easyONE-DSCCL A10901/A10902 AIS MOB + DSC User manual english Vers.: 1.2 Stand 1.
Inhalt 2 FCC STATEMENT ................................................... 5 3 SAFETY INFORMATION ........................................ 5 4 PRODUCT AND PERFORMANCE DESCRIPTION ...6 4.1 USE FOR INTENDED PURPOSE .......................................6 5 PRODUCT OVERVIEW ...........................................8 6 OPERATING ELEMENTS ........................................9 6.1 6.2 6.3 6.4 ALARM FLAP .............................................................9 „ON“ BUTTON ................
9 LIFE JACKET INTEGRATION ................................ 29 10 MAINTENANCE AND SERVICE ............................ 31 10.1 10.2 10.3 10.4 10.5 BASIC ANTENNA POSITION ........................................ 31 MAINTENANCE/SERVICE ............................................ 34 CLEANING ............................................................... 34 CONTACT AND PRODUCT SUPPORT............................. 34 DISPOSAL................................................................
Table of abriviations AIS Automatic Identification System COG Course over Ground DSC Digital Selective Call ECDIS Electronical Chart Display GMDSS Global Maritime Distress and Safety System GNSS Global Navigation Satellite System MMSI Maritime Mobile Service Identification MOB Man over Board SAR Search and Rescue SOLAS Safety of Life at Sea SOG Speed over Ground Weatherdock AG www.easyAIS.
2 FCC Statement This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
• Caution: Risk of explosion if battery is replaced by an incorrect battery type. Dispose of used batteries according to instructions. • The capacity of the batteries decreases if the device is used at a temperature below 0°C or above 55°C. Keep the device away from heat or hot environments. If these safety instructions are not observed, the batteries may overheat, explode or ignite inside the easyONE-DSCCL and may cause permanent damage to the device or environment. 4 4.
• DSC Closed Loop: Only pre-programmed MMSIs of DSC receivers within range (Every 5 minutes for the first 30 minutes, then every 10 minutes) DSC Open Loop: All DSC receivers within range of the • transmitter (possible for one time) These recipients get information about the event of a distress situation as well as the current position.
5 Product overview 1. Bottom section housing 2. Upper section 3. Antenna flap 4. Alarm flap 5. Antenna 6. Antenna winding head 7. “TEST” button Weatherdock AG www.easyAIS.com 8. “ON” button 9. Seizing, 1m 10. GPS status LED 11. FLASH LEDs 12. Red FLARE LED 13.
6 Operating elements 6.1 Alarm flap The transparent plastic cover (4) in the upper frontal section of the device serves to avoid false alarms and locks the antenna flap (3) at the same time. 6.2 „ON“ button The easyONE-DSCCL can be activated manually by pressing the “ON“ button (8). Parallel to the AIS Signal a DSC distress call is broadcasted. (only to pre-programmed MMSI numbers) (more information for alert functionality see chap. 5.1) Seite 9 Weatherdock AG www.easyAIS.
6.3 „TEST“ button The device can be activated for an electrical function test by pressing the “TEST“ button (7). In addition to the AIS test message an onetime DSC distress call is sent to all preprogrammed MMSI numbers. The red LED FLARE is also activated once. During test transmission the red LEDs are blinking. 6.4 Antenna The antenna (5) is rolled up in the upper section of the transmitter. It’s locked by a water soluble pill (12) and the alarm and antenna flap.
7 Operation The easyONE-DSCCL is floatable without any floatation aids. During heavy sea the floating AIS MOB easyONE-DSCCL may take a longer time to get the position information by GPS/GNSS. The best AIS transmitter and GPS/GNSS receiver performance will be achieved by holding the distress transmitter with your hands as far away from the water as possible.
7.1 7.1.1 ALERT Automatic Activation (only A10901) The AIS/DSC MOB easyONE-DSCCL is designed for carrying it in an automatic life jacket. If falling into the water, the life jacket opens and the floating body inflates due to the water contact. As a result, the transmitter gets into the water and the antenna is released. If the antenna is unfolded, two contacts are exposed through which the transmitter activates independently upon concurrent water contact.
7.1.3 Functionality AIS Upon an automatic or manual activation of the AIS MOB easyONE-DSCCL in an emergency, an AIS signal is generated which is received by all ships in the proximity that are equipped with an AIS receiver. This distress signal includes: • Current GPS/GNSS position information • Current COG and SOG • Text message “MOB ACTIVE” • Unique serial number of the device (MMSI) • Navigational Status 14 (AIS Search and Rescue Transmitter active) Usually the easyONE-DSCCL is displayed like an AIS S.
DSC Closed Loop Within seconds after the activation a first DSC alerting of all preprogrammed MMSI numbers is send out in closed loop mode. This transmission contains the unit ID of the distress transmitter, but no position information details because there is still no fix with the satellite. As soon as the position fix is established, a next DSC distress call in closed loop is transmitted to all (up to eight) numbers on the list with current position.
easyONE-DSCCL. After this broadcast this unit will fall back into DSC closed loop distress call automatically. Persistent AIS transmission will be done parallel. Red LED FLARE In event of triggering AIS and DSC emergency transmission, the strong red LEDs of the electronical safety FLARE start flashing within same clock rate as the white flash LEDs do. The FLARE will flash every 2 seconds. As longer the AIS MOB is in alert mode, the flashing time reduces but the intervall will stay at every 2 seconds.
7.2 TEST-Function (MOB TEST) Please check the transmitting function of the AIS MOB easyONE-DSCCL on a regular basis. An annual or semi-annual test is usually sufficient. Too frequent testing reduces battery capacity. The battery is designed for 7 years and more than 30 test activations. The antenna mechanism does not have to be triggered for the function test! Carrying out the test: • Leave the antenna rolled up inside the device.
On earlier systems, it appears as a ship symbol. The 9-digit “Unit-ID” (MMSI) of the easyONE-DSCCL, beginning with “972....” and a safety Message (SRM) “MOB TEST” are displayed and an audible and/or visual alarm is triggered. • In addition to the AIS telegrams, a DSC telegram is sent to the optionally programmed MMSI numbers. • The DSC transmission takes place immediately after switching on without position. AIS transmission with position only after position fix.
• At the end of test mode, before the unit is switching off automatically, the LEDs will display the test result: GPS-LED (10) display Test result GPS status LED glows The reception was OK. A position was determined. GPS status LED flashes No GPS/GNSS position could be determined within the first five minutes of testing time.
For more information about using the easyONE-DSCCL please visit our webpage (www.easyAIS.com). The current battery status of the easyONE-DSCCL can be read out also by the Weatherdock-App via Bluetooth®. Please keep the amount of Bluetooth connections only the bare necessities to go easy on power resources for event of emergency. 7.3 Deactivation (switching off the device) Deactivating the ON-Mode: Press the “ON” button (8) and the “TEST” button (7) at once for at least 3 seconds.
After downloading and installing the suitable app please follow the next working steps: • Press the TEST button for 3 seconds until the LEDs start flashing fast • The Bluetooth module needs up to 20 seconds to boot • After 20 seconds only the yellow LED is illuminated → Bluetooth is ready Weatherdock AG www.easyAIS.
• • • • • Seite 21 Please open the app on your mobile device If not activated, the App will ask for automatic activation of the BLUETOOTH® function. Tick “allow” in this case Tip on “scan for Device“, to connect the easyONE-DSCCL with your mobile device Tip on easyONE-DSCCL to select this kind of device This App is designed for the programming of the AIS SART unit easyRESCUE-PRO as well Weatherdock AG www.easyAIS.
• If the connection was not done automatically, tip to select manually • Click on “Load” • Information to the easyONEDSCCL will appeare Weatherdock AG www.easyAIS.
• On the back of the easyONEDSCCL you will find the unit ID of the device. Please check if the numbers are correct • If correct, please tip on the small right arrow to start programming the MMSI numbers Seite 23 Weatherdock AG www.easyAIS.
• The programming mask will start as displayed • Tip on one of the eight “ShipID” fields to enter there the ships MMSI • Enter the MMSI number you want to programm • Tip on “Programm” to store the number into the easyONEDSCCL Weatherdock AG www.easyAIS.
• Your entered number is stored. • The device will confirm with a yellow flashing LED • If you want to store more than one MMSI, please repeat the previous steps • This is an examplary programming of 4 different ship MMSI • If you entered a wrong number, just tip on that number to correct • All changes you do will be acknowledged by the yellow LED flashing after pressing “Programm” Seite 25 Weatherdock AG www.easyAIS.
• Sometimes you need to enter the same numbers into different easyONE-DSCCL units. • In event of such a case please tip on the “down” arrow • A list opens up with all MMSI numbers which had been programmed with this mobile device • Choose the number you need to programm Weatherdock AG www.easyAIS.
• If you want to delete the “frequently used MMSI” list out of the app (not on the easyONEDSCCL), please click on “X” and acknowledge with “YES” • If you want to delete a ship MMSI from the easyONEDSCCL, click on the number • Press “delete” • Every elimination will be confirmed by the yellow LED flashing Seite 27 Weatherdock AG www.easyAIS.
• Click on the left arrow to get back to main menu • The app’s starting window displays battery status of the device in addition • Click on “turn off” to shut down the easyONE-DSCCL • If you don’t switch off the easyONE-DSCCL by your own, 1 minute of inactivity will trigger self-shut-down functionality • The easyONE-DSCCL is now ready for usage in case of emergency Weatherdock AG www.easyAIS.
If there are too many Bluetooth activated devices like wearables, fitness trackers, etc. in the vicinity of the easyONE-DSCCL, they might cause problems with the connection establishment. In case of this please shut down the bluetooth function of your mobile device. Additionally please shut down all other bluetooth devices as well. After that, please start your mobile device again to connect with the easyONE-DSCCL to start programming.
Please also note our video instructions and the information on our website (www.easyais.com) Weatherdock AG www.easyAIS.
10 Maintenance and Service 10.1 Basic Antenna Position If the antenna mechanism of your easyONE-DSCCL should have been triggered unintentionally or you notice in the process of time that the water soluble pill starts breaking apart, you have the possibility to return your easyONE-DSCCL to original state. Therefore you’ll need a standard allen key (size 3mm) and a Secumar dissolvable activation pill from your specialist shop. Implementation: 1. Get the Allen key und spare pill ready. 2.
1. 2. 3. Weatherdock AG www.easyAIS.com 4. / 5.
7. 6. The overhaul of the trigger mechanism by a non-certified distributor or reseller is at your own risk! Only original spare pills are suited for replacement. Please also note our video tutorials and the reference information on our website (www.easyais.com) Seite 33 Weatherdock AG www.easyAIS.
10.2 Maintenance/Service Upon expiry, the batteries must be replaced by a specialist dealer. This is the only way to ensure 100 % functionality of the device for further use. 10.3 Cleaning In order to prevent damage to the plastic parts, use only a light damp cloth (no scouring agents and alkaline detergents or detergents containing acids or alcohol) to dust the product. 10.
Contact your local dealer for support. If the dealer may not be able to help, please contact our service department: Weatherdock AG Emmericher Strasse 17 D-90411 Nuernberg Phone: +49 (0)911-376638-30 Telefax: +49 (0)911-376638-40 E-Mail: info@weatherdock.de Internet: www.easyais.com 10.5 Disposal The AIS MOB easyONE-DSCCL uses lithium batteries. They shall not be given to household waste and must be given to the collection of recyclables. Seite 35 Weatherdock AG www.easyAIS.
11 Troubleshooting Please read the following tips for troubleshooting carefully. They might be vital if a problem occurs in an emergency situation! Fault Action Antenna does not unfold automatically Pull the alarm flap (4) with the seizing (9) off the device and press the antenna flap (3) counterclockwise with your hand outwards. The antenna (5) unfolds immediately. By pressing the “ON” button (8) you activate the distress signal manually.
The easyONE-DSCCL is jammed in the life jacket or between the life jacket and your body. Try to free the easyONE-DSCCL carefully. You can have the device floating beside you. The TEST mode cannot be activated. Please send the device immediately back to your dealer for service.
12 RESCUE Database and Login To increase functionality of AIS based personal locating beacons more safe and more effective, Weatherdock AG is providing a web-based database where customers can give additional relevant information. For more information about that service please look on our website: www.easyais.com or www.weatherdock.com On this webpage you can relate detailed personal data to your AIS MOB easyONE-DSCCL device. The details might be helpful for SAR organizations to save lifes.
On a voluntary basis, you can enter information concerning your boat and personal data, which are relevant for you as an owner of an easyONE-DSCCL. With your data you create an information platform which helps the emergency organization to do the right things - for example, in cases of diabetes or pharmaceutical intolerance. Beside you, only official authorities e.g. German„DGzRS“ or the British „UK Coast Guard“ will have access to your data.
13 License agreement By using the easyONE-DSCCL you agree to the following warranty agreement. Please read the agreement carefully. The Weatherdock AG grants a limited license for using the device for normal operation of the product. Name, property rights and intellectual property rights in and of the software remain with the Weatherdock AG. 14 Gewährleistung Warranty This Weatherdock product is warranted to be free from defects in materials or workmanship for 24 month from the date of purchase.
If you choose to use the easyONE-DSCCL in a boat, it is the sole responsibility of the owner/operator of the AIS MOB easyONE-DSCCL to secure the easyONE-DSCCL so that it will not cause damage or personal injury in the event of an accident. It is the sole responsibility of the operator of the boat to operate the boat in a safe manner, maintain full surveillance of all boating conditions at all times, and never become distracted by the easyONE-DSCCL to the exclusion of safe operating practices.
15 Specifications Description Value Dimension 195 * 50 * 30 mm Weight 120 grams Waterproof up to 10 meter depth Battery LiMn cells Bettery operating time 36 h at 0°C Battery lifetime 7 years Frequencies AIS: 161.975 MHz and 162.025 MHz DSC: 156.525 MHz Radiated power AIS: ≥ 1 Watt DSC: ≥ 0,5 Watt GPS/GNSS receiver 72 channel receiver with integrated antenna pursuant to IEC61108-1 VHF antenna foldout; rolled up in the device during inactive mode Display Controls Weatherdock AG www.
supported AIS messanges in transmission mode Message1 AIS position report 8x per minute Unit-ID (9 digits starting 972...) Speed over Ground (SOG) Course over Ground (COG) Message14 AIS safety related message (SRM) 2x every 4 minutes Unit-ID (9 digits starting 972...) Text: “MOB ACTIVE” in alert mode “MOB TEST” in test mode transmitted information in DSC mode Unit-ID (9 digits starting 972...
16 Personal Notes Weatherdock AG www.easyAIS.
Weatherdock AG Emmericher Strasse 17 D – 90411 Nuernberg Tel.: +49 (0) 911 – 37663830 Fax: +49 (0) 911 – 37663840 www.easyais.com info@weatherdock.de Seite 45 Weatherdock AG www.easyAIS.