Table of contents INTRODUCTION . . . . . . . . . . . . . . . . . . . . . SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . ABOUT THIS DEVICE . . . . . . . . . . . . . . . . . FIRST OPERATION . . . . . . . . . . . . . . . . . . . THE DISPLAY . . . . . . . . . . . . . . . . . . . . . . . ATTACHING THE WRIST SLEEVE . . . . . . . . . CORRECT MEASUREMENT . . . . . . . . . . . . . . CARRYING OUT MEASUREMENTS . . . . . . . . SAVING VALUES . . . . . . . . . . . . . . . . . . . . CLEANING AND MAINTENANCE . . . . .
INTRODUCTION Thank you for the trust you have placed in us! We congratulate you on the purchase of your new blood pressure device and are convinced that you will be delighted with this modern piece of equipment.
SAFETY INSTRUCTIONS • The device is suitable for healthy adults. Use the unit for comparative measurements, particularly during sporting activities. Do NOT use the unit for medical diagnosis. It can not replace medical intervention. • The unit is battery-operated. Batteries may endanger life if swallowed. For these reasons, keep the unit out of reach of children. If a battery is swallowed, please obtain immediate medical assistance.
ABOUT THIS DEVICE The device is used to measure blood pressure at the wrist. It is suitable for healthy people above 12 years of age and can be use to make comparative measurements – especially during sporting activities. If the values obtained give you cause to be concerned about your health, take medical advice.
FIRST OPERATION 1. Remove the cover of the battery compartment in the direction of the arrow. 2) Insert two 1.5V batteries, AAA, LR03 (alkaline). Pay attention to the polarity (the negative terminal faces the spring). 3) Close the battery compartment. Replace the batteries – if the battery icon appears on the display, – if the display remains blank after pressing the ON/OFF button. Setting the date and time Make the settings within 10 seconds; then the display moves to the next setting. 1.
THE DISPLAY Memory area icon 1 or 2; select the memory area with the button. . The battery icon appears if the batteries need to be changed. The pulse sign appears when the pulse is displayed. EE (E1, E2) Error notifications for operating and device errors.
ATTACHING THE WRIST SLEEVE 1. Attach the wrist sleeve in such a way that it is approx. 5 - 10mm away from the palm of your left hand (see fig. B). Ensure that no articles of clothing are trapped in the sleeve. 2) Hold the lower part of the sleeve as shown in fig. C. Pull down and wrap it around and upwards, so that there is no gap between the sleeve and your wrist. 3) Use your thumb to hold the sleeve cover while you wrap it upwards. 4) Wrap the sleeve according to the shape of your wrist.
CORRECT MEASUREMENT • Place your elbow on the table or other supporting surface, and hold your arm so that the wrist sleeve is at heart height. In doing so, support your lower arm on the storage box or on a folded towel or similar. • To measure your blood pressure, sit comfortably on a chair, take 5 or 6 deep breaths and relax.
CARRYING OUT MEASUREMENTS 1. Attach the wrist sleeve to your wrist as described above. 2) Press the ON/OFF button. All indicators are displayed for a few seconds on the screen; then the screen shows the time and the most recently selected memory space. Measurement starts automatically; the device pumps up the sleeve. If the sleeve pressure is too low the device pauses and pumps up the sleeve again until it reaches a sleeve pressure that is appropriate for the measurement.
SAVING VALUES The device has two memory areas and . Up to 50 measurements can be saved in each area. You can also display the average values of the saved measurements. 1. Before measuring select the memory area with the memory area button. 2) Take the measurement. When the values are displayed MEM flashes on the screen for a few seconds. The measured value is saved into the chosen memory space. 3) Press the MEMORY button repeatedly to display the saved values.
CLEANING AND MAINTENANCE Notes on maintenance It is recommended that you check the usability of the unit every three years or after repairs. According to the "Operating Regulations for Medical Products" a technical measurement check must take place every 2 years if the device is used for commercial purposes. Cleaning/storage Do not clean the device with solvents that contain alcohol. Only use a soft cloth, which may be moistened, and a mild cleaning agent. Then dry the device carefully.
ENVIRONMENTAL PROTECTION/ DISPOSAL The unit is battery-operated. Do not dispose of dead batteries in the household rubbish. After the end of its life, ensure to dispose the product beneficial to the environment. Do not dispose the product in the household rubbish.
ERROR MESSAGES Defect Possible cause and solution EE / E1 / E2 The sleeve is not attached correctly. Please refer to the notes in these instructions. Movement during measurement. Do not move or speak during measurement The device is not able to measure the values appropriately. Take the measurement again after a 5 minute break. Contact the service centre if the error is indicated repeatedly over a long period of time. The batteries are dead. Replace both batteries with 2 new 1.
Guidelines and manufacturer's declaration regarding EMC Guidelines and manufacturer's declaration – electromagnetic emissions Model MD 10544 is designed for operation in an environment as described below: The customer or user of Model MD 10544 should ensure that it is operated in such an environment. Interference emission measurements In line with Electromagnetic environment guidelines RF emissions according to CISPR 11 Group 1 Model MD 10544 uses RF energy for its internal operation.
Magnetic field at the power frequency (50/60 Hz) according to IEC 61000-4-8 NOTE 3 A/m Not applicable The MD 10544 contains no devices susceptible to magnetic fields. . UT is the mains AC voltage prior application of the test level. Guidelines and manufacturer's declaration – electromagnetic stability Model MD 10544 is designed for operation in an electromagnetic environment as described below: The customer or user of Model MD 10544 should ensure that it is operated in such an environment.
Recommended protective distances between portable and mobile RF telecommunication devices and the MD 10544 Model MD 10544 is intended for operation in an electromagnetic environment in which the RF interference is controlled .