011C WELLS BLOOMFIELD, LLC 10 Sunnen Drive P.O.Box 430195 St. Louis, MO 63143 USA telephone: 314-781-2777 fax: 314-781-2714 www.wellsbloomfield.
LIMITED WARRANTY STATEMENT Unless otherwise specified, all commercial cooking equipment manufactured by WELLS BLOOMFIELD, LLC is warranted against defects in materials and workmanship for a period of one year from the date of original installation or 18 months from the date of shipment from our factory, whichever comes first, and is for the benefit of the original purchaser only.
TABLE OF CONTENTS WARRANTY FEATURES & OPERATING CONTROLS PRECAUTIONS & GENERAL INFORMATION AGENCY LISTING INFORMATION INSTALLATION OPERATION MAINTENANCE INSTRUCTIONS CLEANING INSTRUCTIONS TROUBLESHOOTING SUGGESTIONS EXPLODED VIEW & PARTS LIST WIRING DIAGRAM PARTS & SERVICE CUSTOMER SERVICE DATA xi 2 3 3 4 6 7 8 10 12-14 15 16 17 INTRODUCTION Thank You for purchasing this Wells Bloomfield appliance.
FEATURES & OPERATING CONTROLS A. THERMOSTAT 1. On THERMOSTATICALLY CONTROLLED warmers, power is applied to the heating element according to the control knob position and the actual temperature at the temperature sensing thermobulb. 2. The desired temperature is controlled by rotating the TEMPERATURE CONTROL KNOB. The knob has a numeric scale, where higher numbers correspond to higher temperature. 3. On warmers equipped with an INDICATOR LIGHT, the light will glow when the thermostat is calling for heat (i.
PRECAUTIONS AND GENERAL INFORMATION This appliance is intended for use in commercial establishments only. This appliance is intended to hold pre-heated food for human consumption. No other use is recommended or authorized by the manufacturer or its agents. Operators of this appliance must be familiar with the appliance use, limitations and associated restrictions. Operating instructions must be read and understood by all persons using or installing this appliance.
INSTALLATION NOTE: DO NOT discard the carton or other packing materials until you have inspected the appliance for hidden damage and tested it for proper operation. Refer to SHIPPING DAMAGE CLAIM PROCEDURE on the inside front cover of this manual. WARNING: RISK OF INJURY Installation procedures must be performed by a qualified technician with full knowledge of all applicable electrical and plumbing codes. Failure can result in personal injury and property damage.
INSTALLATION 3. For “top-mounted” warmers (i.e. warmers mounted from above the counter top): a. Verify that provided sealants are applied to the underside of the warmer top flange prior to setting the unit into the cutout. b. After installation, verify that the tabs on the Wellsloks are turned out to lock the warmer into the counter c. Apply a thin bead of food-grade silicone sealant around the flange to seal it to the counter. d.
OPERATION CAUTION: HOT SURFACE Exposed surfaces can be hot to the touch and may cause burns. CAUTION: SHOCK HAZARD DO NOT splash or pour water onto control panel or wiring. Always use an inset. DO NOT place food directly into the warmer. Always pour hot water into the warmer before it is preheated. DO NOT pour water into a dry, heated warmer. This may damage the unit. WET OR DRY OPERATION for WARMERS 1. Carefully read the description of the warmer operation on the specification sheet. 2. a.
MAINTENANCE INSTRUCTIONS CARE OF STAINLESS STEEL Stainless steel is a marvelous material: strong, lustrous and low maintenance. With a minimum of care, it will normally retain its beauty and durability for the life of the equipment. In some applications, however, special care is required in order to maintain stainless steel’s special properties. External components, such as cabinets and control panels, are finished with a grain pattern.
CLEANING INSTRUCTIONS CAUTION: SHOCK HAZARD Do NOT splash or pour water into or over any control panel or wiring. CAUTION: SHOCK HAZARD DAILY CLEANING INSTRUCTIONS PREPARATIONS: Turn control knob(s) to OFF. Allow warmer to cool before proceeding. Remove any insets, pans and/or adapter tops. Drain or remove water from well if used for wet operation. FREQUENCY: Minimum - daily.
CLEANING INSTRUCTIONS WEEKLY CLEANING INSTRUCTIONS CAUTION: PREPARATIONS: Remove any insets, pans and/or adapter tops. Drain or remove water from well if used for wet operation. FREQUENCY: Weekly, or whenever lime or scale is seen accumulating on the sides of the warmer pans. TOOLS: Commercial Delime Cleaner Plastic Scouring Pad Clean Cloth or Sponge 1. Add water to pans until water is at normal operating level (1” - 1 1/2” deep) or covers accumulated scale. 2.
TROUBLESHOOTING SUGGESTIONS SYMPTOM POSSIBLE CAUSE SUGGESTED REMEDY No power to warmer Circuit breaker off or tripped Reset circuit breaker Warmer will not heat Temperature control not set Set control to desired temperature Wet insulation Verify flange-to counter seal is sound, or reseal with food-grade silicone sealant Pan leaking or other internal damage Contact your Authorized Wells Service Agency for repairs Internal damage Contact your Authorized Wells Service Agency for repairs Mineral
MAINTENANCE INSTRUCTIONS CARE OF STAINLESS STEEL Stainless steel is a marvelous material: strong, lustrous and low maintenance. With a minimum of care, it will normally retain its beauty and durability for the life of the equipment. In some applications, however, special care is required in order to maintain stainless steel’s special properties. External components, such as cabinets and control panels, are finished with a grain pattern.
EXPLODED VIEW MOD-100T, MOD-100TD, MOD100HT, MOD100HTD 21 2 1 11 3 THERMOBULB 10 5 6 11 7 8 12 13 14 15 16 17 18 20 13 19 12 IL1905, Rev A MODEL: MOD100T, MOD100HT 12 M011C.
PARTS LIST MOD-100T, MOD-100TD, MOD100HT, MOD100HTD Fig No Part No Qty 2N-300166UL ELEM 208V 1650W MODS 2N-303375UL 1 2 ELEM HEATING 240V 1650W 1 MOD100T, MOD100T-230, MOD100T6, PAN ELEM ASSY MOD100T 208 MOD100TD, MOD100TD-230, MOD100TD6 , MOD100TDAF 1 P2-40628 2 7 8 P2-45066 P2-45067 1 1 P2-40629 P2-45186 10 5P-21709 P2-30401 PAN ELEM ASSY MOD100HTD PAN ELEM ASSY MOD100HT PAN ELEM ASSY MOD100HTD 1 BRKT THERMO BULB 4.25 INSUL FG .6 MICRO 1X 45 1.75 INSUL FG .
EXPLODED VIEW & PARTS LIST MOD-127TD 21709 MOD-127TD ONLY 504102 MOD-127TD ONLY 50397 (pk 6) 500706 500702 make from 56196 (150' roll) 503352 THERMOBULB (ref.) 8706-109 50177 60846 58968 60843 55687 51023 51040 50177 60498 0 8706-109 OFF H 7 3 WELLS 6 5 4 14 8 2 LO I M011C.
M011C.
PARTS & SERVICE Always use an inset. DO NOT place food directly into the warmer pan. DESCRIPTION PART NO. ADAPTERS & INSETS ADAPTER TOP, convert 12” x 20” warmer to hold two 7 qt. insets 21502 ADAPTER TOP, convert 12” x 20” warmer to hold two 4 qt. and two 2½ qt 21503 ADAPTER TOP, convert 12” x 20” warmer to hold three 4 qt. insets 21616 ADAPTER TOP, convert 12” x 20” warmer to hold one 7qt. and one 4 qt. 21618 ADAPTER TOP, convert 12” x 20” warmer to hold four 2½ qt.
PARTS & SERVICE DESCRIPTION PART NO. ACCESSORIES 6 oz. SOUP LADLE 21764 WELLSLOK EXTENSION KIT, for UL LISTED circular warmers only, adapt to wood counter up to 1¾” thick 22592* WELLSLOK EXTENSION KIT, for UL LISTED 12” x 20” warmers only, adapt to wood counter up to 1¾” thick 22593* M011C.
Commercial Food Equipment Service Association Wells Bloomfield proudly supports CFESA Commercial Food Equipment Service Association SERVICE TRAINING - QUALITY SERVICE Genuine Parts Protect - YOU - All - Ways CUSTOMER SATISFACTION WELLS BLOOMFIELD, LLC 10 Sunnen Drive P.O.Box 430195 St. Louis, MO 63143 USA telephone: 314-781-2777 fax: 314-781-2714 www.wellsbloomfield.
