A WILSON ELECTRONICS BRAND DRIVE 4G-M Vehicle Signal Booster Kit User Manual NEED HELP? support.weboost.com 866.294.
______ Index Package Contents 1 STEP 1: Mount Outside Magnetic Antenna 2 STEP 2: Mount Inside Antenna 4 STEP 3: Connect Coax Cables To Booster 5 STEP 4: Connect Power Supply To Booster 6 STEP 5: Plug Power Adapter Into Vehicle’s Power Supply 7 Light Patterns 8 Troubleshooting 9 Safety Guidelines 10 Specifications 11 Warranty 12
________ Package Contents Booster Outside Antenna Inside Antenna Power Supply Optional: Adhesive disk for aluminum vehicles DRIVE 4G-M VEHICLE SIGNAL BOOSTER 1
______ Step 1: Mount Outside Magnetic Antenna Identify a location on the top of your vehicle that is: • Near the center of the roof • At least 12 inches away from any other antennas • At least 6 inches away from any windows (including sunroofs) Clean the surface where you will place the outside antenna. Mount the outside antenna by placing on top of vehicle. 6 in. away from windows (including sunroofs) NOTE: For aluminum roofs, use the included adhesive disk to secure outside antenna in place.
______ (STEP 1 cont.) See options below on how cable can be routed with different vehicles. NOTE: The cable is strong enough that it may be shut in most vehicle doors without damaging the cable. Car/Sedan: Cable routed into rear side door. NOTE: When going through car wash, remember to remove your antenna. SUV/Van/Hatchback: Cable routed into top of hatchback door. Truck: Cable routed into side door.
______ Step 2: Mount Inside Antenna Identify a place to mount the 4G In-Vehicle Antenna, either on the side of the seat or on the dash and mount. The location should be at least 18 inches but no more than 36 inches from where the cellular device will be used. Use the Velcro® adhesive strip/adhesive strip provided and attach to desired location.
______ Step 3: Connect Coax Cables To Booster Connect the cable from the Mini-Mag Mount Antenna to the port labeled “Outside Antenna” on the Drive 4G-M booster. POW ER OUTS ANTE IDE NNA from Outside Antenna Connect the cable from the 4G In-Vehicle Antenna to the port labeled “Inside Antenna” on the booster.
______ Step 4: Connect Power Supply To Booster Connect the power supply cord to the end of the Drive 4G-M labeled “Power.” NOTE: Do NOT connect the power to the Signal Booster until you have connected both the Inside and Outside Antennas.
______ Step 5: Plug Power Adapter Into Vehicle’s Power Supply Plug the power adapter into vehicle’s 12V DC power supply. Power up your Drive 4G-M by flipping the switch on the back of the DC power adapter on. If your Drive 4G-M is working correctly, the light on the power adapter will be red, and the light on the booster will be green. DC Power Adapter NEED HELP? support.weboost.com DRIVE 4G-M VEHICLE SIGNAL BOOSTER 866.294.
______ Light Patterns Solid Green This indicates that your booster is functioning properly and there are no issues with installation. Green/Red Blinking This indicates that one or more of the booster bands has reduced power due to a feedback loop condition called oscillation. This is a built in safety feature to prevent harmful interference with a nearby cell tower. If you are already experiencing the desired signal boost, then no further adjustments are necessary.
______ Troubleshooting FIXING BLINKING OR SOLID RED ISSUES This section is only applicable if the booster is red or blinking red and you are not experiencing the desired signal boost. 1 Unplug the Booster’s power supply. 2 Relocate the inside and outside antenna further from each other. The objective is to increase the separation distance between them, so that they will not create this feedback condition discussed before. 3 Plug power supply back in. 4 Monitor the indicator light on your booster.
______ Safety Guidelines Use only the power supply provided in this package. Use of a non-weBoost product may damage your equipment. All inside panel and dome antennas must have at least 6’ of separation distance from all active users, and low profile antennas must have at least 1.5’ separation distance from all active users. Connecting the Signal Booster directly to the cell phone with use of an adapter will damage the cell phone.
______ Specifications Drive 4G-M Product Number U470008 Model Number 460021 FCC ID: PWO460021 IC: 4726A-460021 Connectors SMA-Female Antenna Impedance Frequency 50 Ohms 698-746 MHz, 746-787 MHz, 824-894 MHz, 1850-1995 MHz, 1710-1755/2110-2155 MHz Maximum Power Power output for single cell phone (Uplink) dBm 700 MHz Band 12/17 18.0 700 MHz Band 13 20.0 800 MHz Band 5 19.4 1700 MHz Band 4 18.3 1900 MHz Band 2 21.4 Power output for single cell phone (Downlink) dBm 700 MHz Band 12/17 2.
2 YEAR WARRANTY weBoost Signal Boosters are warranted for two (2) years against defects in workmanship and/or materials. Warranty cases may be resolved by returning the product directly to the reseller with a dated proof of purchase. Signal Boosters may also be returned directly to the manufacturer at the consumer’s expense, with a dated proof of purchase and a Returned Material Authorization (RMA) number supplied by weBoost. weBoost shall, at its option, either repair or replace the product.
Notes NEED HELP? support.weboost.com DRIVE 4G-M VEHICLE SIGNAL BOOSTER 866.294.
3301 East Deseret Drive, St. George, UT 866.294.1660 www.weboost.com support.weboost.com Copyright © 2017 weBoost. All rights reserved. weBoost products covered by U.S. patent(s) and pending application(s) For patents go to: weboost.com/us/patents NOT AFFILIATED WITH WILSON ANTENNA GDE000065_Rev02_05.2.