Ceramic Cooktop Instruction Manual / Installation Manual Model ：WECF-A213
Safety Warnings Your safety is important to us. Please read this information before using your cooktop. Installation Electrical Shock Hazard • Disconnect the appliance from the mains electricity supply before carrying out any work or maintenance on it. • Connection to a good earth wiring system is essential and mandatory. • Alterations to the domestic wiring system must be only made by a qualified electrician. • Failure to follow this advice may result in electrical shock or death.
installation. • This appliance is to be properly installed and earthed only by a suitably qualified person. • This appliance should be connected to a circuit which incorporates an isolating switch providing full disconnection from the power supply. • Failure to install the appliance correctly could invalidate any warranty or liability claims. Operation and Maintenance Electrical Shock Hazard • Do not cook on a broken or cracked cooktop.
• Metallic objects such as knives, forks, spoons and lids should not be placed on the hob surface since they can get hot. • Keep children away. • Handles of saucepans may be hot to touch. Check saucepan handles do not overhang other cooking zones that are on. Keep handles out of reach of children. • Failure to follow this advice could result in burns and scalds. Cut Hazard • The razor-sharp blade of a cooktop scraper is exposed when the safety cover is retracted.
• Do not allow children to play with the appliance or sit, stand, or climb on it. • Do not store items of interest to children in cabinets above the appliance. Children climbing on the cooktop could be seriously injured. • Do not leave children alone or unattended in the area where the appliance is in use. • Children or persons with a disability which limits their ability to use the appliance should have a responsible and competent person to instruct them in its use.
hazard. •This appliance is intended to be used in household and similar applications such as: -staff kitchen areas in shops, offices and other working environments; -farm houses; -by clients in hotels, motels and other residential type environments; -bed and breakfast type environments. •WARNING: The appliance and its accessible parts become hot during use. Care should be taken to avoid touching heating elements. Children less than 8 years of age shall be kept away unless continuously supervised.
•WARNING: Danger of fire: do not store items on the cooking surfaces. • Warning: If the surface is cracked, switch off the appliance to avoid the possibility of electric shock, for hob surfaces of glass-ceramic or similar material which protect live parts •A steam cleaner is not to be used. •The appliance is not intended to be operated by means of an external timer or separate remote-control system. CAUTION: The cooking process has to be supervised.
Congratulations on the purchase of your new Hob. We recommend that you spend some time to read this Instruction / Installation Manual in order to fully understand how to install correctly and operate it. For installation, please read the installation section. Read all the safety instructions carefully before use and keep this Instruction / Installation Manual for future reference. Product Overview Top View 1. max. 1800 W zone 2. max. 1200 W zone 3. 2200/1000 W zone 4. max. 1200 W zone 5. Glass plate 6.
A Word on Ceramic Cooktop •Ceramic hob cooking is based on infrared heating technology, the nickel chrome wires of the hob would radiate heat and give out the infrared to warm up the food. The ceramic cooker hob centers on customers and adopts personalized design. The hob has safe and reliable performances, making your life comfortable and enabling to fully enjoy the pleasure from life. •Ceramic hobs do not pick pot.
Using the Touch Controls • • • • The controls respond to touch, so you don’t need to apply any pressure. Use the ball of your finger, not its tip. You will hear a beep each time a touch is registered. Make sure the controls are always clean, dry, and that there is no object (e.g. a utensil or a cloth) covering them. Even a thin film of water may make the controls difficult to operate.
3. Select a heating zone by touching the “-” or“+”control of the zone you choose 4. Select a heat setting by touching the “-” or “+” control. • If you don’t choose a heat setting within 1 minute, the induction hob will automatically switch off. You will need to start again at step 1. • You can modify the heat setting at any time during cooking. • By holding down either of these buttons, the value will adjust up or down. When you have finished cooking 1.
4. Beware of hot surfaces “H” will show which cooking zone is hot to touch. It will disappear when the surface has cooled down to a safe temperature. It can also be used as an energy saving function if you want to heat further pans, use the hotplate that is still hot. Using dual zone This cooktop has dual zone(for zone 3#), the power will rise to 2200W when activate the dual zone. 1. Touch the “-” or “+” of heating zone 3# (the right rear zone). 2. Activating dual zone by pressing 3.
When the hob is in the lock mode, all the controls are disable except the ON/OFF , you can always turn the ceramic hob off with the ON/OFF control in an emergency, but you shall unlock the hob first in the next operation Over-Temperature Protection A temperature sensor equipped can monitor the temperature inside the ceramic hob. When an excessive temperature is monitored, the ceramic hob will stop operation automatically.
2. Touch the “-” or “+” controls of the timer control, the timer indicator will flash. 3. Adjust the timer setting by touch the “-“or “+” controls. The minute minder indicator will start flashing and will show in the timer display. Hint: Touch the “-“ or “+” control of the timer once to decrease or increase by 1 minute. Touch and hold the “-“or ”+” control of the timer to decrease or increase by 10 minutes. If the setting time exceeds 99 minutes, the timer will automatically return to 0 minute. 4.
6. Buzzer will beep for 30 seconds and the timer indicator shows “- - “ when the set time finished. Setting the timer to turn one cooking zone off 1. Touch the “-” or “+” control of the heating zone for and the timer indicator will flash that you want to set the timer 2. Set the time by touching the “-” “+”control of the timer Hint: Touch the “-“or “+” control of the timer once will decrease or increase by 1 minute.
4.When the time is set, it will begin to count down immediately. The display will show the remaining time and the timer indicator flash for 5 seconds. NOTE: The red dot next to power level indicator will illuminate indicating that zone is selected. Setting the timer to turn more than one cooking zone off 1. If more than one heating zone use this function, the timer indicator will show the lowest time. (e.g.
Cooking Guidelines Cooking Tips • When food comes to the boil, reduce the power setting. • Using a lid will reduce cooking times and save energy by retaining the heat. • Minimise the amount of liquid or fat to reduce cooking times. • Start cooking on a high setting and reduce the setting when the food has heated through. Simmering, cooking rice • Simmering occurs below boiling point, at around 85˚C, when bubbles are just rising occasionally to the surface of the cooking liquid.
Heat Settings Heat setting 1-2 3-4 Suitability • • • • • • • delicate warming for small amounts of food melting chocolate, butter, and foods that burn quickly gentle simmering slow warming reheating rapid simmering cooking rice 5-6 • pancakes 7-8 • sauteing • cooking pasta 9 • • • • stir-frying searing bringing soup to the boil boiling water Care and Cleaning What? How? Important! Everyday soiling on glass (fingerprints, marks, stains left by food or non-sugary spillovers on the glass) 1.
Boilovers, melts, and hot sugary spills on the glass Spillovers on the touch controls Remove these immediately with a fish slice, palette knife or razor blade scraper suitable for ceramic glass cooktops, but beware of hot cooking zone surfaces: 1. Switch the power to the cooktop off at the wall. 2. Hold the blade or utensil at a 30° angle and scrape the soiling or spill to a cool area of the cooktop. 3. Clean the soiling or spill up with a dish cloth or paper towel. 4.
The touch controls are difficult to operate. The glass is being scratched. Some pans make crackling or clicking noises. There may be a slight film of water over the controls or you may be using the tip of your finger when touching the controls. Rough-edged cookware. Make sure the touch control area is dry and use the ball of your finger when touching the controls. Unsuitable, abrasive scourer or cleaning products being used.
L(mm) W(mm) H(mm) D(mm) A(mm) B(mm) X(mm) 770 520 52 48 560 490 50 mini Under any circumstances, make sure the ceramic cooker hob is well ventilated and the air inlet and outlet are not blocked. Ensure the ceramic cooker hob is in good work state. As shown below Note: The safety distance between the hotplate and the cupboard above the hotplate should be at least 760mm.
A(mm) B(mm) C(mm) D E 760 50 mini 30 mini Air intake Air exit 10 mm Before locating the fixing brackets The unit should be placed on a stable, smooth surface (use the packaging). Do not apply force onto the controls protruding from the hob. Fix the hob on the work surface by screw four brackets on the bottom of hob (see picture) after installation. A B C D screw bracket Screw hole base Cautions 1. The ceramic cooker hob must be installed by qualified personnel or technicians.
2. The ceramic cooker hob shall not be mounted to cooling equipment, dishwashers and rotary dryers. 3. The ceramic cooker hob shall be installed such that better heat radiation can be ensured to enhance its reliability. 4. The wall and induced heating zone above the work surface shall withstand heat. 5. To avoid any damage, the sandwich layer and adhesive must be resistant to heat. 6. A steam cleaner is not to be used. 7. This ceramic can be connected only to a supply with system impedance no more than 0.
2. If the appliance is being connected directly to the mains supply, an omnipolar circuit breaker must be installed with a minimum gap of 3mm between the contacts. 3. The installer must ensure that the correct electrical connection has been made and that it complies with safety regulations. 4. The cable must not be bent or compressed. 5. The cable must be checked regularly and only replaced by a properly qualified person.
