Installation & Operation Manual KIT P/N: 300101 and 300202
Installation / Operation Manual Seat Comfort Contents Contents.................................................................................................................................. 3 Warnings: ................................................................................................................................ 4 Notice To Users Of Carbotex Seat Heating Systems:............................................................... 5 Safety Advice:.............................................
Installation / Operation Manual Seat Comfort Warnings: Carbotex aftermarket Seat Heater Systems are not designed as a “do-it-yourself“ installation products! To enhance safety and assure a high level of electrical contact of wires, simple cable/wire connectors (squeeze type splicing, etc.) cannot be used in this installation. All connections must be soldered and properly insulated afterwards. Always consult the vehicle wiring diagram when unsure about individual wire/power source identification.
Installation / Operation Manual Seat Comfort Notice To Users Of Carbotex Seat Heating Systems: The seat heater is designed to control the temperature of the lower and upper seat segment of the front seats. Proper temperature control of the vehicle seat increases the driver‘s comfort and enhances your basic health. The seat heater operates in two power levels and can only be engaged with the ignition turned on.
Installation / Operation Manual Seat Comfort Disclaimer The installation instructions must be followed with utmost diligence by trained and properly qualified specialists as failures to comply (or mistakes during the installation phase) may cause damage to the system, the vehicle and may potentially impose harm to drivers and/or passengers.
Installation / Operation Manual Seat Comfort Introduction Carbotex after market seat heater systems are ideal comfort additions to the front seat of every vehicle. Soon after the driver and passenger have experienced the advantages of a seat heating device, the accessory will be used and valued year round and not only during the cold winter month.
Installation / Operation Manual Seat Comfort Installation Steps 1 Removal of seat Secure the vehicle on a level and plane parking area. Remove the front seat that the seat heater is to be installed. Refer to the vehicle manufacturers recommended service procedure for proper removal of seat. 2 Preparation for the electrical wire connection Disconnect the battery prior to any activities with the vehicle wiring system. Follow the vehicle manufacturer guidelines when disconnecting the battery.
Installation / Operation Manual 5 Seat Comfort Electrical connection (Rectangle Switch Only) Mount the seat heater switch in a convenient location. Position the switch so that the marking “HI“ faces to the front of the installation. Positive power connection: Connect the positive wire to an ignition power source. Note: Make absolutely certain that the vehicle electric and power lay out can support the seat heater power requirements. If necessary, utilize a relay.
Installation / Operation Manual 8 Seat Comfort Electrical connection Positive power connection: The connection is always to the ignition positive power. Note: Make sure that the vehicle electrical system can support the seat heater power requirements. Firmly solder the red wire from the seat heater harness to the vehicle wire/connector. Assure proper insulation of the connector area.
Installation / Operation Manual 11 12 13 14 Seat Comfort Position the heating pad with the label facing down and the wire harness facing towards the rear of the vehicle seat. Adjust the pad in a way that the safety thermo protector incorporated in the heating pad is located approx. 2-5 cm forward of the back rest.
Installation / Operation Manual 15 16 17 Seat Comfort Insulate the lateral "bridges", which protrude out from the previously cut area, with the supplied black insulation tape. Assure proper insulation. Position the heating pads on the foam seat pad. Assure that the insulated segments of the seat heater pads align with the grooves in the foam cushion. The heating pad must not overlay the side seems.
Installation / Operation Manual 19 Seat Comfort For safety reasons you should protect those danger spots with suitable material (i.e. insulation tape or shrinkable hose) Careful not to damage seat heater when reinstalling upholstery clamps. Run the harness from the seat heater pads in a way that it exits the seat to prevent harness exposure. Use same procedures when running wires and harnesses (seat heater pad upper back rest segment) from the back rest of the seat.
Installation / Operation Manual Seat Comfort Technical Assistance If you require help, check our technical assistance website at http://www.techwebasto.com or call the technical support hotline at (800) 860-7866.
Installation / Operation Manual Seat Comfort Limited Warranty Webasto carries a 3 year or 36,000 miles driven limited warranty beginning from the date of installation. The warranty covers proven fabrication and materials deficiencies.
Webasto Product N.A., Inc. Technical Assistance Hotline Phone: (800) 860-7866 www.webasto.us www.techwebasto.