User Documentation

ManualsBrandsWeidmueller ManualsB2CF 3.50/180FB2CF 3.50/04/180F SN OR BX

We reserve the right to make technical changes.00/03.16

Assembly instructions

PUSH IN spring connection – plug-in connector B2CF 3.50

OMNIMATE Signal – series B2CF 3.50/180

All other technical data can be obtained from the data sheet

Cables suitable for connection:

Strip the insulation from the cables to a length of approx. 10mm ±1mm, even if you are using wire-end ferrules. If you use wire-end ferrules with plastic collars,

strip the cables according to the table below.

min. cable connection cross-section max. cable connection cross-section

Solid (H05(07) V-U) 0.14 mm² 1.5 mm²

Flexible (H05(07) V-U) 0.14 mm² 1.5 mm²

with wire-end ferrule according to DIN 46 228/1 0.25 mm² 1.5 mm²

with wire-end ferrule; with collar DIN 46 228/4 0.25 mm² 1.0 mm²

*1; *2

AWG 26 18

*1: Restriction for max. wire cross-section: crimp shape according to European standard EN 60947-1. We recommend the following crimping tools:

– Crimping tool for wire-end ferrule of 0.25 mm² to 1.5 mm² with trapezoidal indentation crimp, type PZ6/5 (Order No. 9011460000)

– Crimping tool for wire-end ferrule of 0.14 mm² to 0.75 mm² with trapezoidal crimp, type PZ1.5 (Order No. 9005990000)

*2: Please use wire-end ferrules according to the table below

We recommend using the following wire-end ferrules:

Cable diameter Type Weidmüller colour code

Order number

DIN colour code

Order number

Stripping length

1.00 mm² H1.0/18 9025930000 9019110000 15 ±1 mm

0.75 mm² H0.75/18 9025910000 9019060000 15 ±1 mm

0.50 mm² H0.5/16 9025870000 9019020000 12 ±1 mm

0.34 mm² H0.34/12 9025770000 10 ±1 mm

0.25 mm² H0.25/12 9025760000 10 ±1 mm

0.14 mm² H0.14/12 9028240000 10 ±1 mm

Examples of crimp shape according to European standard EN 60947-1:

Summary of content (4 pages)

PAGE 1
Assembly instructions PUSH IN spring connection – plug-in connector B2CF 3.50 OMNIMATE Signal – series B2CF 3.50/180 All other technical data can be obtained from the data sheet Cables suitable for connection: Strip the insulation from the cables to a length of approx. 10 mm ± 1 mm, even if you are using wire-end ferrules. If you use wire-end ferrules with plastic collars, strip the cables according to the table below.
PAGE 2
PUSH IN connector design: slider / push-button / pusher Handling: Recommended tool: • Screwdriver blade 0.4 x 2.5 • Screwdriver blade standard DIN 5264 conductor entry end stop spring clamp Solid conductors: 1. A stripped solid conductor is simply plugged into the contact point up to the end stop. Conductors with wire-end ferrule: 1. Stranded conductors with crimped-on wire-end ferrules, with and without plastic collars, are simply plugged into the contact point up to the end stop.
PAGE 3
Montageanleitung PUSH IN Federanschluss – Steckverbinder B2CF 3.50 OMNIMATE Signal – Serie B2CF 3.50/180 Alle weiteren technischen Daten sind dem Datenblatt zu entnehmen. Anschließbare Leiter: Isolieren Sie die Leitungen auf einer Länge von ca. 10 mm ±1 mm ab, auch wenn Sie Aderendhülsen verwenden. Wenn Sie Aderendhülsen mit Kunststoffkragen verwenden, isolieren Sie die Leitungen gemäß unten stehender Tabelle ab.
PAGE 4
Aufbau Push In Steckverbinder: Schieber / Push-Button / Pusher Handling: Leitereinführung Empfohlenes Werkzeug: • Schraubendreherklinge 0,4 x 2,5 • Schraubendreherklinge Norm DIN 5264 Anschlag Klemmfeder Starre Leiter: 1. Ein abisolierter starrer Leiter wird einfach, bis zum Anschlag, in die Klemmstelle gesteckt. Leiter mit Aderendhülse: 1. Mehrdrähtige Leiter mit aufgecrimpten Aderendhülsen, mit und ohne Kunststoffkragen, werden einfach, bis zum Anschlag, in die Klemmstelle gesteckt.