Programming Menu
SCANTEAM 2380 Programming Menu NOTES Please Note: The programming features on each menu page are not supported in all models and software revisions of the SCANTEAM 2380. Notations are included if the feature is available only in certain models. Contact your Welch Allyn Sales Coordinator for the revision/model to fit your needs. The SAMPLE BAR CODES page (near the end of the programming menu) contains bar code symbols that you may use to verify that you have programmed your SCANTEAM 2380 correctly.
STATUS SCANTEAM 2380/PM Programming Menu CHECK SHOW FIRMWARE REVISION LEVEL Scan the bar code below to display the revision level of the SCANTEAM 2380 firmware. For example: After scanning the Firmware Revision Level bar code, “(C) WA93C” is output to the terminal/host device. The “C” at the end indicates the firmware is at revision level C. Firmware Revision Level SHOW SOFTWARE NUMBER Scan the bar code below to display the SCANTEAM 2380 software number.
USER’S NOTES 4 SCANTEAM 2380 Programming Menu
SYSTEM SCANTEAM 2380/PM Programming Menu GUIDE USE THIS PAGE As a general overview of the programming menu. The programming menu consists of two basic components as shown below. SELECTION II (RETAIL) USE THIS PAGE BAR CODE CHART Programming Menu CODE Programming Menu USE THIS PAGE In combination with the adjoining menu pages to program the unit. The bar codes on this page correspond to symbols in shaded areas on adjoining menu pages.
TERMINAL SCANTEAM 2380 Information and Examples SELECTION DIRECT CONNECT ENABLE When enabled, this programming selection allows the wand scanner to replace the keyboard. The scanner will respond the the PC keyboard initialization commands upon power up. This selection is for an AT keyboard only with a terminal ID of 03. LOW POWER When enabled, this programming selection puts the wand scanner in a low power mode.
TERMINAL SCANTEAM 2380 Programming Menu SELECTION USE THIS PAGE To select the terminal type. To enable the AT Direct Connect feature. To enable the Low Power feature.
OUTPUT PARAMETERS SCANTEAM 2380 Information and Examples & FORMAT SELECTIONS PREAMBLE/POSTAMBLE Preambles and Postambles are characters added by the 2380 to scanned bar code data. These characters are sent with the bar code data to the terminal. Use the Hex–ASCII table below to find the alpha–numeric code to be used for programming a particular Preamble or Postamble. NOTE: The 2380 will translate characters 00–1F (keyboard function codes) into keyboard “function keys.
OUTPUT PARAMETERS & FORMAT SELECTION SCANTEAM 2380 Programming Menu scan USE THIS PAGE To select the pre–programmed asterisked (*) values by scanning DEFAULT symbol. To add preambles and/or postambles to the bar code. To select function transmit enable. To select keyboard type. To set intercharacter, interfunction, and intermessage delays to specific values. To control scanning indicators or enable function records feature. To enable the Append Buffer when Code 3 of 9 with append option is enabled.
COMM 1 SCANTEAM 2380 Information and Examples INTERNATIONAL KEYBOARDS The unit aligns the keyboard layout based on the International Keyboard selected here. INTERMEC COMPATIBILITY YES – Allows the unit to be compatible with Intermec keyboard function codes. NO – The default keyboard function codes that are in the preamble and postamble remain active at all times.
COMM 1 SCANTEAM 2380 Programming Menu USE THIS PAGE To select foreign keyboards. To enable Intermec compatibility scan selections ENTER INTERNATIONAL KEYBOARDS (3) scan scan DEFAULT INTERMEC COMPATIBILITY (3) variables scan scan France A Germany B Spain C Switzerland D Italy E USA F* Sweden (4) G Canada (5) H Portugal (5) I Yes/No* scan EXIT Notes: (1) * Designates DEFAULT selections. (2) See facing page for more information and examples.
SCANCODE SCANTEAM 2380 Information and Examples SELECTION K2 SCANCODE CAPABILITY Reconfigures the 2380 to use K2 (SCANTEAM 2300) compatible scancodes. If other Welch Allyn wedge products are being used or are planned for future use, it is strongly recommended to program this selection for “YES” and use the function codes found in the Keyboard Function Codes Table 2 and Table 3 in the Appendix A.8 of the 2380Technical Manual.
SCANCODE SCANTEAM 2380 Programming Menu SELECTION USE THIS PAGE (3) To select the pre–programmed asterisked (*) values by scanning DEFAULT symbol. To reconfigure the 2380 to use the 2380 Function Codes. (Applies only to IBM XT, AT, and PS/2’s.) Refer to Appendix A.8 in 2380 Technical Manual for two options. To reconfigure the 2380 to use a new Scancode Table. Only applicable to customers who request new Scancode Table (that is, foreign keyboards).
SYMBOLOGY SELECTION SCANTEAM 2380 Information and Examples INDUSTRIAL INDUSTRIAL CODE OUTPUT FORMATS aSX . . . bSXX . . eXX . . . fXX . . . . gXX . . . hXX . . . iXX . . . . jXX . . . .
SYMBOLOGY SCANTEAM 2380 Programming Menu SELECTION (CODES) USE THIS PAGE To select the pre–programmed asterisked (*) values by scanning DEFAULT symbol. To specify desired bar code symbologies. To select symbology options.
SYMBOLOGY SELECTION SCANTEAM 2380 Information and Examples RETAIL RETAIL CODE OUTPUT FORMATS Non–Zero Suppressed UPC–A and UPC–E Output Format cNXXXXXXXXXXC UPC–A cNXXXXXXXXXXC–SS UPC–A with 2 digit supplemental cNXXXXXXXXXXC–SSSSS UPC–A with 5 digit supplemental cNXXXXXXXXXXC UPC–E cNXXXXXXXXXXC–SS UPC–E with 2 digit supplemental cNXXXXXXXXXXC–SSSSS UPC–E with 5 digit supplemental Zero Suppressed UPC–A and UPC–E Output Format cNXXXXXXXXXXC UPC–A cNXXXXXXXXXXC–SS UPC–A with 2 digit supplemental cNXXXXXXX
SYMBOLOGY SCANTEAM 2380 Programming Menu SELECTION (CODES) USE THIS PAGE To select the pre–programmed asterisked (*) values by scanning DEFAULT symbol. To specify desired bar code symbologies. To select symbology options.
USER’S NOTES 18 SCANTEAM 2380 Programming Menu
KEYBOARD LAYOUTS Continued SCANTEAM 2380 Programming Menu A1 A2 A3 A4 C4 C5 B7 B8 B9 C6 A0 A5 A6 C3 B4 B5 B6 B1 B2 B3 C2 A7 A8 C0 A9 B0 C1 IBM XT Keyboard D1 A2 A3 A4 A5 A6 A7 A8 A9 B0 D7 D8 C9 C3 A0 D6 B7 B8 B9 B5 B4 B5 B6 A0 B1 B2 B3 C0 C1 IBM PC/AT Keyboard C5 A1 A2 A3 A4 A5 A6 A7 A8 A9 B0 C7 C8 C9 C3 A0 B7 B8 B9 C6 A0 B5 B4 B5 B6 B1 B2 B3 C0 C1 IBM PS2–30 Keyboard 19
USER’S NOTES 20 SCANTEAM 2380 Programming Menu
SAMPLE BAR CODES SCANTEAM 2380 Programming Menu This page contains bar code symbols in some of the most commonly used symbologies. You may use these codes to test that your system is properly programmed for a particular symbology. UPC–A 0–3132312078–6 UPC–A 0–3132312078–6 5 add on 56098 EAN–13 97–8033029095–1 Code 128 CODE 128 Interleaved 2 of 5 1234567890 Codabar B–:/.
USER’S NOTES 22 SCANTEAM 2380 Programming Menu
SCANTEAM 2380 Programming Menu USER’S NOTES
BAR CODE CHART SCANTEAM 2380 Programming Menu USE THIS PAGE In combination with the adjoining menu pages to program the 2380. The bar codes on this page correspond to symbols in shaded areas on adjoining menu pages. SCAN these bar codes in the sequence indicated on menu page to program desired selections and variables.
SCANTEAM 2380 Programming Menu USE THIS PAGE CODE 3 OF 9 SYMBOLS FUNCTION RECORD CODES For transmitting functions using function record codes.
2380/PM Rev K