Assembly Instructions

USER INSTRUCTIONS
Page 11
STEP 6 - INSTALL CENTER CONNECTING TUBE
• FOR 2265-3-01, PROCEED TO STEP 7
Rotate and position the connecting tube on the drive tube until all 4
mounting holes line up. Using 2-5/16x1-3/4” bolts, 4-5/16” washers, and
2-5/16” nuts, install the connecting tube. Torque 5/16 nuts to 17 ft-lbs.
Using 2-5/16x1-3/4” bolts, 4-5/16” washers, and 2-5/16” nuts, install
the connecting tube on the front drive tube. Rotate and position the center
connecting tube until all 4 mounting holes line up and then drop cross
member onto stud plates. Torque 5/16 nuts to 17 ft-lbs.
5/16 WASHER
5/16 X 1-3/4” BOLT
FRONT CROSS
MEMBER
ASSEMBLY
5/16 LOCK NUT
RED CAP
DRIVE TUBE
IT IS RECOMMENDED THAT THE REAR CROSSMEMBER BE
LOCATED APPROXIMATELY 1-3" FROM THE REAR OF
THE MOUNTING CHANNEL
STEP 7- INSTALL CENTER CONNECTING TUBE
USING 4-5/16X1-3/4" BOLTS, 8-5/16" WASHERS, AND 4-5/16" NUTS, INSTALL THE CONNECTING TUBE.
ROTATE AND POSITION TUBE UNTIL ALL 4 MOUNTING HOLES LINE UP WITH FRONT DRIVE TUBE AND
THEN DROP CROSS MEMBER ONTO STUD PLATES. TORQUE 5/16 NUTS TO 17 FT-LBS
ON TRANSIT INSTALLATIONS IT IS OK TO PLACE THE CURVED MOUNTING BRACKET ON TOP OF THE
MOUNTING CHANNEL END CAPS AND PINCH THEMBETWEEN THE MOUNTING CHANNEL.
Torque to 17 ft-lbs
Torque to 17 ft-lbs
SLIDE FRONT X-MEMBER FORWARD TO CLEAR TUBE
SLIDE FRONT X-MEMBER REAR TO CAPTURE TUBE
2295-3-01
FRONT OF VEHICLE
KNAACK L.L.C.
CONFIDENTIAL, PRINTED
COPIES ARE NOT TO BE
REMOVED FROM SITE
WITHOUT WRITTEN CONSENT.
THIRD ANGLE PROTECION
FORMAT
SW
PAGE NUMBER
SCALE:
DATE:
DRAWN BY:
PART NAME:
MATERIAL:
TOLERANCES=
(EXCEPT AS NOTED)
ANGULAR
±1°
LINEAR
±.031
=CONTROL DIMENSION
1:24
2291-3-01 INSTALL 3
PAGE OF
2114
PART NUMBER: REV.
REV.
PART NUMBER:
5/16
WASHER
5/16 X 1-3/4”
BOLT
CONNECTING TUBE
REAR CROSS
MEMBER
ASSEMBLY
5/16 LOCK NUT
IT IS RECOMMENDED THAT THE REAR CROSSMEMBER BE
LOCATED APPROXIMATELY 1-3" FROM THE REAR OF
THE MOUNTING CHANNEL
STEP 7- INSTALL CENTER CONNECTING TUBE
USING 4-5/16X1-3/4" BOLTS, 8-5/16" WASHERS, AND 4-5/16" NUTS, INSTALL THE CONNECTING TUBE.
ROTATE AND POSITION TUBE UNTIL ALL 4 MOUNTING HOLES LINE UP WITH FRONT DRIVE TUBE AND
THEN DROP CROSS MEMBER ONTO STUD PLATES. TORQUE 5/16 NUTS TO 17 FT-LBS
ON TRANSIT INSTALLATIONS IT IS OK TO PLACE THE CURVED MOUNTING BRACKET ON TOP OF THE
MOUNTING CHANNEL END CAPS AND PINCH THEMBETWEEN THE MOUNTING CHANNEL.
Torque to 17 ft-lbs
Torque to 17 ft-lbs
SLIDE FRONT X-MEMBER FORWARD TO CLEAR TUBE
SLIDE FRONT X-MEMBER REAR TO CAPTURE TUBE
2295-3-01
FRONT OF VEHICLE
KNAACK L.L.C.
CONFIDENTIAL, PRINTED
COPIES ARE NOT TO BE
REMOVED FROM SITE
WITHOUT WRITTEN CONSENT.
THIRD ANGLE PROTECION
FORMAT
SW
PAGE NUMBER
SCALE:
DATE:
DRAWN BY:
PART NAME:
MATERIAL:
TOLERANCES=
(EXCEPT AS NOTED)
ANGULAR
±1°
LINEAR
±.031
=CONTROL DIMENSION
1:24
2291-3-01 INSTALL 3
PAGE OF
2114
PART NUMBER: REV.
REV.
PART NUMBER: