User guide

ManualsBrandsWeidmuller ManualsHardwareDC/DC CCC LP - with voltage supply on the output side

WAVESERIES Signal Conditioners

DC/DC CCC LP

with Voltage Supply on the Output Side

Type Cat. No.

Screw-type connection

WAS4 CCC DC 4 ... 20 mA/4 ... 20 mA 8444980000

WAS4 CCC DC 4 ... 20 mA/0 ... 20 mA 8445010000

WAS4 CVC DC 4 ... 20 mA/0 ... 10 V 8445040000

Tension clamp connection

WAZ4 CCC DC 4 ... 20 mA/4 ... 20 mA 8444990000

WAZ4 CCC DC 4 ... 20 mA/0 ... 20 mA 8445020000

WAZ4 CVC DC 4 ... 20 mA/0 ... 10 V 8445050000

Read these instructions before using the product

and retain for future information.

Summary of content (8 pages)

PAGE 1
WAVESERIES Signal Conditioners DC/DC CCC LP with Voltage Supply on the Output Side Type Screw-type connection WAS4 CCC DC 4 ... 20 mA/4 ... 20 mA WAS4 CCC DC 4 ... 20 mA/0 ... 20 mA WAS4 CVC DC 4 ... 20 mA/0 ... 10 V Tension clamp connection WAZ4 CCC DC 4 ... 20 mA/4 ... 20 mA WAZ4 CCC DC 4 ... 20 mA/0 ... 20 mA WAZ4 CVC DC 4 ... 20 mA/0 ... 10 V Cat. No. 8444980000 8445010000 8445040000 8444990000 8445020000 8445050000 Read these instructions before using the product and retain for future information.
PAGE 2
1 General instructions The WAVESERIES signal conditioner DC/DC CCC LP with voltage supply on the output side should only be installed by qualified staff and be powered up following professional installation. 2 Application The WAVESERIES signal conditioner DC/DC CCC LP with voltage supply on the output side converts feedback-free input signals from the field into a standardised output signal. The output circuit is supplied with voltage and is galvanically isolated.
PAGE 3
.1 Mounting onto TS 35 DIN rails (s. Fig. 1) 3.2 Pluggable electronic components for range alteration (depending on model) (s. Fig. 2) 1. Remove connector, (depending on model either screw-type or tension clamp). 2. Press locking clips on both sides of the enclosure. 3. Pull out the circuit board. Warning!! The circuit board can only be inserted in one position. The connectors have been coded by the manufacturer, ensuring that they cannot be reversed. 3.3 Pluggable cross-connections for voltage supply (s.
PAGE 4
3.4 Labelling possibilities (s. Fig. 4) WS 10 connector markers can be used to label module. 4 Electrical connection (s. Fig. 5) Cat. No. 8444980000 (s. Fig. 6) Cat. No. 8445040000 5 Dimensions (s. Fig. 7) 6 Notes on CE labelling of WAVESERIES modules WAVESERIES modules, that carry CE-labelling, fulfil the requirements of the EU-Guidelines 89/336/EU "electromagnetic compatibility" and the therein listed harmonised European Norms (EN).
PAGE 5
The declarations of conformity are, in accordance with the abovementioned EU-Guideline, Article 10, held at the following address for the relevant authorities: Weidmüller Interface GmbH & Co. Postfach 3030 D-32720 Detmold 7 Technical data Input Input signal Input voltage, max. Input current, max. Output Output signal Load resistance Accuracy by Tu = 23 °C Temperature coefficient Step response time Cut-off frequency (-3 dB) 4 ... 20 mA 7V 25 mA 0 ... 20 mA or 4 ... 20 mA or 0 ... 10 V ≤ 500 Ω (0 ...
PAGE 6
Coordination of Insulation according to EN 50178, 04.98 Rated Voltage 300 V Rated surge Voltage 4 kV Overvoltage category III Contamination class 2 Clearance and creepage distances ≥ 3 mm Isolation voltage Voltage endurance Input/output/to mounting rail 4 kVeff/1 min Connection data Connection Insulating stripping length Solid core Flexible core With ferrules BLZ/SL 8 ± 0.5 mm 0.5 ... 2.5 mm2 0.5 ... 2.5 mm2 0.5 ... 1.
PAGE 7
EMC specification General Voltage supply Current consumption according to EN 55011, class B, group 1 according to EN 50081-1 according to EN 50082-2 Cross-connection, upper Cross-connection, lower Operating temperature Storage temperature 24 Vdc ± 20 % (19.2 ... 28.8 Vdc) < 32 mA at lout = 20 mA (0 ... 20 mA, 4 ... 20 mA) < 20 mA at lout = 10 mA (0 ... 10 V) 24 V, max. 2 A 0 V, max. 2 A 0 ... +55 °C -20 ...
PAGE 8
Accessories Cross-connection ZQV 2,5N/2 black Cross-connection ZQV 2,5N/2 red Cross-connection ZQV 2,5N/2 blue Cross-connection ZQV 2,5N/2 yellow 1718080000 1717900000 1717990000 1693800000 Terminal connector, 2-pole for screw-type connection BLZ 5,08/2 SN OR - orange 1526460000 - black 1526410000 Terminal connector, 2-pole for tension clamp connection BLZF 5,08/2 - orange 1707460000 - black 1707690000 Connector markers WS 10/5 Multicard for plotter labelling WS 10/5 blank 1635010000 1060860000 In the