Owner manual

DT313C/ DT313C-MD/ DT313H/ DT313H-MD
ENGLISH
4
OPERATION
Internal Baery
Warning!
!
The Internal baery pack should only be replaced by an authorized DT Research service
representave. Please contact your product and/or service provider for internal baery
replacement service.
Powering ON and OFF
To acvate the DT313C/ DT313C-MD/ DT313H/ DT313H-MD, push and quickly release
the Power Buon. The display will come on in a few seconds. To put the DT313C/
DT313C-MD/ DT313H/ DT313H-M
D in Standby mode, push and quickly release the
Power Buon. To turn the DT313C/ DT313C-MD/ DT313H/ DT313H-MD off for extended
storage, power off safely using any soware funcon that
“
shuts down computer
”
provided in the soware operang system.
NOTE:
The baery packs shipped with your tablet may be low in power
—
please use
the AC-DC adapter with the DT313C/ DT313C-MD/ DT313H/ DT313H-MD when
seng up
for the first me to fully charge the internal baery pack. You may
charge the external baery pack with it aached to the DT313C/ DT313C-MD/
DT313H/ DT313H-MD, or with the oponal external baery charger kit.
NOTE:
When the baery pack(s) is (are) charging, the blue-colored Baery LED should
blink slowly. If plugging in the AC-DC adapter does not trigger this blinking
acvity and the LED stays dar
k, the baery pack(s) may have been drained
substanally. Try unplugging/ replugging the AC-DC adapter to the DT313C/
DT313C-MD/ DT313H/ DT313H-MD a few mes to acvate the charging
process.
NOTE:
To conserve power, use (push and quick release) the Power Buon to put the
tablet in
“
Standby
”
mode while not in use. Pushing briefly on the same buon
will wake up the system within seconds.
NOTE:
Avoid
using the Power Buon (
“
hold 4+ seconds
”
feature) to turn off the
tablet
—
this form of hardware shutdown is intended to be a means of recovery
from lockups, and not as normal operaon.
5
ENGLISH
Start Up
If the power up (from Standby or otherwise) is successful, the appropriate interface will
be displayed aer a launch sequence of several seconds. The wireless LAN connecon
may take 10-15 seconds to be estab
lished.
Configuring the Mobile Tablet
The DT313C/ DT313C-MD/ DT313H/ DT313H-MD may be configured using the ulies
and methods dictated by the soware operang system. The DT313C/ DT313C-MD/
DT313H/ DT313H-MD should be configurable for various properes such as user
profiles, network features, and several system elements.
Wireless Networking
Wireless LAN
The DT313C/ DT313C-MD/ DT313H/ DT313H-MD is oen delivered with an embedded
(user-inaccessible) 802.11a/b/g/n WLAN adapter equipped with a hidden custom
antenna.
Through the support of typical WLAN adapters, the DT313C/ DT313C-MD/ DT313H/ •
DT313H-MD should be able to detect all 802.11 access points in the vicinity for you to
select the access point of your choice for connecon.
The SSID and WEP/WPA/WPA2 (if enabled) parameters on the DT313C/ DT313C-MD/ •
DT313H/ DT313H-MD and the access points have to match. The SSID is case-sensive
and it is recommended that you enable WEP/WPA/WPA2 encrypon (or advanced
alternaves) for secure access.
When WEP/WPA/WPA2 is enabled, you may need to consult your network •
administrator or your networking equipment literature to properly configure
associated sengs such as Authencaon mode, etc.
Refer to
the access point operang manuals for seng up the 802.11 access points.•