User Documentation

4 5 6 V1.0 / 2020-10-29
8. Wiring the Redundant Power Inputs
The switch supports redundant power supply inputs which are located on the 4-pin
terminal block. Refer to illustration below for correct wiring.
Warning / Avertissement
 Take into consideration the following guidelines before wiring the
device
o Tenez compte des directrices suivantes avant de câbler l’appareil.
 Terminal block is mating with Plug and suitable for 12-24AWG.
Torque value 4.5 lb-in.
o Le bornier est compatible avec les connecteurs et convient pour 12-
24AWG. Valeur de couple 4,5 lb-in.
 The temperature rating of the input connection cable should higher
than 105°C.
o La température de service nominale du câble d’entrée doit être
supérieure à 105 °C.
 Use Copper Conductors Only.
o Utilisez uniquement des conducteurs en cuivre.
 Supplied by SELV or double insulation source evaluated by UL
61010-1 or 61010-2-201 power supply only.
o Fourni par la source SELV ou double isolation évaluée uniquement
par l'alimentation UL 61010-1 or 61010-2-201.
9. Communication Connections
Switch IE-SW-EL10-8GT-2GESFP is equipped with following communication
interfaces:
8x 10/100/1000Base-T(X) Ethernet ports
2x 100/1000Base-X slot to be used with SFP Transceivers (mini-GBIC)
[accessories]
Please only use cables suitable for the respective type of communication and ensure
that signals are protected from possible interference.
9.1 10/100/1000Base-T(X) RJ45 Ports
The 10/100BaseT(X) ports located on Ethernet Switch’s front panel are used to
connect to Ethernet-enabled devices. Below we show pinouts for both MDI (NIC-type)
ports and MDI-X (HUB/Switch-type) ports. Auto MDI-X ensures that both wiring-
schemes are supported (Automatic crossover function).
Pinouts 10/100/1000Base T(X) RJ45
8-Pin RJ45
Port
10/100 Base-T(X) MDI/MDI-X 1000Base-T MDI/MDI-X
Pin No. MDI port MDI-X port Pin No. MDI port MDI-X port
1 TD+(transmit) RD+(receive) 1 BI_DA+ BI_DB+
2 TD-(transmit) RD-(receive) 2 BI_DA- BI_DB-
3 RD+(receive) TD+(transmit) 3 BI_DB+ BI_DA+
4 Not used Not used 4 BI_DC+ BI_DD+
5 Not used Not used 5 BI_DC- BI_DD-
6 RD-(receive) TD-(transmit) 6 BI_DB- BI_DA-
7 Not used Not used 7 BI_DD+ BI_DC+
8 Not used Not used 8 BI_DD- BI_DC-
9.2 100/1000BaseSFP Port
The 100/1000BaseSFP type slots require either a 100BaseSFP or a 1000BaseSFP
fiber transceiver (mini-GBIC) to work properly.
Please only use SFP modules and cables that are compatible with each other to
establish an optical connection. Weidmüller provides transceiver models for various
distance requirements.
LC-Port with separate Transmit and Receive Port:
Remember to connect the Tx (transmit) port of device I to the Rx (receive) port of device
II, and the Rx (receive) port of device I to the Tx (transmit) port of device I
LC-Port Pinouts LC-Port to LC-Port Cable Wiring
10. LED Indicators
The front panel of the Ethernet Switch contains several LED indicators. The function of
each LED is described in the table below.
LED Color Status Description
PWR1 Green
On
Power is being supplied to power input
PWR1.
Off
Power is not being supplied to power
input PWR1.
PWR2 Green
On
Power is being supplied to power input
PWR2.
Off
Power is not being supplied to power
input PWR2.
LNK/ACT Green
On Port’s link is active.
Off Port’s link is inactive.
10/100/1000M
Green /
Amber
Green Port’s speed is 1000 Mbps.
Amber Port’s speed is 100 Mbps.
Off Port’s speed is 10 Mbps.
11. Specifications
Technology
Standards
IEEE 802.3 for 10Base-T
IEEE 802.3u for 100Base-TX and 100Base-FX
IEEE 802.3ab for 1000Base-T
IEEE 802.3z for 1000Base-X
IEEE 802.3x flow control
Processing Type Store and Forward
MAC Table size 4K
Packet buffer size 1.5 Mbit
Backplane bandwidth 20 Gbps
Jumbo frame support up to 9KB
Interfaces
RJ45 Ports
10/100/1000Base-T(X) auto negotiation speed, F/H
duplex mode and auto MDI/MDI-X connection
Fiber optic port 100/1000Base SFP slot
LED Indicators PWR1, PWR2 (Power), Port Link/Activity, Port Speed
Power
Input Voltage 24 V DC (12 - 48 V DC), 2 redundant inputs
Input Current
0.41 A @ 12 V DC
0.20 A @ 24 V DC
0.11 A @ 48 V DC
Connection
One removable 4-pin terminal block,
Wiring cable 12-24 AWG
Overload Current
Protection
Present
Reverse Polarity Protection Present
Physical Characteristics
Housing IP30 protection, metal
Dimension (W x H x D) 41 x 127 x 90 mm (1.61 x 5.0 x 3.54 in)
Weight 400 g
Installation DIN-rail
Environmental conditions
Operating Temperature -40 to 75°C (-40 to 167°F)
Storage Temperature -40 to 85°C (-40 to 185°F)
Ambient Relative Humidity 5 to 95% (non-condensing)
Altitude up to 2000 m
Regulatory Approvals
Safety UL 61010-1, UL 61010-2-201
EMC
EN 55032, EN 55024, FCC Part 15 Subpart B Class A,
IEC 61000-4-2 ESD: Contact: 6 kV; Air: 8 kV,
IEC 61000-4-3 RS: 80 MHz to 1 Ghz: 3 V/m,
IEC 61000-4-4 EFT: Power: 2 kV; Signal: 2 kV,
IEC 61000-4-5 Surge: Power: 1 kV; Signal: 1 kV,
IEC 61000-4-6 CS: 3 Vrms
Shock IEC 60068-2-27
Free Fall IEC 60068-2-31
Vibration IEC 60068-2-6
MTBF
Time 1.056.516 hrs
Database Telcordia SR332
Warranty
Time Period 5 years
Contact Information
Weidmüller Interface GmbH & Co. KG
Klingenbergstraße 26, 32758 Detmold / Germany
Phone [phone], Fax [phone]
E-Mail [e-mail], Internet www.weidmueller.com