Insert wooden dowel (A) into parts (2,12) ,then secure cam bolt (B) into parts (1,19,25) with Philips head screwdriver as per diagram.
Insert wooden dowel (A) into parts (3,6,7,9) ,then secure cam bolt (B) into parts (4,6,7,9) with Philips head screwdriver as per diagram.
Pick up the slider (AA) and separate the slider arm and slider bracket for the following steps. Extend the Slide .Runner all the way forward,press the plastic release lever of the slider bracket and pull out the Slider bracket complete.
Using screw (Q) secure drawer slider (AA) to parts (17,18,23,24) with Philips head screwdriver as per diagram.
Using screw (Q) secure drawer slider (AA) to parts (6,9) with Philips head screwdriver as per diagram.
Using Cam lock(C) secure part (4) to part (3) ,part (7) to part (6) with Philips head screwdriver as per diagram.
Attach part (2) to part (7),then using Cam lock(C) secure part (12) to part (6) with Philips head screwdriver as per diagram.
Using Cam lock(C) secure parts (2,12) to part (9) ,parts (3,2) to part (3) with Philips head screwdriver as per diagram.
Using screw (F) attach part (27) to part (13) with Hex Key (H) as per diagram.
Using screw (F) attach part (13) to parts (3,6,9) with hex key (H) as per diagram.
Using bolt (G) secure plastic wedge (S) into parts (14,15,16) with Hex key (H) as per diagram.
Using bolt (G) secure plastic wedge (S) into part(16) with Hex key (H) as per diagram.
Using bolt (G) secure plastic wedge (S) into part (13) with Hex key (H)as per diagram.
Using bolt (U) secure Pulley (T) into part (11) ,and using bolt (K) secure Handle (J) into parts (11) with Philips head screwdriver as per diagram.
Pick up the door (11), and fit the pulley over the slider rails on part (2) as per diagram.
Place the plate (V) into the slider rail on the bottom panel,using screw (R) attach plate (V) to part (11) with Philips head screwdriver as per diagram. Slide the door to the left and right to make sure the door slide smoothly. If necessary adjust the screws for the door sliding smoothly.
Put parts (5,8) as per diagram.
Using Cam lock (C) secure part (1) into parts (2,3,6,9) with Philips head screwdriver as per diagram.
Using screw (L) secure plastic wedge (M) with Philips head screwdriver as per diagram.
Using screw (N) attach parts (17,18) to part (20) with Philips head screwdriver ,then put part (21) as per diagram.
Using screw (N) attach part (20) to part (22) ,then using cam lock (D) secure part (19) to parts(17,18,22) with Philips head screwdriver as per diagram.
Repeat the action as per step 20 diagram.
Repeat the action as per step 21 diagram.
Place sticker (E) cover the holes as per diagram .
Insert the assembled drawers into the unit frame, extend the Ball Bearing Slide Tracks (AA) on the pedestal Side Panel all the way forward .Then align the Slide Runners on the assembled drawers with the Slide Tracks and push the drawer carefully inside until it stops. Note : if the drawer does not go in smoothly, please take it out and repeat the step.
Insert shelf support pin (P) into parts (3,6) as per diagram. Make sure you place the shelf support pins (P) in the same level. So the shelf is not titled .Put part (10) into unit as per diagram. Tilt and rest the adjustable shelf(10) onto the shelf support pins .
Using screw (R) attach Velcro strap (Y) into part (1) with Philips head screwdriver as per diagram.
Using screw (X) attach Velcro strap (Y) into Nut (Z) to wall with Philips head screwdriver as per diagram.