Assembly Instructions

Page 12
STEP 7 - MOUNT CENTER CROSS
MEMBERS TO VEHICLE
Slide two stud plates per mounting
channel into mounting channel if
not already done. If installing a dual
setup with 3 cross members, 3 stud
plates will be used per mounting
channel. Using 2-1/4” washers,
2-1/4” nylon lock nuts, and 1
mounting foot bolt plate per mounting
foot, install the rear cross member
on the mounting channel. The cross
member that has the slide down
mechanism should be installed in the
rear position.
The EZ GLIDE2 can be installed on
either the street side or curb side of
the van. Decide which side to install
the drop-down before mounting it to
the vehicle.
Locate the cross member
approximately 1-3” from the end
of the mounting channel and hand
tighten each 1/4” nut. The 1/4” nuts
will need to be kept loose until step 7
is complete.
R
AE
IT IS RECOMMENDED THAT THE REAR CROSSMEMBER BE
LOCATED APPROXIMATELY 1-3" FROM THE REAR OF
THE MOUNTING CHANNEL
FRONT OF VEHICLE
PASSENGER SIDE
OF VEHICLE
DETAIL R
SCALE 1 : 4
STEP 6- MOUNT CROSS MEMBERS TO VEHICLE
Torque to 8 ft-lbs
SLIDE TWO STUD PLATES PER MOUNTING CHANNEL INTO MOUNTING CHANNEL IF NOT ALREADY DONE.
IF INSTALLING A DUAL SETUP WITH 3 CROSS MEMBERS, 3 STUD PLATES WILL BE USED PER MOUNTING CHANNEL
USING 2-1/4" WASHERS, 2-1/4" NYLON LOCK NUTS, AND 1 MOUNTING FOOT BOLT PLATE PER MOUNTING
FOOT, INSTALL THE REAR CROSS MEMBER ON THE MOUNTING CHANNEL
LOCATE THE CROSS MEMBER APPROXIMATELY 1-3" FROM THE END OF THE MOUNTING CHANNEL AND
HAND TIGHTEN EACH 1/4" NUT. THE 1/4" NUTS WILL NEED TO BE KEPT LOOSE UNTIL STEP 7 IS COMPLETE
KNAACK L.L.C.
CONFIDENTIAL, PRINTED
COPIES ARE NOT TO BE
REMOVED FROM SITE
WITHOUT WRITTEN CONSENT.
THIRD ANGLE PROTECION
FORMAT
SW
PAGE NUMBER
SCALE:
DATE:
DRAWN BY:
PART NAME:
MATERIAL:
TOLERANCES=
(EXCEPT AS NOTED)
ANGULAR
±1°
LINEAR
±.031
=CONTROL DIMENSION
1:24
2291-3-01 INSTALL 3
PAGE OF
1910
PART NUMBER: REV.
REV.
PART NUMBER:
R
AE
IT IS RECOMMENDED THAT THE REAR CROSSMEMBER BE
LOCATED APPROXIMATELY 1-3" FROM THE REAR OF
THE MOUNTING CHANNEL
FRONT OF VEHICLE
PASSENGER SIDE
OF VEHICLE
DETAIL R
SCALE 1 : 4
STEP 6- MOUNT CROSS MEMBERS TO VEHICLE
Torque to 8 ft-lbs
SLIDE TWO STUD PLATES PER MOUNTING CHANNEL INTO MOUNTING CHANNEL IF NOT ALREADY DONE.
IF INSTALLING A DUAL SETUP WITH 3 CROSS MEMBERS, 3 STUD PLATES WILL BE USED PER MOUNTING CHANNEL
USING 2-1/4" WASHERS, 2-1/4" NYLON LOCK NUTS, AND 1 MOUNTING FOOT BOLT PLATE PER MOUNTING
FOOT, INSTALL THE REAR CROSS MEMBER ON THE MOUNTING CHANNEL
LOCATE THE CROSS MEMBER APPROXIMATELY 1-3" FROM THE END OF THE MOUNTING CHANNEL AND
HAND TIGHTEN EACH 1/4" NUT. THE 1/4" NUTS WILL NEED TO BE KEPT LOOSE UNTIL STEP 7 IS COMPLETE
KNAACK L.L.C.
CONFIDENTIAL, PRINTED
COPIES ARE NOT TO BE
REMOVED FROM SITE
WITHOUT WRITTEN CONSENT.
THIRD ANGLE PROTECION
FORMAT
SW
PAGE NUMBER
SCALE:
DATE:
DRAWN BY:
PART NAME:
MATERIAL:
TOLERANCES=
(EXCEPT AS NOTED)
ANGULAR
±1°
LINEAR
±.031
=CONTROL DIMENSION
1:24
2291-3-01 INSTALL 3
PAGE OF
1910
PART NUMBER: REV.
REV.
PART NUMBER:
DRIVER SIDE OF VEHICLE
1/4 LOCK NUT
1/4 WASHER
STUD PLATE
MOUNTING CHANNEL
REAR OF VEHICLE