Media Converter – Value Line IE-MC-VL Series Hardware Installation Guide First Edition, December 2010 1243430000/00/12.10 Please note: This document and any further product information if available - can be downloaded at the internet link: http://www.weidmueller.com/downloads Copyright Notice Copyright © 2010 Weidmüller Interface GmbH & Co. KG All rights reserved. Reproduction without permission is prohibited.
Overview Weidmüller Media Converter, which is specially designed for reliable and stable operation in harsh industrial environments, provides industrial grade media conversion between 10/100BaseT(X) and 100BaseFX. The IE-MC-VL Series reliable industrial design is excellent for keeping your industrial automation applications running continuously, and comes with a relay output warning alarm to help prevent damages and losses.
Panel Layout of IE-MC-VL Series Top Panel View 1. Grounding screw 2. Terminal block for power input PWR1/PWR2 and relay output 3. Front Panel View IE-MC-VL-1TX-1ST Heat dissipation orifices 4. Dip switch 5. Power input PWR1 LED 6. Power input PWR2 LED 7. Fault LED 8. 100BaseFX (ST connector) Port 9. 10. FX port’s 100 Mbps LED FX port’s Full Duplex/Collision LED Front Panel View IE-MC-VL-1TX-1SC/1SCS 11. TP port’s 100 Mbps LED 12. 10/100BaseT(X) 13. TP port’s 10 Mbps LED 14.
Mounting Dimensions DIN-Rail Mounting The aluminum DIN-Rail attachment plate should be fixed to the back panel of Weidmüller Media Converter when you take it out of the box. If you need to reattach the DIN-Rail attachment plate to the device, make sure the stiff metal spring is situated towards the top, as shown in the figures below. STEP 1: STEP 2: Insert the top of the DIN-Rail into the The DIN-Rail attachment unit will slot just below the stiff metal spring. snap into place as shown below.
metal spring metal spring DIN-Rail DIN-Rail To remove the Media Converter from the DIN-Rail, simply reverse Steps 1 and 2 above. Wall Mounting (Optional) For some applications, you will find it convenient to mount the Media Converter on the wall, as illustrated below. STEP 1: Remove the aluminum DIN-Rail attachment plate from the device, and then attach the wall mount plates, as shown in the diagrams below. ⇒ STEP 2: Mounting the Media Converter on the wall requires 4 screws.
stability. II 3G ATEX Information 1. Certification number DEMKO 09 ATEX0812123x 2. 3. 4. 5. Ambient range (-40°C ≤ Tamb ≤ 75°C) Certification string (Ex nC nL IIC T4) Standards covered ( EN60079-0:2006, EN60079-15:2005) The conditions of safe usage: y The Ethernet Communication Devices are to be mounted in an IP54 enclosure and used in an area of not more than pollution degree 2 as defined by IEC60664-1. A 4mm2 conductor must be used when a connection to the external grounding screw is used.
WARNING ATTENTION ATTENTION ATTENTION This equipment has been evaluated as EEx nC IIC T4 equipment under DEMKO Certificate No. 03 ATEX 0324537U. Each module is marked with II 3G and is suitable for use in Zone 2 Explosive Atmospheres. Devices must be installed in a minimum IP 54 enclosure as defined in IEC 60529 and EN 60529. This unit is a built-in type. During installation into certain end equipment, it must comply with fire enclosure stipulations of IEC 60950/EN60950, or similar statements.
ATTENTION This product is intended to be mounted to a well-grounded mounting surface such as a metal panel. Wiring the Alarm Contact The Alarm Contact is made up of the two middle contacts of the terminal block on the Media Converter’s top panel. Refer to the next section for detailed instructions on how to connect the wires to the terminal block connector, and how to attach the terminal block connector to the terminal block receptor.
ATTENTION Before connecting the device to the DC power inputs, make sure the DC power source voltage is stable. Communication Connections IE-MC-VL models have one 10/100BaseT(X) Ethernet port, and one 100BaseFX (SC or ST type connector) fiber port. 10/100BaseT(X) Ethernet Port Connection The 10/100BaseT(X) ports located on the Media Converter’s front panel are used to connect to Ethernet-enabled devices.
other optical line is used transmit data from device II to device I, for full-duplex transmission. All you need to remember is to connect the Tx (transmit) port of device I to the Rx (receive) port of device II, and the Rx (receive) port of device I to the Tx (transmit) port of device II. SC-Port Pinouts ST-Port Pinouts Tx Tx Rx Rx ATTENTION This is a Class 1 Laser/LED product. Do not stare into the Laser Beam.
Dip Switch Setting IE-MC-VL Series DIP switch Dip Switch 1 (Default: Off ) ON: Enables the PORT Alarm. If the port’s link fails, the relay will form an open circuit and the fault LED will light up. ON DIP Off: Disables the corresponding PORT Alarm. The relay will form a closed circuit and the Fault LED will never light up.
On 100M (FX) FDX/ COL GREEN GREEN FX port’s 100 Mbps is active Blinking Data is being transmitted at 100 Mbps Off 100BaseFX port is inactive On 100BaseFX port is being transmitted at full duplex Blinking Off Collision occurs 100BaseFX port is being transmitted at half duplex Auto MDI/MDI-X Connection The Auto MDI/MDI-X function allows users to connect the Media Converter’s 10/100BaseTX ports to any kind of Ethernet device, without paying attention to the type of Ethernet cable being used for th
Specifications Technology Standards Interface RJ45 ports Fiber ports LED Indicators Dip Switch Alarm Contact IEEE802.3, 802.3u, Link Fault Pass-Through 10/100BaseT(X) 100BaseFX (SC, ST connectors available) Power, Fault, 10/100M, Full Duplex/Collision Port break alarm mask, 100BaseFx Full/Half duplex selection One relay output with current carrying capacity of 1A @ 24 VDC Optical Fiber Distance, km Multi mode 5 Single mode, 40 40 Wavelength, nm 1310 1310 Min. TX Output, dBm -20 -5 Max.
Shock Free Fall Vibration EN61000-4-3 (RS), level 3 EN61000-4-4 (EFT), level 3 EN61000-4-5 (Surge), level 2 EN61000-4-2 (CS), level 3 IEC 60068-2-27 IEC 60068-2-32 IEC 60068-2-6 WARRANTY 5 years Weidmüller gives a 5 year warranty on this product in accordance with the warranty terms as described in the general conditions of sale of the Weidmüller company which has sold the products to you.
