Gas Go Anywhere ® 55014 02/23/01
FOR OUTDOOR USE ONLY This grill does not include an LP fuel tank. Check Package Contents You should have received the parts listed below. While we give much attention to out product, unfortunately an occasional error may occur. If a part is missing, do not go back to the store. Call WeberStephen Products Customer Service Center toll free 1-800-446-1071 to receive immediate assistance.
1 - Leg Lock 1 - 1/4-20 wing nut 1 - 5/16” Washer 1 - 1/4-20 x 1/2 bolt 2 - 10-24 screws 2 - 10-24 wing nuts 6 - 1/4” Flat washers 1 - Igniter 3
Install Legs Place washers on leg ends and insert ends into holes in bottom unit. Be careful not to scratch the porcelain finish while installing the legs. Repeat with other leg. Install Leg Lock Position curved end of leg lock at corner of the straight portion of the leg, as shown. Push until it snaps on. 1 2 3 Position legs and secure leg lock Swing legs around so that the rounded part sets on the ground and the bottom of the cooking box rests on the straight part of the legs.
Install Burner Tube From the inside, insert burner tube through the large hole in the side of the bottom unit. Line up the other end of the tube with the hole. Insert the 1/2 inch bolt. Add the washer and wing nut. Tighten. Install Regulator Remove the retaining clip from the regulator. Attach regulator assembly by inserting the brass fitting into the end of the burner tube.. Secure regulator assembly by installing the retaining clip in the square openings on both sides of the burner tube.
Install Igniter Insert the igniter electrode and two 10-24 screws through the igniter bracket and the holes in the bottom unit on the side opposite the regulator. Add washers and wing nuts, making sure that the wing nuts are secured in a vertical position. The igniter electrode has been pre-bent. It may need to be adjusted so the tip is approximately 1/8 inch from the holes in the burner tube. DANGER Make sure the tip of the igniter wire is adjusted to the holes in the burner tube.
Install Flavorizer Bar Place the Flavorizer Bar in bottom unit, covering the burner. Install Cooking Grate Set the cooking grate onto the recessed edge of the bottom unit. To Secure for Transport Put the lid on the bottom unit unlock legs and pivot them into the locked position up over the projections on the lid.
To Use Pivot legs under grill and lock legs. The hooks on the inside of the lid allow it to rest on the edge of the bottom unit. ® Read important DANGERS, WARNINGS and CAUTIONS in Owner’s Guide before operating this barbecue. Connecting the Cylinder 1. Lubricate the threads of the regulator assembly with petroleum jelly. 2. Make sure the burner control valve is in the LOCK/OFF position before attaching the propane cylinder. Valve closes by turning the knob clockwise to the LOCK/OFF position. 3.
Check for Gas Leaks DANGER Do not use an open flame to check for gas leaks. Be sure there are no sparks or open flames in the area while you check for leaks. This will result in a fire or explosion which can cause serious bodily injury or death, and damage to property. 1. Check the connection between the tank and the regulator for gas leaks. Mix a couple of tablespoons of liquid detergent with an equal amount of water. 2. Be sure to leave the burner control valve in the LOCK/OFF position.
Manual Lighting 1. Light a match and hold it in one of the four holes in the bottom of the grill. 2. Push down burner control valve and turn counter-clockwise to HIGH. 3. Check to see if the burner is lit by looking through the viewing hole in the Flavorizer Bar. WARNING: If burner does not light, turn burner control valve OFF, wait 5 minutes for the gas to clear, then try again. Gas Grill Care While lid is warm, wipe inside with paper towels to prevent grease build-up.
1 2 3 8 9 10 11 12 13 4 14 15 5 16 17 18 19 6 7 1-3. Handle 4. 10-24 Wing Nuts 5. Retaining Clip 6. Regulator Assembly 7. Leg Lock 8. Lid 9. Cooking Grate 10. Flavorizer Bar 11. Bolt 12. 13. 14. 15. 16. 17. 18. 19.
© 1999 Weber-Stephen Products Co., Weber, the silhouette, and the kettle configuration are registered trademarks of WeberStephen Products Co., 200 East Daniels Road, Palatine, IL, 60067-6266, U.S.A. This product is covered by one or more United States patents and patents in other nations globally. Printed in the U.S.A.
