1. Check Frame rate setting based on power frequency - Set Frame rate to 25Hz if your region is using 50Hz(PAL) power frequency, or set to 30Hz for 60Hz(NTSC) region. (OSD : System Frame rate). 2. Focus setup To aviod losing focus at night time, please adjust camera focus as follows. 1) Move Tele, Wide to adjust Zoom and Near, Far to adjust Focus. 2) Press joystick shortly to activate Auto focusing. 3) If no further action during 5sec, adjust focusing mode will be closed automatically.
Feature HD-SDI video digital signal HD-SDI(High Definition Serial Digital Interface) is non-compressed digital signal for broadcasting, and there is no quality loss of high definition images. 2MP, Full HD high resolution picture quality Full HD(1920x1080) provides 6 times higher resolution than SD level camera, and more clear video image can be achieved through 1/3”, 2Megapixel progressive CMOS.
Supplied accessories Please check if all the supplied accessories are included. Camera Installation / User Manual Monitoring Cable(IR18) Hood Screw Iron Screw L Wrench C1080BL-IR48-AF Hood C1080BL-IR18-AF Hood Product description No Name 1 Camera 2 Camera Hood 3 RS485 Port 4 Power input connector 5 Video output BNC connector Camera installation Auto Iris connector wiring We recommend to use ‘Adjust Focusing’ mode for camera focusing.
※ To get fine focusing, video will be zoomed twice in Adjust Focusing mode. Notice for Auto Focus operation Following conditions might make failure of auto focusing . 1. When there are changes of the scene while Auto Focus is working(sudden movement, appearance or disappearance). 2. When there are sudden change of the brightness. 3. When shooting low contrast image. 4. When there is strong light in the scene. 5. When there is foreign substance on the lens. 6.
2. Configure PTZ settings such as Protocol(C1080), Baudrate, Address in DVR. 3. Run HD Camera Upgrade program then enter IP address of DVR which is connected to camera and enter channel number of camera. - PC for Firmware upgrade and DVR need to be connected with network. - HD Camera Upgrade program and firmware can be downloaded from Webgate’s website. 4. Select a Firmware and click Load button. Then firmware upgrade will proceed and the camera will reboot automatically after completion.
- D&N AF : Autofocusing after Day&Night chages DAY Color Maintains Color(Day) mode regardless brightness. & NIGHT B&W Maintains B&W(Night) mode regardless brightness. Auto In accordance with brightness, camera switches Color mode and B&W mode automatically. - LUX LEVEL(LOW, MIDDLE, HIGH) : This value is the standard for Day & Night switching. If high is selected, camera will turn to Night(B/W) mode at higher LUX level than MIDDLE or LOW.
KELVIN, R-GAIN and B-GAIN value. CHROMA Adjust Chroma level. (10, 0~20) IMAGE SHARPNESS (5, 0~10) Adjust sharpness. The higher value will show more clear video image H-MIRROR Mirror image. Left and right will be reversed V-MIRROR Flip image. Up and down will be reversed. Digital ZOOM Zoom image by 16 steps.
(ON, OFF) brightness of dark areas. DNR Reduce image noise under low light condition (LOW, MIDDLE, HIGH) FRAMERATE (25Hz, 30Hz) SYSTEM Power frequency 60Hz(NTSC) : 30Hz(fps) video output Power frequency 50Hz(PAL) : 25Hz(fps) video output MODEL Displays model name CAM ID Max. 8 digits for camera name. Supports alphanumeric and some special characters RS485 ID Set ID for RS485 VERSION Displays firmware version RESOLUTION Set output resolution (1080p/720p).
Video Control Distance approx.
Dimension (unit : mm) C1080BL-IR18-AF C1080BL-IR-48-AF 10
How to upgrade C1080 Series Camera through DVR 1. Check F/W version of DVR and Camera. - Camera : Over v1.2.x (System Version info. v1.0.x doesn’t support remote upgrade) - DVR : Over v3.9.30 - Control Center : Over v2.26.x 2. Connect Com2/Com3(RS-485) port of DVR with RS-485 of C1080 camera. - GND need to be connected as well as + , - when connect RS-485. - Use twist pair cable in case the distance between DVR and Camera is far(over 5m).
button. 1) User doesn’t need to enter port number even though connected DVR has specific port. Just enter IP address of DVR. 2) Select correct F/W per model. Otherwise camera might not show correct display. - C1080B : C1080B_v1.xx.x.bin - C1080BM : C1080BM_v1.xx.x.bin - C1080D Series(D,VD,D-IR,VD-IR) : C1080VD_v1.xx.x.bin - C1080AF Series(D-AF,D-IR-AF,VD-AF,VD-IR-AF,BL-IR18-AF,BL-IR48-AF) : C1080AF_v1.xx.x.bin 3) The upgrade time via Network will be various based on environment and Baudrate.
7. Camera OSD menu is activated when click Camera Setup menu and there will be control window at the right bottom side of the screen. 1) The possible delay could be occurred during menu control based on network situation. 2) Make single channel in DVR then click PTZ button of DVR then it will be same as control in C.C (Control Center). 3) ESC button is not used.
8. Please pay attention while F/W upgrade into the latest version and F/W upgrade with wrong F/W will make camera work abnormally. Please refer to below classified table to check F/W version. 1) Directions for upgrade of camera + If the camera is upgraded with wrong F/W, camera will not be working normally. + C1080B/BM model can be upgraded with the latest F/W regardless of mechanical part and lens. + Please upgrade B type after checking lens.
B type Classification By mechanical part F/W Classification Non AF Series : C1080VD_v1.14.0 a type b type By lens F/W AF Series C1080AF_v1.13.
