure maximum security. The WEATHER GUARD Latch System is designed to open with a single touch of the button, and close
securely. Expect years of reliable service from the WEATHER GUARD Latch System with only minimal maintenance: Bi-annually
lubricate latch pivot points with white grease. If latch striker is accidentally knocked out of alignment, simply use a mallet to realign.
12V ELECTRICAL ACCESS
WEATHER GUARD Truck Boxes are equipped with a 12 Volt Electrical Access Grommet
for easy electrical accessory t-ups. To use, simply cut along one or more perforations in
the rubber grommet and run wire through.