Manual

ManualsBrandsWeidmuller ManualsHardwareDC/DC CCC LP - without additional voltage supply

WAVESERIES

Signal Conditioners DC/DC CCC LP

without additional Voltage Supply

Type Cat. No.

Screw-type connection

1-channel WAS5 CCC LP 8444950000

2-channel WAS5 CCC LP 8463580000

Tension clamp connection

1-channel WAZ5 CCC LP 8444960000

2-channel WAZ5 CCC LP 8463590000

Read these instructions before using the product

and retain for future information.

Summary of content (8 pages)

PAGE 1
WAVESERIES Signal Conditioners DC/DC CCC LP without additional Voltage Supply Type Screw-type connection 1-channel WAS5 CCC LP 2-channel WAS5 CCC LP Cat. No. 8444950000 8463580000 Tension clamp connection 1-channel WAZ5 CCC LP 2-channel WAZ5 CCC LP 8444960000 8463590000 Read these instructions before using the product and retain for future information.
PAGE 2
1 General instructions The WAVESERIES signal conditioner DC/DC CCC LP without additional voltage supply should only be installed by qualified staff and should only be powered up following professional installation. 2 Application The WAVESERIES signal conditioner DC/DC CCC LP without additional voltage supply are suitable for connection to 2-wire sensors. The signal is galvanically isolated and equally emitted as a 2wire signal. The voltage supply for input/output is generated from the input-circuit.
PAGE 3
.1 Mounting onto TS 35 DIN rails (s. Fig. 1) 3.2 Pluggable electronic components for range alteration (depending on model) (s. Fig. 2) 1. Remove connector, (depending on model either screw-type or tension clamp). 2. Press locking clips on both sides of the enclosure. 3. Pull out the circuit board. Warning!! The circuit board can only be inserted in one position. The connectors have been coded by the manufacturer, ensuring that they cannot be reversed. 3.3 Labelling possibilities (s. Fig.
PAGE 4
Electrical connection (s. Fig. 4) Example: 1-channel WAS5 CCC LP, Cat. No. 8444950000 (s. Fig. 5) Example: 2-channel WAS5 CCC LP, Cat. No. 8463580000 5 Dimensions (s. Fig. 6) 6 Notes on CE labelling of WAVESERIES modules WAVESERIES modules, that carry CE-labelling, fulfil the requirements of the EU-Guidelines 89/336/EU "electromagnetic compatibility" and the therein listed harmonised European Norms (EN).
PAGE 5
7 Technical data Input Input signal Input voltage, max. Input current, max. Operating current Voltage drop Output Output signal Load resistance Accuracy by Tu = 23 °C Influence of the load resistance Temperature coefficient Response time Remaining ripple Chopper frequency 0 ... 20 mA (4 ... 20 mA) 18 V 50 mA < 100 µA approx. 3 V at RL = 0 Ω at Iin = 20 mA approx. 13 V at RL = 500 Ω at Iin = 20 mA 0 ... 20 mA (4 ... 20 mA) ≤ 500 Ω < 0.1 % from end value < 0.
PAGE 6
Coordination of Insulation according to EN 50178, 04.98 (Safe Distance) Rated Voltage 300 V Rated surge Voltage 6 kV Overvoltage category III Contamination class 2 Clearance and creepage distances ≥ 5.5 mm Isolation voltage Voltage endurance Input/output Input/output/to mounting rail 4 kVeff/1 s 4 kVeff/1 min Connection data Connection Insulating stripping length Solid core Flexible core With ferrules BLZ/SL 8 ± 0.5 mm 0.5 ... 2.5 mm2 0.5 ... 2.5 mm2 0.5 ... 1.
PAGE 7
EMC specification according to EN 55011, class B, group 1 according to EN 50081-1 according to EN 50082-2 General Operating temperature mounted on DIN rails without clearance Storage temperature -25 ... +70 °C -40 ...
PAGE 8
Accessories Terminal connector, 3-pole for screw-type connection BLZ 5.08/3 SN OR - orange 1526560000 - black 1526510000 Terminal connector, 3-pole for tension clamp connection BLZF 5.08/3 - orange 1707470000 - black 1707700000 Connector markers WS 10/5 Multicard for plotter labelling WS 10/5 blank 1635010000 1060860000 In the interest of protecting the environment, return any spare operating instructions to your local stockist for re-use. Printed on chlorine-free bleached paper.