Instruction manual

※ Please read instruction manual carefully before
installing or using this product.
OPT-RX1-RS485U / OPT-TX1-RS485U
OPT-RX16-RS485U / OPT-TX4-RS485U
Instruction Manual
The World’s first certified by
HDcctv Alliance
Precautions
Coax Cable
1. HD-SDI maximum transmission distance depends on
the cable manufacturer or installation environment.
2. The impedance of the coaxial cable and BNC
connectors must be 75 Ohm. For your reference, please
refer to the below table of cable recommendation.
Note) When selecting a cable, consider the maximum
transmission distance of the cable which depends on
its attenuation at 750MHz.
(dB/100m <25dB of attenuation is recommended.)
Cable Type
Length of
HD-SDI
Details of usage
5C2V
About
100M
For analog signal
4C-FB(T), 4C-HFB(T),
About
150M
5C-FB(T), 5C-HFB(T),
L-6CHD, RG6
About
200M
Dedicated cable for HD-SDI
Note) Foamed or High-foamed insulation cable is
recommended.
Note) Double or Triple shielded cable is recommended
Trouble Shooting
EN Rev 1.0
WEBGATE Div. Daemyung Enterprise Co., Ltd.
6F, Hanlim Venture Town B/D, 689-6, Geumjeong-Dong
Gunpo-Si, Gyeonggi-do, Korea
TEL : [phone]
FAX : [phone]
[e-mail]
[e-mail]
www.webgateinc.com
Premium to your HD-CCTV solution
Device connection method
1. Connect camera’s video output to Transmitter’s “HD-SDI In” using coaxial cable.
- To control camera OSD or PTZ, connect RS485 line between Transmitter and camera.
- Please refer to “NOTICE of coaxial cable” regarding the maximum transmission distance of HD-SDI.
2. Connect Transmitter and Receiver using Single mode LC Type fiber-optic cable.
- When connecting optical cable to the converter, insert fully until you hear a click sound.
- As shown in Figure 1, pull the lever to lock the optical cable not to fall off from the converter.
3. Connect Receiver’s “HD-SDI Out” to DVR’s “HD-SDI In” using coaxial cable.
- To control camera OSD or PTZ, connect RS485 line between Receiver and DVR.
4. Check the status of LED indicators to confirm the correct connections
- Power : Red LED will be lit if the power is on.
- HD-SDI : Green LED will be lit if the video signal enters.
- Optic : Green LED will be lit if Transmitter and Receiver are connected each other.
- RS485 : Green LED will be blinking during data is being entered.
5.Check the monitor that is connected to DVR whether all channels are properly displayed
FIBER OPTIC CONVERTER
Fiber-Optic Cable
1. For cable connection, do not bend the
cable narrower than 30mm
(Minimum allowable refraction range).
2. Do not pull the cable from both ends.
3. Do not spin the optical cable while the
cable is connected to connector.
4. Do not knot the optical cable.
Specification
DVR
Receiver
TransmitterCamera
Fiber Optic Cable
Max. 20Km
Product Features
1. Converting between HD-SDI signal and Optical signal.
Optical signal transmission.
2. Video/Data (RS485) transmission up to 20Km through
single mode fiber-optic cable.
3. Supports 1.5Gbps, 750Mbps for optical signal, and
max. 115200bps for data.
4. Supports 1080p25/30 or 1080i50/60 video.
5. LED indicators for Power, Video, Data and Fiber-optic
Status.
6. 1U 19” rack type (OPT-RX16-RS485U model only).
7. Advanced surge arrestor and ESD protection circuit for
HD-SDI port.
RS485
HD-SDI
Refer to picture No.1
Refer to
picture No.1
RS485
HD-SDI
Picture No.1
LC Type Connector
Accessories
※ Power cord and adapter are supplied only for
OTP-RX4-RS485U and OPT-RX16-RS485U
Trouble & Symptom Way to Solve
Can not turn on the
equipment, and LED
indicators do not work.
√ Check the power is properly
connected to the equipment
√Check the input power voltage
√ If it does not work, please check
the power adapter or replace it
Nothing shows on the
screen.
Can not control camera’s
OSD menu and PTZ
√Check the RS485 connection
among camera, converter and
DVR
√ Check the polarity of RS485(+,-)
√ Check the setting of DVR and
camera. If the setting values such
as Baudrate, Protocol, Address are
not properly configured, camera
control can not be achieved..
Model OPT-RX1-RS485U OPT-TX1-RS485U OPT-TX4-RS485U OPT-RX16-RS485U
Function 1Ch Receiver 1Ch Transmitter 4Ch Transmitter 16Ch Receiver
Video Standard
Resolution
Impedance
Fiber Optic Type
Connector
HD-SDI Length
Fiber Length
Data Channel
Indicator LED
Input Voltage/Current
Operating Temperature / Humidity
Power consumption Max 6.0W Max 30W
Dimension (W x D x H) 140 X 239 X 54 mm 361 X 483 X 44 mm
Weight
Certifications
12 VDC
(Acceptable Input Voltage Range 6V ~ 25V)
HD-SDI SMPTE 292M
SMPTE 274M(1080p25/30, 1080i50/60), SMPTE 296M(720p25/30/50/60)
75 ohm
Single-mode
LC
Approx 150m@L-4CFB(Canare)
Approx 20Km at 1.5Gbps
RS485 Upstream(Remote control from DVR to Camera)
Power(Red), Link-Opt(Green), Link-SDI(Green), RS485(Green)
KC, FCC, CE, RoHS, HDcctv(TBD)
Max 2.0W
65 X 117 X 26 mm
+0°C to +50°C (+32°F to +122°F) 20%RH to 80%RH
※ ※
1Ch TX/RX 4Ch TX 16Ch RX
Installation Power Cable Adapter
Accessories
Fiber Optic Converter
160g 150g 1Kg 4.5Kg
High-foamed, double or
triple shielded cable is
recommended
RG59
√Check video of camera that is
connected to Transmitter. If there
is no video output from camera,
nothing could be shown on the
screen
√Check the power connection of
camera
√Check the cable connections
between camera, converter and
DVR