BabyO2 TM Baby Oxygen Monitor User Manual Contact us: service@getwellue.com Website: www.getwellue.
Table of Contents 1 Tips for Safe Sleep........................................................................ 1 2 Warnings and Cautions................................................................ 1 3 Unpacking....................................................................................... 2 4 Using the device and App.............................................................3 4.1 Download App................................................................... 3 4.2 Charging....................
NOTICE The Monitor is not a medical device. It should not be used to diagnose or treat any medical condition. 1 2 Tips for Safe Sleep Room-share instead of co-sleeping Place your baby alone and on their back to sleep. Use a firm sleep surface. Keep soft objects out of crib. Use a crib that meets safty standards. Do not use cradle for sleep. Don’t use BabyO2 as an excuse for unsafe sleep.
3 this manual. Prolonged continuous monitoring may increase the risk of undesirable changes in skin characteristics, such as irritation, reddening, blistering or burns. Do not open the device cover without authorization. The cover should only be opened by a qualified service personnel.
4 Using the device and App 4.1 Download App App name: ViHealth iOS: App Store Android: Google Play Notice: if you have installed the App before, please update it to the latest version. 4.2 Charging Charge the battery before using. Connect the device to USB of computer or USB charging adapter with the supplied cable. After fully charged, the device will power off automatically. 4.3 POWER ON/OFF POWER ON: Press the side button for 2 seconds. POWER OFF: 3 ways: Press the side button for 2 seconds.
4.4 Placement Guide before working 1) Choose the wrap with appropriate size 0~3 Months, choose the smaller (for reference only) 2) Place the sensor into the wrap as shown 3) a. Position and secure the sensor Place the wrap with the sensor on the foot (either foot works), with the sensor part running on the outside edge of the foot.
b. The sensor cable should be oriented to the baby’s leg. c. The light emitter and the light detector should be opposite to each other on the two sides of the foot. For the right foot, the Light Emitter should be on the top; for the left foot, the Light Emitter should be on the bottom.
d. Attach the wrap velcro securely with no gap between the sensor and the baby’s skin 4) Plug the sensor cable into the device 5) Put the device around the leg, attach the velcro to secure the device. 4.5 Start working After the placement, press the side button for 2 seconds to power on. There should be red light inside the soft wrap. After displaying time and battery, you can change the reminder settings with side button (usually you can do nothing).
After a few seconds, readings will be displayed on the screen. If the screen display “poor signal”, please check if the sensor has been positioned and secured properly. When the above symbol displays on device screen, it indicates the readings is unavailable right now. When at rest, there will be readings in a few seconds.
4.6 Stop working & sync data Unplug the sensor cable, the countdown on the screen will begin. During the countdown, if you plug the sensor cable again, the record will be resumed. After the countdown, the data will be ready for sync. Notice: If the working time is less than 2 minute, there will be no data saved If the device power off during working, the data should have been saved. Sync data: After the countdown, run App to sync data; If app has already opened, go to History page to sync data.
To establish a Bluetooth connection, 1) Power on the device. 2) Make sure the phone Bluetooth is enabled. 3) Run the App. 4) Allow the App to use Bluetooth. Notice: DO NOT PAIR in the settings of your smartphone. 4.9 Add a new device For the initial use, you need to add a new device. 1) Turn on device, run App, select ; 2) Follow the App instruction to add the new device. 4.
You can adjust the Threshold. The reminder will stop when oxygen level recover, or you can press the side button to stop it. 4.12 Audio reminder in App You can configure it in App-Settings. You can switch on or off the reminder. You can adjust the Threshold. The volumn is same as your phone’s volume. The Reminder works only when your phone stayed in Dashboard and not locked. The Reminder in Dashboard will be activated when the oxygen level fall below the pre-set value (Threshold).
5 PC software PC Software: O2 Insight Pro Download from: www.getwellue.com Enter top menu: Support->PC Software Install the software on windows (win 7/8/10) or Mac OS(10.13 or above). To use the software, 1) Turn on device, connect the device to PC USB port with the supplied Cable. Don’t connect device to App when you want to connect to PC Software.
7 Troubleshooting Problem No readings on screen Device does not turn on or no response The app cannot find the device 8 Possible Cause the sensor is not positioned and secured properly Baby is moving frequently Battery may be low. Device might be damaged. The Bluetooth of your phone is off. The device Bluetooth is off.
shock Electro-magnetic compatibility Degree of dust & water resistance Weight Size Battery Charge time Battery life Wireless Oxygen level range Oxygen level Accuracy (Arms) Heart Rate range Heart Rate accuracy Reminder Recorded parameters Data storage Mobile App for iOS Mobile App for android Group I, Class B IP22 31g (main unit with band and sensor) 49×27×14 mm (main unit) 3.7Vdc, Rechargeable Lithiumpolymer 2-3 hours 16 hours for typical use Bluetooth 4.
Manufacturer: Shenzhen Viatom Technology Co., Ltd Address: 4E,Building 3, Tingwei Industrial Park No. 6 Liufang Road, Block 67 Xin’an Street, Baoan District Shenzhen 518101 Guangdong China Contact us: service@getwellue.com Website: www.getwellue.
