Instructions / Assembly
45
44
888-745-0004 · weatherstrong.com · 888-745-0004 · weatherstrong.com ·
WEATHERSTRONG.COM
Toe Kick Application
Lay the trimmed toe kick panel in front of the cabinet against the leveling legs. Mark the
location of each leg on the back of the panel. Clips are not needed on all leg locations,
but enough for a secure hold.
Center the clip plates half way up the
height of the panel, screw into place.
Then slide a clip into each plate.
Align the panel and push the clips
onto the legs.
1
2 3
If applying toe kick around corners,
adjacent panels will clip to the same
corner leg. Be sure to stagger the clip
plate heights so they overlay properly.
WEATHERSTRONG.COM
Toe Kick Application
Lay the trimmed toe kick panel in front of the cabinet against the leveling legs. Mark the
location of each leg on the back of the panel. Clips are not needed on all leg locations,
but enough for a secure hold.
Center the clip plates half way up the
height of the panel, screw into place.
Then slide a clip into each plate.
Align the panel and push the clips
onto the legs.
1
2 3
If applying toe kick around corners,
adjacent panels will clip to the same
corner leg. Be sure to stagger the clip
plate heights so they overlay properly.
WEATHERSTRONG.COM
Toe Kick Application
Lay the trimmed toe kick panel in front of the cabinet against the leveling legs. Mark the
location of each leg on the back of the panel. Clips are not needed on all leg locations,
but enough for a secure hold.
Center the clip plates half way up the
height of the panel, screw into place.
Then slide a clip into each plate.
Align the panel and push the clips
onto the legs.
1
2 3
If applying toe kick around corners,
adjacent panels will clip to the same
corner leg. Be sure to stagger the clip
plate heights so they overlay properly.
WEATHERSTRONG.COM
Toe Kick Application
Lay the trimmed toe kick panel in front of the cabinet against the leveling legs. Mark the
location of each leg on the back of the panel. Clips are not needed on all leg locations,
but enough for a secure hold.
Center the clip plates half way up the
height of the panel, screw into place.
Then slide a clip into each plate.
Align the panel and push the clips
onto the legs.
1
2 3
If applying toe kick around corners,
adjacent panels will clip to the same
corner leg. Be sure to stagger the clip
plate heights so they overlay properly.
1. Lay the trimmed Toe Kick panel in front of the
cabinet against the Leveling Legs. Mark the location
of each Leg on the back of the panel. Clips are not
needed on all Leg locations, but enough for a secure
hold
2. Center the Clip Plates half way up the height of the
panel, screw into place. Then slide a Clip into each
Plate.
3. Align the Panel and push the clips onto the Legs
If applying Toe Kick around corners,
adjacent panels will clip to the same
corner Leg.
Be sure to stager the Clip Plate heights
so they overlay properly
TOE KICK APPLICATION
3 4
Stainless Steel Leveling Leg Assembly
Simple assembly is required for each leveling leg.
For easier handling and to avoid damage remove doors
and drawers from the cabinet. Then, using two or more
people, place the cabinet upside down on a protected surface.
Place the 2 front leg brackets 3-1/2" from
the front edge with the support plate
overlapping the end panel – 1/4" from the
outer edge.
1
Place the 2 back leg brackets 1" from
the back edge with the support plate
overlapping the end panel – 1/4" from
the outer edge.
2
Use a phillips bit to attach the legs
with the stainless steel screws supplied.
DO NOT OVERTIGHTEN!
Adjust the leveling legs up or down to
bring the cabinet to a level plumb position.
WEATHERSTRONG.COM
Leveling Leg Installation
3
1
/2 in
1
/4 in
from edge
1
/4 in
1in
LEVELING LEG INSTALLATION - STAINLESS LEGS
STAINLESS STEEL LEVELING LEG
ASSEMBLY
Simple assembly is required for each Leveling Leg
For easier handling and to avoid damage remove doors
and drawers from the cabinet. Then, using two or more
people, place the cabinet upside down on a protected
surface.
1. Place the 2 front leg brackets 3‑1/2" from the front
edge with the support plate overlapping the end
panel – 1/4" from the outer edge.
2. Place the 2 back leg brackets 1” from the back edge
with the support plate overlapping the end panel –
1/4" from the outer edge.
3. Use a Phillips bit to attach the legs with the stainless
steel screws supplied. DO NOT OVERTIGHTEN!
4. Adjust the leveling legs up or down to bring the
cabinet to a level plumb position.
3 4
Stainless Steel Leveling Leg Assembly
Simple assembly is required for each leveling leg.
For easier handling and to avoid damage remove doors
and drawers from the cabinet. Then, using two or more
people, place the cabinet upside down on a protected surface.
Place the 2 front leg brackets 3-1/2" from
the front edge with the support plate
overlapping the end panel – 1/4" from the
outer edge.
1
Place the 2 back leg brackets 1" from
the back edge with the support plate
overlapping the end panel – 1/4" from
the outer edge.
2
Use a phillips bit to attach the legs
with the stainless steel screws supplied.
DO NOT OVERTIGHTEN!
Adjust the leveling legs up or down to
bring the cabinet to a level plumb position.
WEATHERSTRONG.COM
Leveling Leg Installation
3
1
/2 in
1
/4 in
from edge
1
/4 in
1in
3 4
Stainless Steel Leveling Leg Assembly
Simple assembly is required for each leveling leg.
For easier handling and to avoid damage remove doors
and drawers from the cabinet. Then, using two or more
people, place the cabinet upside down on a protected surface.
Place the 2 front leg brackets 3-1/2" from
the front edge with the support plate
overlapping the end panel – 1/4" from the
outer edge.
1
Place the 2 back leg brackets 1" from
the back edge with the support plate
overlapping the end panel – 1/4" from
the outer edge.
2
Use a phillips bit to attach the legs
with the stainless steel screws supplied.
DO NOT OVERTIGHTEN!
Adjust the leveling legs up or down to
bring the cabinet to a level plumb position.
WEATHERSTRONG.COM
Leveling Leg Installation
3
1
/2 in
1
/4 in
from edge
1
/4 in
1in
3 4
Stainless Steel Leveling Leg Assembly
Simple assembly is required for each leveling leg.
For easier handling and to avoid damage remove doors
and drawers from the cabinet. Then, using two or more
people, place the cabinet upside down on a protected surface.
Place the 2 front leg brackets 3-1/2" from
the front edge with the support plate
overlapping the end panel – 1/4" from the
outer edge.
1
Place the 2 back leg brackets 1" from
the back edge with the support plate
overlapping the end panel – 1/4" from
the outer edge.
2
Use a phillips bit to attach the legs
with the stainless steel screws supplied.
DO NOT OVERTIGHTEN!
Adjust the leveling legs up or down to
bring the cabinet to a level plumb position.
WEATHERSTRONG.COM
Leveling Leg Installation
3
1
/2 in
1
/4 in
from edge
1
/4 in
1in
3 4
Stainless Steel Leveling Leg Assembly
Simple assembly is required for each leveling leg.
For easier handling and to avoid damage remove doors
and drawers from the cabinet. Then, using two or more
people, place the cabinet upside down on a protected surface.
Place the 2 front leg brackets 3-1/2" from
the front edge with the support plate
overlapping the end panel – 1/4" from the
outer edge.
1
Place the 2 back leg brackets 1" from
the back edge with the support plate
overlapping the end panel – 1/4" from
the outer edge.
2
Use a phillips bit to attach the legs
with the stainless steel screws supplied.
DO NOT OVERTIGHTEN!
Adjust the leveling legs up or down to
bring the cabinet to a level plumb position.
WEATHERSTRONG.COM
Leveling Leg Installation
3
1
/2 in
1
/4 in
from edge
1
/4 in
1in
3 4
Stainless Steel Leveling Leg Assembly
Simple assembly is required for each leveling leg.
For easier handling and to avoid damage remove doors
and drawers from the cabinet. Then, using two or more
people, place the cabinet upside down on a protected surface.
Place the 2 front leg brackets 3-1/2" from
the front edge with the support plate
overlapping the end panel – 1/4" from the
outer edge.
1
Place the 2 back leg brackets 1" from
the back edge with the support plate
overlapping the end panel – 1/4" from
the outer edge.
2
Use a phillips bit to attach the legs
with the stainless steel screws supplied.
DO NOT OVERTIGHTEN!
Adjust the leveling legs up or down to
bring the cabinet to a level plumb position.
WEATHERSTRONG.COM
Leveling Leg Installation
3
1
/2 in
1
/4 in
from edge
1
/4 in
1in