Owner`s manual

ManualsBrandsWells ManualsFood WarmerMOD-400

JARVIS

PRODUCTS CORPORATION

33 ANDERSON ROAD, MIDDLETOWN, CONNECTICUT 06457--4926

UNITED STATES OF AMERICA E--MAIL. j

arvis.products.corp@snet.net

FAX 860--347--6978 TEL. 860--347--7271 WWW. jarvisproducts.com

6205005:::.

Table Of Contents: Page.........................................

•Notice to Employer and Safety Director 2..........................

•Notice to Operators, Maintenance and Cleanup Personnel 3.........

•Parts Diagram 4................................................

•Parts List 5....................................................

•Installation Instructions 6........................................

•General Safety Instructions 7.....................................

•Operation Instructions 8.........................................

•Maintenance Instructions 10......................................

NOT FOR HOME USE

PORTABLE POWER SAW

MODEL 400

Owner’s Manual For:

Summary of content (12 pages)

PAGE 1
NOT FOR HOME USE Owner’s Manual For: PORTABLE POWER SAW MODEL 400 Table Of Contents: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page •Notice to Employer and Safety Director . . . . . . . . . . . . . . . . . . . . . . . . . . 2 •Notice to Operators, Maintenance and Cleanup Personnel . . . . . . . . . 3 •Parts Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 •Parts List . . . . . . . . . . . . . . . . . . . . .
PAGE 2
notice to employer and safety director MODEL 400 pg 2 of 12 Keep hands clear. NOTICE TO EMPLOYER AND SAFETY DIRECTOR AVOID INJURY 1. Remove and repair any tool that malfunctions. All personnel must be instructed to remove any malfunctioning equipment. 2. Ensure that all employees who use this tool are trained in the proper use of this tool and are aware of the dangers that may arise if they do not follow the procedures outlined in this brochure. 3.
PAGE 3
notice to operators, maintenance and cleanup personnel MODEL 400 pg 3 of 12 Keep hands clear. NOTICE TO OPERATORS, MAINTENANCE AND CLEANUP PERSONNEL REMOVE ANY MALFUNCTIONING TOOL FROM SERVICE REPORT ANY PROBLEMS TO YOUR SUPERVISOR 1. Always wear eye protection in accordance with OSHA’s eye and face protection requirements (29 CFR 1910.133), and when needed, a dust mask. 2. Do not operate near flammable liquids or in gaseous atmospheres. 3.
PAGE 4
parts diagram MODEL 400 JARVIS 6205005:::. pg 4 of 12 ® PRODUCTS CORPORATION 33 ANDERSON ROAD, MIDDLETOWN, CONNECTICUT 06457--4926 UNITED STATES OF AMERICA FAX 860--347--6978 E--MAIL. jarvis.products.corp@snet.net TEL. 860--347--7271 WWW. jarvisproducts.
PAGE 5
parts list MODEL 400 pg 5 of 12 IT. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 OLD JARVIS PART NO. PART NO.
PAGE 6
installation instructions MODEL 400 pg 6 of 12 SPECIFICATIONS Motor Power Operating Volt/Amp wire to a live terminal. If your Jarvis Wellsaw is the 115 1 hp 745 W volt model, it has a plug that looks like figure ”A”. If 230V/7.5A, 1 phase, 50/60 Hz 115V/15A, 1 phase, 50/60 Hz your Jarvis Wellsaw is the 230 volt model, it has a plug Stroke 1.
PAGE 7
general safety instructions MODEL 400 pg 7 of 12 GENERAL SAFETY INSTRUCTIONS For Operators, Employers and Maintenance Personnel WARNING: When using electric tools, basic safety precautions should always be followed to reduce the risk of fire, electric shock and personal injury, including the following: Working Precautions: 1. READ ALL INSTRUCTIONS. • Know your Jarvis Wellsaw and understand safety notices, manuals and instructions in the literature provided.
PAGE 8
operation instructions MODEL 400 pg 8 of 12 OPERATION INSTRUCTIONS B. LARGE CROSS SECTIONS: Before starting regular operation of the Jarvis Wellsaw, we recommend that you make a few cuts with a fine pitch blade to acquaint yourself with the operation of the tool before using any of the coarser blades. 1. Rocking the saw in the cut will speed up the cutting action. An 8--tooth blade is recommended. C. SINKING THE BLADE THROUGH A SURFACE: A. AVERAGE CUTTING AND RIPPING: 1.
PAGE 9
operation instructions MODEL 400 pg 9 of 12 F. HEAVY AND CONTINUOUS WOOD CUTTING: SAW: 1. For heavy or continuous wood cutting, lubricate the blade grove with oil or Jarvis Wellsaw lubricant 1062023. 2. When cutting wet or gummy wood or other material where there is a tendency for a deposit to build up on the sides of the blades, use a 50--50 mixture of kerosene and lubricating oil and place it on the sides of the blade and the blade support. JARVIS 6205005:::. G.
PAGE 10
maintenance instructions MODEL 400 pg 10 of 12 MAINTENANCE INSTRUCTIONS 7. Install handle stud (item 55) using two larger phillips screws (item 53). Always disconnect the saw from its power supply before performing any maintenance. NOTE: Your Jarvis Wellsaw is equipped with a Item numbers: refer to the parts diagram on page 4. hex key (item 20) for removing the blade. This wrench is located in the housing directly behind A. LUBRICATION: 1. The gear case should be kept 1/3 full of grease.
PAGE 11
maintenance instructions MODEL 400 pg 11 of 12 5. Use a rubber hammer and tap the end of blade towards the body of the saw until the crimp in the blade slides into the slot in the blade support. 6. Slide the blade into the push rod as far as it will go. 7. Tighten set screw (item 32) with the hex key. The set screw must be fully tightened before running the saw or damage to the saw will occur. E. GENERAL DISASSEMBLY: 1. Remove blade (item 57, 58 or 59) and blade support (item 56). 2.
PAGE 12
MODEL 400 pg 12 of 12 GENERAL SAFETY INSTRUCTIONS For Operators, Employers and Maintenance Personnel READ ALL INSTRUCTIONS BEFORE USING TOOL AND SAVE THEM FOR FUTURE REFERENCE ATTENTION: When using electric tools, basic safety precautions should always be followed to reduce the risk of potentially dangerous tools and personal injury, including the following: Working Precautions: 1. KNOW YOUR JARVIS WELLSAW.