Serial Number Please use this number in registering your warranty and any correspondence with the factory. PLATINUM 3400 Series ™ LP Gas Barbecue Owner's Manual ® National PROPANEGAS Association WARNING: Follow all leak check procedures carefully in this manual prior to barbecue operation. Do this even if barbecue was dealer assembled. NOTICE TO INSTALLER: These instructions must be left with the owner and the owner should keep them for future use.
DANGER Failure to follow the Dangers, Warnings and Cautions contained in this Owner’s Manual may result in serious bodily injury or death, or in a fire or an explosion causing damage to property. WARNINGS Do not store a spare or disconnected LP tank under or near this barbecue. Improper assembly may be dangerous. Please carefully follow the assembly instructions in this manual.
WARRANTY Weber-Stephen Products Co. (Weber) hereby warrants to the ORIGINAL PURCHASER of this Weber Gas Barbecue that it will be free of defects in material and workmanship from the date of purchase as follows: There are no other express warrants except as set forth herein and any applicable implied warranties of merchantability and fitness are limited in duration to the period of coverage of this express written Limited Warranty.
PATENTS AND TRADEMARKS © 1997 Weber. Weber, , Flavorizer and Crossover are registered U.S. trademarks; Platinum, Per ma-Mount, Gas Catcher, FlameCheck, Steam-N-Chips, Spider Stopper, and Warm-Up are U.S. trademarks of Weber-Stephen Products Co., 200 East Daniels Road, Palatine, IL 60067-6266. U.S.A. Printed in the U.S.A.
Contents WARNINGS ................................................................ 2 Warranty & Patents.................................................. 3-4 General Instructions.................................................... 6 Assembly ............................................................... 7-27 Troubleshooting & Maintenance Annual Maintenance ........................................ 35 General Maintenance.................................. 36-38 Troubleshooting ...............................
General Instructions Storage Your Weber Gas Barbecue is a portable outdoor cooking appliance. With the Weber Gas Barbecue you can grill, barbecue, roast and bake with results that are difficult to duplicate with indoor kitchen appliances. The closed lid and Flavorizer Bars produce that "outdoor" flavor in the food. The Weber Gas Barbecue is portable so you can easily change its location in your yard or on your patio. Portability means you can take your Weber Gas Barbecue with you if you move.
Assembly Step 1 Check package contents Tools needed Screwdrivers, regular Cooking box (assembly) and Phillips Hammer Lid (assembly) 7/16, 5/8, 11/16 and 3/4 inch open-end or two adjustable wrenches ® ® Pliers LP tank Block of wood Supplies needed Filler adapter Your LP tank is shipped empty for safety. After setting the LP fuel scale you will need to fill it. (See Step "Fill LP tank"). You will need a soap and water solution to check for gas leaks. (See Step “Check for gas leaks”).
Work table Left frame Wheel frame Two swing tables Tank panel assembly 1 Panels and doors are identified with removable stickers. Please leave on during assembly.
Left hand slide bar assembly Manifold bracket Assembly consists of: Two cooking grates Left hand slide bar Eight short Flavorizer Bars Support rod Catch pan holder Slide Catch pan Two drip pans Right hand slide bar assembly Two casters Assembly consists of: Right hand slide bar Fuel scale Support rod Thermometer Slide Side burner assembly Burner grate Side burner knob Two side burner locks 9
Five 1/4-20 x 2 inch bolts (actual size) Check contents of hardware packs Four 10-24 x 1 3/4 inch machine screws (actual size) 1/4-20 x 1 1/2 inch bolt (actual size) Twenty-three 1/4 inch nylon washers (actual size) Six 1/4-20 x 1/2 inch bolts (actual size) Four 10-24 hex nuts (actual size) Two 1/4-20 wing nuts (actual size) Three burner control knobs 1/4-20 keps nut Three tool holders 1/4-20 hex nut (actual size) Four tubing plugs (two are spares) Two hair pin cotters Two swing table end brackets Two
Step 3 Assemble wheels Assemble frame You will need: axle, two wheel hubcaps, two wheels, wheel frame, hammer and a block of wood. You will need: left frame, right frame, two nylon washers, two 1/4-20 x 1/2 inch bolts and a 7/16 inch wrench. Place one end of the axle on the block of wood (or other protected surface). Tap on one hubcap. Note - Work on carpeted area (on grass, or on one of the boxes) to protect the finish during frame assembly. Put one wheel on the axle, WEBER side toward the hubcap.
Step 4 Step 5 Continue frame assembly Complete frame assembly You will need: frame assembly, wheel frame assembly, front panel, caster frame, four 1/4-20 x 1/2 inch bolts, four nylon washers and a 7/16 inch wrench. You will need: partial frame assembly, one frame connector with bushings, one frame connector without bushings, four 1/4-20 x 2 inch bolts, four nylon washers and a 7/16 inch wrench. Place the caster frame onto the tabs of the left frame with the dimple to the inside. Figure 3.
Step 6 Step 8 Insert casters Install left end panel You will need: frame assembly and two casters. You will need: frame assembly and left end panel. (Number 1) Push the casters firmly into the caster inserts in the ends of the caster legs. Figure 5. Place the bottom of the left end panel on the caster frame lower cross piece. Set the end panel upright in place. Figure 7.
Step 9 Step 10 Install the three back panels Install side burner locks You will need: frame assembly, two plastic buttons and the three back panels. (Number 2) You will need: frame assembly, two side burner locks and a 7/16 inch wrench. Place the bottom of one back panel on the back frame connector, notches to the top. Set in place to the far left, butting up against the caster frame. Repeat the procedure with the the other two back panels. Figure 8. Loosen the right rear 1/4 x 20 bolt.
Step 11 Your Weber Gas Barbecue burner assembly has been factory assembled, pressure and flame tested. As a safety precaution we recommend you check the burner alignment: Add cooking box You will need: frame assembly, cooking box assembly, spacer bracket, 1/4-20 x 2 inch bolt, nylon washer, 1/4-20 keps nut, pliers and a 7/16 inch wrench. a) Do the valves fit into the ends of the burners? Figure 13 (a).
Step 12 Step 13 Install side burner Install manifold bracket You will need: side burner assembly, burner grate, and manifold bracket. You will need: manifold bracket Hook the bracket onto the manifold at the center burner valve. Figure 15. Place your hand underneath the bracket. Lift the bracket, manifold and cooking box slightly as a unit and hook onto the frame brace. WARNING: Make sure gas supply is OFF. Slide the side burner assembly into the open end of the right frame.
Step 14 Step 15 Install tank panel assembly Install right end panel You will need: tank panel assembly. You will need: right end panel (Number 3), 1/4-20 x 1 1/2 inch bolt, 1/4-20 hex nut, two nylon washers and a 7/16 inch wrench. Slide the side burner back. Insert the tabs into the slots in the frame brace at the wheel legs. (Make sure the side burner hose is to the front of the barbecue.) Figure 16 (a). Slide up until the notch at the bottom of the tank panel fits over the cross brace.
Step 16 Step 18 Add fuel scale Install igniter You will need: fuel scale assembly, two 1/4-20 wing nuts and two nylon washers. Note - The igniter wires are already attached to the Gas Catcher Ignition Chamber and the igniter. This was done to factory test the ignition system. Insert indicator rod of fuel scale through the elongated hole in the right end panel. Figure 18 (a). The igniter lock nut is on the igniter. Route the igniter and wires as shown. Figure 20 (a).
Step 19 Insert one end of the hinge rod into the hole in the frame. Figure 23 (a). Check that all burner valves are off Insert the other end into the hole in the swing table end bracket. Figure 23 (b). Hold the end bracket at an angle so the lower tab is inside the frame tube. Push the bracket into the frame. Check to see that the lower tab of the bracket is hooked in the slot in the frame. Figure 23 (c). You will need: one burner control knob.
Step 21 Position slide bar assembly on the outside of the caster frame. Put a nylon washer on each 1 3/4 inch screw, insert screws through frame and slide bar assembly and add nylon washers and hex nuts. Tighten nuts using a screwdriver and pliers. Figure 24. Install right hand swing table You will need: swing table end bracket, two 10-24 hex nuts, two 10-24 x 1 3/4 inch machine screws, right hand slide bar assembly, swing table, four nylon washers, screwdriver and pliers.
Insert one end of the hinge rod into the hole in the frame. Figure 27 (a). Position slide bar assembly on the outside of the wheel frame. Put a nylon washer on each 1 3/4 inch screw, insert screws through frame and slide bar assembly and add nylon washers and hex nuts. Tighten nuts using a screwdriver and pliers. Figure 28. Insert the other end into the hole in the swing table end bracket. Figure 27 (b). Hold the end bracket at an angle so the lower tab is inside the frame tube.
Step 22 To fill, take the LP tank and filler adapter to an RV center or look up gas-propane in the phone book for other sources of LP gas. Set LP fuel scale You will need: LP tank (empty). WARNING: We recommend that your LP tank be filled at an authorized LP gas dealer by a qualified attendant, who fills the tank by weight. Note - For accuracy, the fuel scale must be set with an empty tank. IMPROPER FILLING IS DANGEROUS. We utilize various LP tank manufacturers.
Step 25 The hose and regulator are connected in the following manner: Check for gas leaks Slide back the collar of the quick disconnect on the tank valve. Push the male fitting of the regulator into the quick disconnect, and maintain pressure. Slide the collar closed. Figure 32 (a). Figure 32 (b) shows the quick disconnect engaged and various components of the tank and regulator. Regulator vent hole should be at 3, 6, or 9 o'clock. It should not be pointed up. Figure 32 (c).
Check: Step 26 a) Hose to manifold connection. Figure 35 (a). Install Flavorizer Bars and Cooking Grates b) Regulator to tank connection. Figure 35 (b). c) Manifold to side burner hose connection. Figure 35 (c). You will need: five long Flavorizer Bars, eight short Flavorizer Bars and two cooking grates. WARNING: If there is a leak at connections a, b or c, retighten the fitting and recheck for leaks with soap and water solution.
Step 27 Step 28 Install the bottom tray Install the lid You will need: bottom tray, catch pan holder, catch pan and one drip pan. You will need: lid, two hinge pins and two hair pin cotters. Set the lid in place. Align the hinges at the rear of the barbecue. Insert hinge pins from the outside. Insert hair pin cotters into the small holes in the hinge pins. Figure 41.
Step 29 Step 30 Install tool holders, control panel and burner control knobs Secure the side burner Pull the right hand swing table up. Stand to the right side of the barbecue. Slightly pull back both side burner locks. Slide the side burner toward the control panel. The locks will snap into the slots in the front and back of the side burner. Figure 43. You will need: three tool holders, control panel, two Phillips screws/washers, a Phillips screwdriver, and three burner control knobs.
Step 31 Step 32 Install glass doors Complete accessory installation You will need: one LH glass door assembly and two RH glass door assemblies. You will need: work table, Warm-Up Basket, warming rack, thermometer, two tubing plugs and a hammer. Start with the LH door assembly. Insert the long hinge pin at the top of the door into the plastic bushing in the underside of the left frame. Insert the bottom (short) hinge pin into the bushing in the frame connector.
OPERATING INSTRUCTIONS WARNING: The burner control knobs must be in the OFF position before turning on the LP tank valve. If they are not in the OFF position, when you turn on the LP tank valve, the excess flow control will activate, limiting the flow of gas from the LP tank. If this should occur, turn OFF the LP tank valve and burner control knobs and start over. Lighting Summary lighting instructions are on the control panel.
Manual Lighting 4) Turn the tank on by turning the tank valve counterclockwise. DANGER 5) Strike a match and put the flame into the matchlight hole in the front of the cooking box. Failure to open lid while igniting the barbecue, or not waiting 5 minutes to allow the gas to clear if the barbecue does not light, may result in an explosive flame-up which can cause serious bodily injury or death. WARNING: Do not lean over open barbecue.
Lighting the side burner Lighting the side burner if the main burners are lit. Figure 4. The side burner has a separate ignition system from the main cooking box. 1) Open the side burner lid. 2) Push down and turn the side burner control to HI. DANGER 3) Press the side burner igniter button several times so it clicks each time.
Cooking Storage and/or Nonuse continued WARNING: Do not move the Weber Gas Barbecue when operating or hot. You can adjust the FRONT, CENTER and BACK burners as desired. The control settings High (H), Medium (M), Low (L), or Off (O) are described in your Weber cookbook. The cookbook uses these notations to describe the settings of the FRONT, CENTER, and BACK burners. For example, to sear steaks you would use (HHH) (all burners at high).
Refilling the LP tank Connecting the filled LP tank WARNING: Make sure that the LP tank valve is closed. Close by turning clockwise. We recommend that you refill before the scale indicator reaches "E". DANGER Note - If you run out of fuel, check the indicator setting and/or adjust the fuel scale indicator setting with the scale setting wing nut while the tank is empty so you do not run out again. Do not use an open flame to check for gas leaks.
c) Connect the hose to the tank. Slide back the collar of the quick disconnect on the tank valve. Figure 7 (a). Push the male fitting of the regulator into the quick disconnect, and maintain pressure. Slide the collar closed. Figure 7 (b). If it does not engage or lock, repeat procedure. Gas will not flow unless the quick disconnect is properly engaged. f) Check for leaks by wetting the fitting with the soap and water solution and watching for bubbles. If bubbles form or if a bubble grows there is a leak.
Safe handling tips for LP Gas ■ Liquid Propane (LP) Tank(s) Liquid Propane (LP) gas is a petroleum product as are gasoline and natural gas. LP gas is a gas at regular temperatures and pressures. Under moderate pressure, inside a tank, LP gas is a liquid. As the pressure is released the liquid readily vaporizes and becomes gas. ■ LP gas has an odor similar to natural gas. You should know this odor. ■ LP gas is heavier than air. Leaking LP gas may collect in low areas that prevent dispersion.
WARNING: If there is a leak at connections a, b or c, retighten the fitting and recheck for leaks with soap and water solution. Annual Maintenance After a period of nonuse we recommend that you perform the following maintenance procedures for your safety. If a leak persists after retightening the fitting, turn OFF the gas. DO NOT OPERATE THE BARBECUE. Contact your dealer. WARNING: Check hose before each use of barbecue for nicks, cracking, abrasions or cuts.
General Maintenance Main Burner Flame Pattern Weber Spider Stopper Guards The Weber Gas Barbecue burners have been factory set for the correct air and gas mixture. The correct flame pattern is shown in Figure 13. Your Weber Gas Barbecue, as well as any outdoor gas appliance, is a target for spiders and other insects. They can nest in the venturi section of the burner tubes. This blocks the normal gas flow, and can cause the gas to flow back out of the air shutter. Figure 11.
d) Unlatch the Spider Stopper Guards and remove. Figure 16. g) Lift and twist the burner assembly slightly, to separate the crossover tube from the burners. Figure 19. Remove the burners from the cooking box. Crossover tube Figure 16 Figure 19 e) Remove the manifold bracket and unscrew the two wing nuts that hold the manifold to the cooking box. Pull the manifold and valve assembly out of the burners and carefully set it down. Figure 17. h) To reinstall burners, reverse steps c) through g).
i) Crossover Ignition System Operations Reinstall the Spider Stopper Guards. Slightly rotate the Spider Stopper Guards so that the seams are in line with the Venturi fins. There should be no gaps in the seams or in the fit around the burners and valves. Figure 21. If the Crossover Ignition System fails to ignite the Front burner, light the Front burner with a match. If the Front burner lights with a match, then check the Crossover Ignition System.
TROUBLESHOOTING Problem Check Cure Burners burn with a yellow or orange flame, in conjunction with the smell of gas. Inspect Weber Spider Stopper Guards for possible obstructions. (Blockage of holes.) Clean Weber Spider Stopper Guards. (See Section "Annual Maintenance".) Burners do not light. -orBurners have a small flickering flame in the HIGH position. -orBarbecue temperature only reaches 250˚ to 300˚ degrees in the HIGH position.
Side Burner Troubleshooting WARNING: Before attempting any troubleshooting steps, all gas controls and supply valves should be in the OFF position. Problem Check Cure Side burner does not light. Is gas supply off? Is the Front burner on? Turn supply on. Light front burner. Flame is low in HIGH position. Is fuel hose bent or kinked? Straighten hose. Flame is very yellow in conjunction with the smell of gas, Inspect the Weber Spider Stopper Guard for possible obstructions. (Blockage of holes.
1 43 44 ® ® 45 2 3 46 47 48 4 5 6 49 50 51 52 7 53 54 8 9 10 11 12 55 2 56 2 57 2 13 14 58 15-16 1 59 60 61-64 17 18-20 65-66 21 22 3 23 24 25 13 14 LH RH 26 RH W 27 E BE R 67 W 68 E BE R 28 29 30 31 32 33 34 35 36 37 42 38 38 39 40 41 42
Parts List While we give much attention to our products, unfortunately an occasional error may occur. If a part is missing, do not go back to the store. Call the Weber Customer Service Center toll free 1-800-446-1071 to receive immediate assistance. Have your owner’s manual and serial number of the barbecue available for reference. All items are single quantities unless otherwise specified. Purchase parts and accessories from your dealer.
A FINAL WORD OF THANKS Thank you for choosing a Weber Barbecue. Our family here at Weber has worked hard to produce the highest quality products for your satisfaction. While we give much attention to our products, an occasional error may occur. Our knowledgeable Customer Service staff is prepared to help you with any problems with parts or assembly. Call our toll free number 1-800-446-1071. For quicker service, please have your owner’s manual available for reference.