Instructions / Assembly

55
54
888-745-0004 · weatherstrong.com · 888-745-0004 · weatherstrong.com ·
CARE AND USE GUIDE
AFTER INSTALLATION CARE
After your cabinets have been installed, wipe down all
exteriors with a damp cloth to remove dust.
Clean Up: Wash WeatherStrong with water and a soft
cloth or sponge. A mild dishwashing liquid can be used
if needed. For tougher to clean spots, wash with Simply
Green All-Purpose Household Cleaner. A soft bristle
brush may be used if needed.
EVERYDAY CARE
Salt Water Environments: Oceanfront environments with
salt air and sea spray will require regular maintenance
and cleaning to prevent rust from forming on the
handles, hinges and drawer runners. Clean stainless
steel surfaces several times a month to keep the
chemical reaction, from the salt, from gaining a foothold
on the hardware. With regular cleaning, your cabinets
will look like new for many years. To achieve maximum
corrosion and stain resistance, the surface of the
stainless steel must be kept clean.
NEVER use abrasive cleaners, scouring pads or
powdered cleansers.
HARDWARE CARE
Use mild soap and warm water to clean door, drawer
knobs and pulls. Thoroughly dry hardware surfaces after
cleaning. DO NOT use silver or brass polish.
DRAWER REMOVAL
STEP 1
Fully open drawer
and remove
contents.
STEP 4
To re-install, align
drawer slides and
gently push drawer
closed. Locking
tabs do not need
to be pressed.
STEP 2
With drawer fully
opened locate slide
tab on left side of
drawer box and
push up to release.
STEP 5
Open and close
drawer several
times to ensure
proper alignment.
STEP 3
Locate slide tab
on the right side
of drawer box
and push down to
release.
GRILL & SIDE BURNER CABINET MODIFICATIONS
Grill and side burner cabinets are manufactured with two
full upper face plates that will need to be eld modied
to accept the respective insulated jacket used with the
gas grill or side burner.
The second matching panel will be shipped loose for
ease of modication and installation. It can be attached
with stainless steel screws or a suitable construction
grade adhesive. Under no circumstance should a grill
or side burner be installed without the appropriate heat
liner specied by the manufacturer of the appliance.
HEAT APPLIANCES
Free-standing grills with adequate space from direct
heat are recommended or grills with insulated jacket
specied by the grill manufacturer can be installed in
WeatherStrong cabinets.
Insulated jackets are required for heat admitting
appliances being installed in WeatherStrong
LIGHT EXPOSURE
Cabinet sides and backs that will be exposed to direct
sunlight and other weather elements MUST be covered
by a matching end panel in coordinating High Density
Polyethylene (HDPE). Failure to install these protective
panels will void the cabinet warranty.
CARE AND USE GUIDE
In a standard base
cabinet there is a
location on the inside
for the roll-out tray.
Indicated by the two
sets of pre-drilled holes
on the back panel.
STEP 4
Roll-out tray is
installed.
STEP 3
Push to lock in
place.
STEP 2
Once the desired area
is reached on both
sides attach the roll-
out tray on the left and
right.
STEP 1
Put the roll-out tray
at the desired area in
the base cabinet and
pick the same desired
height on the opposite
side.
ROLL-OUT TRAY RELOCATION/INSTALLATION
DOOR POSITION ADJUSTMENT
HEIGHT
Loosen two screws
and adjust door to
desired position.
Re-tighten all
screws.
HEIGHT
For vertical door
adjustment loosen
center screw on each
hinge. Set door at
desired height. Re-
tighten each screw.
DEPTH
Using a Phillips
screwdriver, rotate
back screw to move
the door to the
desired position.
DEPTH
Rotate back screw
for front to back door
adjustment
SIDE TO SIDE
Using a Phillips
screwdriver, rotate
front screw to move
the door to the
desired position.
SIDE TO SIDE
Rotate front screw
for horizontal door
adjustment