Instructions / Assembly

47
46
888-745-0004 · weatherstrong.com · 888-745-0004 · weatherstrong.com ·
1. Lay the trimmed Toe Kick panel in front of the
cabinet against the Leveling Legs. Mark the location
of each Leg on the back of the panel. Clips are not
needed on all Leg locations, but enough for a secure
hold
2. Center the clips half way up the height of the toe kick
panel, screw into place. Then screw the clip directly
onto the toe kick panel.
3. Align the Panel and push the clips onto the Legs
If applying Toe Kick around corners,
adjacent panels will clip to the same
corner Leg.
Be sure to stager the Clip Plate heights
so they overlay properly
TOE KICK APPLICATION
WEATHERSTRONG.COM
Toe Kick Application
Lay the trimmed toe kick panel in front of the cabinet against the leveling legs. Mark the
location of each leg on the back of the panel. Clips are not needed on all leg locations,
but enough for a secure hold.
Center the clips half way up the height of
the toe kick panel, screw into place. Then
screw the clip directly onto the toe kick panel.
Align the panel and push the clips
onto the legs.
1
2 3
If applying toe kick around corners,
adjacent panels will clip to the same
corner leg. Be sure to stagger the clip
heights so they overlay properly.
WEATHERSTRONG.COM
Toe Kick Application
Lay the trimmed toe kick panel in front of the cabinet against the leveling legs. Mark the
location of each leg on the back of the panel. Clips are not needed on all leg locations,
but enough for a secure hold.
Center the clips half way up the height of
the toe kick panel, screw into place. Then
screw the clip directly onto the toe kick panel.
Align the panel and push the clips
onto the legs.
1
2 3
If applying toe kick around corners,
adjacent panels will clip to the same
corner leg. Be sure to stagger the clip
heights so they overlay properly.
WEATHERSTRONG.COM
Toe Kick Application
Lay the trimmed toe kick panel in front of the cabinet against the leveling legs. Mark the
location of each leg on the back of the panel. Clips are not needed on all leg locations,
but enough for a secure hold.
Center the clips half way up the height of
the toe kick panel, screw into place. Then
screw the clip directly onto the toe kick panel.
Align the panel and push the clips
onto the legs.
1
2 3
If applying toe kick around corners,
adjacent panels will clip to the same
corner leg. Be sure to stagger the clip
heights so they overlay properly.
WEATHERSTRONG.COM
Toe Kick Application
Lay the trimmed toe kick panel in front of the cabinet against the leveling legs. Mark the
location of each leg on the back of the panel. Clips are not needed on all leg locations,
but enough for a secure hold.
Center the clips half way up the height of
the toe kick panel, screw into place. Then
screw the clip directly onto the toe kick panel.
Align the panel and push the clips
onto the legs.
1
2 3
If applying toe kick around corners,
adjacent panels will clip to the same
corner leg. Be sure to stagger the clip
heights so they overlay properly.
REQUIRED TOOLS
• Level
• Plastic Shims (for leveling if necessary)
• Drill
• Tapcon 3/16” x 2-3/4” Stainless Steel Screws
• 1/4” Stainless Steel Washers
• Tapcon 3/16” Drill Bit (pilot holes in concrete -
typically is provided with screws)
• 3/16” Wood Drill Bit (pilot holes in cabinet backs or
installation rails)
• 1/8” Wood Drill Bit (pilot holes in cabinets sides to
join them together)
• Phillips Head Screwdriver
• Clamps (with rubber pads)
• Saw (circular or table) – to trim matching end panels
and toe kick fillers
• Carpenter’s Square
• Tape Measure
• Extension Cord
• Step Ladder (at least 6’ if installing wall cabinets)
LEVELING THE CABINETS
Leveling the cabinets is the most important part
of installation, to ensure doors align properly and
countertop sets evenly. They are to be level and square.
Make sure your leveling legs are installed and adjusted.
Review separate leveling leg instructions.
Be sure to level your cabinets in all three
directions:
1. Front to Back
2. Vertically
3. Horizontally
INSTALLATION GUIDE
1
2
3
BEFORE YOU BEGIN:
Check your new cabinetry against your design plan to
ensure that you have all required cabinets, moldings,
llers, and accessories to complete the installation.
SAFETY FIRST:
To avoid injury, explosion, or shock, make sure that
all water supplies, gas supplies, and pertinent circuit
breakers are shut off. Double check electrical using
circuit tester to conrm power is off. If you are uncertain
that utilities have been properly shut off, consult your
utility company or service professional.
CAUTION:
It is essential that you use the recommended screws
for your cabinetry installation. Under no circumstances,
should you use nails or drywall screws as they do not
have the strength or holding power to ensure that
cabinets stay on the wall. Failure to use specied screws
will render warranty null and void.
Installation detailed in this manual is for concrete block
construction only. Attachment to any other wall types,
will require locating the wood or steel studs behind the
wall. Consult with your local home center, hardware
store or installation specialist for recommended
fasteners.