Installation Guide

ManualsBrandsWEATHER GUARD ManualsTruck Tool Box Accessories308-5

ATTENTION: PLEASE READ AND UNDERSTAND ALL INSTRUCTIONS AND WARNINGS

BEFORE ASSEMBLING, INSTALLING OR USING THIS PRODUCT.

TRUCK AND VAN STORAGE SOLUTIONS

SECURING YOUR REPUTATION

WEATHERGUARD.COM

INSTALLATION MANUAL

STEEL & ALUMINUM SIDE BOX WITH

PACK RAT

DRAWER UNITS

NOTICE WARNING

MODELS

DANGER CAUTION

Use specic aluminum upt components when installing WEATHER GUARD®

products to aluminum truck beds. Follow additional instructions if mounting

to an aluminum truck bed. There may be left over components depending on

upt.

Any modication or unintended use of this product shall immediately void all

manufacturers warranties. Manufacturer disclaims all liability for injuries to

persons or property resulting from any modication to, or unintended use of

this product.

Danger of explosion. Do not use this product for storing or transporting

ammables, explosives, hazardous materials, or hazardous waste, such

as containers of gasoline, solvents, gun powder, dynamite, propane tanks,

acetylene tanks and cutting torches. This product is only intended and safe

for use in storing and transporting small tools, equipment and other similar

materials. Any modications made to, or unintended use of this product, could

create a hazardous condition that can cause death, serious personal injury or

property damage.

Part No. 24-0144 REV. C ECN 5583 05/15

Prior to drilling, so as not to cut or puncture fuel tanks, fuel lines, electric

wires, etc., check under vehicle for locations. All oor mounting bolts near

the gas tank area should be installed from the underside of the vehicle, to

guard against the gas tank being punctured in the event of a collision. This

would mean not using Blind Fastener in this area. Holes drilled in this area

should be 3/8".

To keep debris out of your eyes when checking the underside of the vehicle,

or when drilling, always wear protective eyewear.

Some of the larger drawers would best be handled by two people, so as not

to cause injury to your person.

PACK RAT

DRAWER UNITS

Note: X represents the color code for your model: 3 = White | 5 = Black

300, 301-X, 302, 303-X, 304-X, 305-X, 306-X, 307-X, 308-X, 312-X, 334-X, 335-X, 336-X, 337-X, 338-X

Summary of content (5 pages)

PAGE 1
INSTALLATION MANUAL TRUCK AND VAN STORAGE SOLUTIONS SECURING YOUR REPUTATION ® STEEL PACK & ALUMINUM BOX WITH RAT®SIDE DRAWER ® PACK RAT DRAWER UNITS UNITS ATTENTION: PLEASE READ AND UNDERSTAND ALL INSTRUCTIONS AND WARNINGS BEFORE ASSEMBLING, INSTALLING OR USING THIS PRODUCT.
PAGE 2
TOOLS REQUIRED • Screwdriver (common) • Electric Drill • Drill Bits - 3/8" & 1/2" • 1/2" Open or Box End Wrench • 9/16" Open or Box End Wrench • Ratchet Wrench • 1/2" Socket PARTS LIST (4) 5/16-18 x 1" Hex Head Bolt (6) 5/16-18 x 1-1/2" Hex Head Bolt (1) 5/16-18 x 2-1/4" Black Oxide Bolt (6) 5/16" Lock Washer (10) 5/16" Flat Washer (2) 5/16-18 x 3/4" Truss Head Screw (6) 5/16-18 Blind Fastener (1) Installation Tool (4) 5/16-18 Nylon Lock Nut (2) 5/16-18 Whiz Lock Nut (1) Handle (4) Mounting
PAGE 3
INSTALLATION INSTRUCTIONS Note: If your truck bed is constructed of aluminum, use zinc rich primer to coat drilled holes. STEP 1 Drawer Removal Open the drawer until it reaches the internal stop brackets. Remove the stop brackets from each upper inside location. Put the brackets and bolts into the drawer for later installation. Install the drawer handle. Carefully pull the drawer completely out of the housing, setting it aside. Lift out the front rollers.
PAGE 4
STEP 2B Rear Mount Bracket Installation (alternate) If space is critical and/or for some reason you cannot mount the rear in either the preferred method or use the mounting plates at the rear, you may use the rear mounting bracket. Locate the center line of the housing and place the bracket flush against the back and flush to the floor. If necessary, you may turn the bracket so the floor flange is under the rear overhang of the housing. Hole marking will be more difficult.
PAGE 5
KNAACK LLC LIMITED LIFETIME WARRANTY FOR WEATHER GUARD® PRODUCTS WEATHER GUARD® Products — Limited Lifetime Warranty (Purchased on or after 1/1/2009) KNAACK LLC (the “Manufacturer”) warrants to the original purchaser only that WEATHER GUARD® Truck and Van Products (the “WEATHER GUARD® Product”) will be free from defects in material and workmanship from the date of purchase and continuing for the expected lifetime of the WEATHER GUARD® Product.