User's Manual Addendum
Table Of Contents
- UPDATE
- Contents
- NEW ROOM
- 1. If the Propaq CS monitor has already been connected to the patient, save the patient’s Trends ...
- 2. If the monitor is not already connected to the patient, attach leads and sensors to the patien...
- 3. Plug in the Acuity network cable to the Acuity network jack on the monitor side panel as shown...
- 4. Connect the ac power adapter to the monitor and the wall outlet to charge the battery. Check t...
- 5. When the monitor completes the connection to Acuity, it displays the message ON NETWORK (or al...
- 6. If alarm limits have not been set, do so at the monitor or at the Acuity Central Station using...
- 1. To permanently disconnect the Propaq CS monitor from the Acuity network, press the NETOFF key...
- 2. Within 15 seconds, disconnect the Acuity network cable from the Propaq CS monitor side panel a...
- 1. Press the NETOFF key on the upper left corner of the monitor display to disconnect from Acuit...
- 2. Within 15 seconds unplug the Acuity network cable from the Wireless Propaq CS Acuity connector...
- 3. After the network connection is established, select the Acuity Unit, patient, and room from th...
- 1. Make sure the Acuity network cable is not plugged into the Acuity connector and an Acuity beds...
- 2. Confirm that the Wireless Propaq CS displays the flashing message SEARCHING in the upper left ...
- 3. Confirm that within one minute the monitor displays these alternating messages:
- 4. After the network connection is established, the monitor may prompt you to select an Acuity Un...
- 5. The Wireless Propaq CS displays a list of possible patients. If your patient has been pre-admi...
- 6. Within a few seconds the Wireless Propaq CS displays a list of unassigned rooms.
- 7. Customize alarm limits for your patient if needed. Refer to the Propaq CS Directions For Use.
- 1. A DROPOUT equipment alert occurs at the Acuity Central Station. Acknowledge the alert at Acuity.
- 2. An equipment alert occurs at the Wireless Propaq CS with this message:
- 1. Press the NETOFF key on the upper left corner of the monitor display. (From the Main Menu you...
- 2. Disconnect the leads and sensors from the patient and turn off the power to the monitor.
- 1. Turn on power to the Wireless Propaq CS and confirm that the monitor displays the powerup screen.
- 2. The Wireless Propaq CS will then present a series of menus and messages requesting you to prov...
- 1. From the Main Menu, press SETUP, ACUITY, CHANGE PATIENT, NEW ROOM.
- 1. From the Main Menu, press SETUP, ACUITY, CHANGE PATIENT, TRANSFER. Within a few seconds the Wi...
- 2. Scroll up or down to highlight the new unit, then press Select.
- 3. After the patient is assigned to the new unit, the Wireless Propaq CS displays a list of unass...
- 1. From the Main Menu, press SETUP, ACUITY, CHANGE PATIENT, NEWPATIENT.
- 1. Plug the Acuity network cable into the Wireless Propaq CS Acuity connector and an Acuity bedsi...
- NEW ROOM
10 Welch Allyn
Note
When a Propaq CS monitor in Adult or Pediatric Mode is connected to an Acuity System, the
audible alarms at the bedside Propaq CS monitor can be delayed up to 4 minutes and 15
seconds. The delay time is selected in Acuity software at the time of Acuity installation. Visual
alarm indications are not delayed.
Disconnect the Hardwired Monitor from the Acuity System
1.
To permanently disconnect the Propaq CS monitor from the Acuity
network, press the
NET OFF
key on the upper left corner of the monitor
display. (From the Main Menu you can also press
SETUP,
ACUITY
,
NET
OFF
.)
2.
Within 15 seconds, disconnect the Acuity network cable from the
Propaq CS monitor side panel and the bedside jack. If the patient will
no longer be monitored with this monitor, turn off the monitor to erase
trend information.
If you want to temporarily disconnect the Propaq CS monitor from the
Acuity network and reconnect the same patient to the Acuity network later,
see the
Acuity System Reference Guide
.
Note
If the Propaq CS has the wireless option, be aware that after you disconnect the hardwire
connection and disconnect the Acuity network cable, the Wireless Propaq CS will attempt to
establish a wireless connection to Acuity as long as the power is on.
Switch from Hardwired to Wireless Monitoring
ADULT
MON
17:05:10
PRINT FAULT
II
P
(
P2
NET
OFF
ON NETWORK
mV
cm
1
H
B
P
ALLEN KIM
Press to disconnect
from Acuity