Document of Conformity

ManualsBrandsWeidmueller ManualsBLZP 5.08HC/180BLZP 5.08HC/06/180 AU GR BX

Test Report issued under the responsibility of:

TEST REPORT

IEC 61984

Connectors – Safety requirements and tests

Report Number..............................:

2198607.50

Date of issue .................................:

2017-02-21

Total number of pages..................:

Applicant’s name ..........................:

Weidmüller Interface GmbH & Co. KG

Address .........................................:

Klingenbergstraße 16, D-32758 Detmold, Germany

Test specification:

Standard........................................:

IEC 61984:2008 (2nd Edition)

Test procedure..............................:

CB Scheme

Non-standard test

method…………..:

N/A

Test Report Form No..................... :

IEC61984B

Test Report Form(s) Originator ....:

VDE Testing and Certification Institute

Master TRF ....................................:

Dated 2010-05

This publication may be reproduced in whole or in part for non-commercial purposes as long as the IECEE is acknowledged as

copyright owner and source of the material. IECEE takes no responsibility for and will not assume liability for damages resulting from

the reader's interpretation of the reproduced material due to its placement and context.

If this Test Report Form is used by non-IECEE members, the IECEE/IEC logo and the reference to the CB

Scheme procedure shall be removed.

This report is not valid as a CB Test Report unless signed by an approved CB Testing Laboratory and

appended to a CB Test Certificate issued by an NCB in accordance with IECEE 02.

Test item description ....................:

Connectors

Trade Mark.....................................:

Manufacturer .................................:

Weidmüller Interface GmbH & Co. KG

Model/Type reference ...................:

OMNIMATE Signal - series BL/SL 5.08

BLZP 5.08HC series

SL 5.08HC series

Ratings ..........................................:

250 V~, 320 V~, 400 V~

Summary of content (28 pages)

PAGE 1
Test Report issued under the responsibility of: TEST REPORT IEC 61984 Connectors – Safety requirements and tests Report Number..............................: 2198607.50 Date of issue ................................. : 2017-02-21 Total number of pages.................. : 28 Applicant’s name ..........................: Weidmüller Interface GmbH & Co. KG Address ......................................... : Klingenbergstraße 16, D-32758 Detmold, Germany Test specification: Standard .....................
PAGE 2
Page 2 of 28 Report No.: 2198607.50 IEC 61984 Clause Requirement + Test Result - Remark Verdict Testing procedure and testing location: CB Testing Laboratory: DEKRA Certification B.V. Testing location/ address ........................: Meander 1051, 6825 MJ Arnhem The Netherlands Associated CB Laboratory: Testing location/ address ........................: Tested by (name + signature) ......: T. Cai Approved by (+ signature) ...........: M.
PAGE 3
Page 3 of 28 Report No.: 2198607.50 IEC 61984 Clause Requirement + Test Result - Remark List of Attachments (including a total number of pages in each attachment): Summary of testing: Tests performed (name of test and test clause): All applicable tests. Testing location: DEKRA Certification B.V.
PAGE 4
Page 4 of 28 Report No.: 2198607.50 IEC 61984 Clause Requirement + Test Result - Remark Copy of marking plate: (examples) BLZP 225° 5.08 HC 2.5mm² 250V 4KV/3 SL 5.
PAGE 5
Page 5 of 28 Report No.: 2198607.50 IEC 61984 Clause Requirement + Test Result - Remark Verdict Test item particulars.............................................. : connector Classification of installation and use .................... : Unenclosed fixed connector: male part Unenclosed free connector : female part Supply Connection ................................................ : 0,2 – 4,0 mm² ...............................................................................
PAGE 6
Page 6 of 28 Report No.: 2198607.50 IEC 61984 Clause Requirement + Test Result - Remark MECHANICAL TEST GROUP A (TABLE 10) Verdict P A1 VISUAL EXAMINATION: IEC 60512 Test 1a 6.2.2 Marking indelible and easily legible P Minimum marking on the connector a) trademark P Markings a) trademark and b) type identification on smallest unit of packaging P All other markings (c – k) given in the technical documentation or catalogue of the manufacturer P c) Rated current .............................
PAGE 7
Page 7 of 28 Report No.: 2198607.50 IEC 61984 Clause 6.19 Requirement + Test Result - Remark Verdict b) free connectors in which the terminations are protected against pull and twisting by mounting provisions in the end-use product P DIMENSIONAL EXAMINATION: IEC 60512 P Clearances and creepage distances according to IEC 60664. see table 0.2 P Connector dimensions comply with the DS or manufacturer’s specification. A2 DURABILITY OF MARKING 7.3.
PAGE 8
Page 8 of 28 Report No.: 2198607.50 IEC 61984 Clause Requirement + Test 6.5.4.1 The protective conductor terminal accepts a conductor with a minimum cross-section as specified in Table 1, Column 2: Minimum cross- section according to Table 1 ....: Result - Remark Verdict N/A mm²  6.5.4.2 With regard to design and type of construction, the protective conductor terminations are at least equivalent to the other terminations according to clause 6.: N/A A5 INTERLOCK N/A 7.3.
PAGE 9
Page 9 of 28 Report No.: 2198607.50 IEC 61984 Clause Requirement + Test Result - Remark P Test acc. to: IEC 60068-2-20 Solder terminations N/A Other terminations, not mentioned above, acc. to IEC standard .....................................................: A7 Verdict CONTACT RETENTION IN INSERT: IEC 60512 Test 15a P Test load shall be three times the specified insertion force (mating) of one contact or the specified insertion force of one contact plus 50 N, whichever is less.
PAGE 10
Page 10 of 28 Report No.: 2198607.50 IEC 61984 Clause Requirement + Test Result - Remark Dropping height ................................................: 750 mm Verdict — VISUAL EXAMINATION: IEC 60512 Test 1a 6.18.1 No damage likely to impair safety P 6.18.
PAGE 11
Page 11 of 28 Report No.: 2198607.50 IEC 61984 Clause Requirement + Test R2  1,5 R1 R2  5 m + R1...................: Result - Remark Verdict See appended table B4.1 P a) Impulse withstand voltage ............................: 4,8 kV  b) r.m.s. withstand voltage ................................: 2,21 kV  6.13 No breakdown or flashover occurred See appended table B4.2 P B5 BENDING (FLEXING) TEST (To be performed on new specimen) 7.3.
PAGE 12
Page 12 of 28 Report No.: 2198607.50 IEC 61984 Clause Requirement + Test Result - Remark THERMAL TEST GROUP C (TABLE 12) C1 7.3.7 6.16 P TEMPERATURE RISE TEST: IEC 60512 Test 5A Test conductor length according Table 7 ...........: 500 mm  Test conductor cross-section.............................: 2,5 mm²  Mated specimen ...............................................: mated  Test current ......................................................
PAGE 13
Page 13 of 28 Report No.: 2198607.50 IEC 61984 Clause Requirement + Test D3 DRY HEAT: IEC 60512 Test 11i Result - Remark Verdict P Mated specimen................................................: mated — Test duration ....................................................: 7 days — Upper temperature limit ....................................: 100 °C — VISUAL EXAMINATION: IEC 60512 Test 1a 6.6.3 Sufficient contact pressure through insulation P 6.8 / 6.
PAGE 14
Page 14 of 28 Report No.: 2198607.50 IEC 61984 Clause Requirement + Test Result - Remark DEGREE OF PROTECTION TEST GROUP E (TABLE 14) E1 P PROTECTION AGAINST ELECTRIC SHOCK Unenclosed connectors (for use inside an enclosure): 6.4.2.2 Verdict P 5.4 c1) COC classified as IP0X, no test required N/A 5.4 c2) COC Hand back safety (IP1X or IPXXA) N/A 50 mm sphere pressed with 20 N against mated specimen. No live parts accessible. 6.4.2.3 P 5.
PAGE 15
Page 15 of 28 Report No.: 2198607.50 IEC 61984 Clause Requirement + Test E3 DEGREE OF PROTECTION IP CODE: IEC 60529 7.3.6.3 Tests for IP Codes higher than IP2X or IPXXB 6.12 IP code according to IEC 60529 in mated condition or according manufacturers conditions ..............: IP — Maximum and minimum cross-section wiring or cable diameter connected..................................: mm² /  mm — 7.3.7.1 Result - Remark Verdict N/A mm² /  mm 7.3.7.
PAGE 16
Page 16 of 28 Report No.: 2198607.50 IEC 61984 Clause Requirement + Test Result - Remark A8.1 TABLE: Covers mounted / contacts not connected Nominal size (mm):  [mm] Tensible force [N] Verdict N/A  Displacement [mm] Min. ≤ N/A ≤ N/A ≤ N/A Max. Min. Max. Min. Max. A8.2 TABLE: Covers mounted Nominal size (mm):  [mm] N/A Torque [Nm]  Twist [ ° ] Min. ≤± N/A ≤± N/A ≤± N/A Max. Min. Max. Min. Max. B1 TABLE: Initial measurements (Contact resistance) Test current .........
PAGE 17
Page 17 of 28 Report No.: 2198607.50 IEC 61984 Clause B4.1 Requirement + Test Result - Remark Verdict TABLE: Final measurements (Contact resistance) P Test current....................................................... : 1A  Number of cycles .............................................. : 25  Condition ..........................................................
PAGE 18
Page 18 of 28 Report No.: 2198607.50 IEC 61984 Clause Requirement + Test Result - Remark C1 TABLE: Temperature rise test P Ambient temperature (°C)..................................: Thermocouple Locations Verdict  22,7 °C Test current Upper temperature (A) limit (ULT) (°C) Temperature measured (°C) — Terminals on female part 17,5 100 59,5 P Terminals on male part 24 100 87,4 P supplementary information: D1 TABLE: Initial measurements (Contact resistance) Test current ...........
PAGE 19
Page 19 of 28 Report No.: 2198607.50 IEC 61984 Clause D6 Requirement + Test Result - Remark Verdict TABLE: Dielectric strength (mated specimen) Test voltage applied between: a) Impulse withstand voltage applied Contact - Contact P b) r.m.s withstand voltage applied 4,8 Breakdown / flashover (Yes/No) 2,21 No Contact - Earth Contact - Surface supplementary information: 0.1 TABLE: Characteristic features Example ..................................
PAGE 20
Page 20 of 28 Report No.: 2198607.50 IEC 61984 Clause 0.
PAGE 21
Page 21 of 28 Report No.: 2198607.50 IEC 61984 Clause 0.
PAGE 22
Page 22 of 28 Report No.: 2198607.50 IEC 61984 Clause 0.1 Requirement + Test Result - Remark TABLE: Characteristic features Rated voltage(s)....................... : 250 V~, 320 V~, 400 V~ Rated current .......................... : BLZP 5.08HC series (female part) SL 5.08HC series (male part) min. no. of poles (Ta = 20°C) 17,5 A max. no. of poles (Ta = 20°C) 14 A min. no. of poles (Ta = 40°C) 14 A max. no. of poles (Ta = 40°C) 12 A min. no. of poles (Ta = 20°C) 24 A max. no.
PAGE 23
Page 23 of 28 Report No.: 2198607.50 IEC 61984 Clause 0.3.1 Requirement + Test Result - Remark Verdict TABLE: IEC 60112 / Tracking test Specimen Part Material Erosion depth [mm] Materialthickness [mm] Colour PTI Test solution [A] CTI PTI Test solution [B] Result Female part PBT 3,4 Orange 175 V - - P Male part 3,4 Orange 400 V - - P PA GF Supplementary information: 0.3.
PAGE 24
Page 24 of 28 Report No.: 2198607.50 IEC 61984 Clause Requirement + Test Drawing for BLZP 5.08HC series (female part) Drawing for SL 5.
PAGE 25
Page 25 of 28 Report No.: 2198607.50 IEC 61984 Clause Requirement + Test Result - Remark Temperature rise curve for BLZP 5.08HC series (female part) according to IEC 60512-5-2 Temperature rise curve for SL 5.
PAGE 26
Page 26 of 28 Report No.: 2198607.
PAGE 27
Page 27 of 28 Report No.: 2198607.
PAGE 28
Page 28 of 28 Report No.: 2198607.