Item #: ISLB8B Assembly Instructions Please visit our website for the most current instructions, assembly tips, to report damage or request parts.www.walkeredison.com Revised 06/2023 - V1 Copyright 2018, by Walker Edison Furniture Co., LLC, All rights reserved. P.
General assembly guidelines that to keep the drawers sliding smoothly. P.
Parts List Head 13 13 13 14 13 15 1 15 12 12 14 12 7 e ft L 9 3 5 11 10 6 10 10 9 4 Foot Part# 2 8 8 7 Description h R Qty Part# t ig Description Qty 1 Headboard Left Post 1 10 Central Foot 3 2 Headboard Right Post 1 11 Central Support 1 3 Footboard Left Post 1 12 Union Support 3 4 Footboard Right Post 1 13 Set Slat 4 5 Left side rail 1 14 Upper Short Slat 2 6 Right Side Rail 1 15 Upper Long Slat 2 7 Upper Rail / Lower Slat(HEADBOARD) 2
Hardware List A Bolt (Head 13) 08 pcs Ø1/4*100mm B 1/4mm Barrel nut 08 pcs C Ø10*40mm Wooden dowel 36 pcs D Ø10*30mm Wooden dowel 16 pcs Bolt (Head 13) 16 pcs E Ø7*100mm F Ø7*60mm Bolt (Head 13) 06 pcs G Ø4*35mm Screw 16 pcs H Ø4*25mm Screw 12 pcs Ø3,5*16mm Screw 08 pcs J Hex Key 01 pcs K Corner Brace 02 pcs I L Ø3/16*1 1/2 Screw 02 pcs M Ø3/16 Nut 02 pcs N Ø3/16 Washer 02 pcs Hammer recommended for assembly (not included) Phillips head and slotted head
Step 1 C C CC 36 Ø10*40mm C C C C C C C 8 2x 7 2x 14 15 2x C C 9 2x 2x C C 5 6 C C C C C C C Insert wood dowel (C) into parts (5,6,7,8,9,14 and (15). Step 2 ! E Ø7*100mm 14 J 1 J 8 7 8 Hex Key 4 1 E 7 9 J J J E 1 14 E E ! 7 7 8 8 9 HEADBOARD Secure part 1 to parts 7, 9 and 14 with screw (E) using Hex Key (J). Align dowels in part 8 to holes in part 1. P.
Step 3 E 4 Ø7*100mm J J E 1 Hex Key 2 J 14 J E J E E 7 1 7 8 9 8 E J Secure part 2 to parts 7,9 and 14 with screw (E) using Hex Key (J). Align dowels in part 8 to holes in part 2. Step 4 12 H Ø4*25mm 12 Pre Drilled Holes H 2 H H 12 H 12 12 1 HEADBOARD P.
Step 5 E J E J 1 Hex Key 14 4 J 2 Ø7*100mm E E 9 J FOOTBOARD Secure part 4 to parts 9 and 14 with screw (E) using Hex Key (J). Step 6 E 2 Ø7*100mm E J J 14 Hex Key 1 3 E J 9 4 E J FOOTBOARD Secure part 3 to parts 9 and 14 with screw (E) using Hex Key (J). P.
Step 7 I Ø3,5*16mm 4 K 1 Corner 1 IIII K 2 HEADBOARD Step 8 I Ø3,5*16mm 4 K 1 Corner I I I K I 4 IIII K 3 FOOTBOARD P.
Step 9 x A A ! J J In this step, please do not tighten the screw all the way. 1 2 A J J A B A 5 B J J A 6 A HEADBOARD Ø1/4*100mm B 1/4mm 4 J Hex Key 4 1 Secure parts 5 and 6 to headboard with screw (A) and barrel nut (B) using Hex Key (J). P.
Step 10 x A A ! J J In this step, please do not tighten the screw all the way. 3 J 5 B A 4 6 A B J A A A FOOTBOARD Ø1/4*100mm B 1/4mm 4 J Hex Key 4 1 Secure part 5 and 6 to Footboard Post (3) and (4) and Barrel nut (B) using hex key. P.
E 4 Ø7*100mm E J E 15 J E J J 15 E J A A J ! E J Finish tightening the screws from steps 9 and 10. J Secure part 15 with screw (E) using Hex Key (J). Hex Key 1 J Step 12 F F F F F J ! In this step please tighten all screws to the end. 10 F 10 10 J Secure part 11 to parts 10 with screw (F) using Hex Key (J). F Hex Key Ø7*60mm 1 6 P.
Step 13 L Ø3/16*1 1/2 2 M 2 3/16 N 2 3/16 L 11 K N M L N M 11 L N M L Secure part 11 to support (K) with screw (L) and washer (N) and nut (M) using slotted head screwdriver. Step 14 D Ø10*30mm 16 D DD D D D DD D D D D D D DD D Insert wooden dowel (D) as shown in the diagram. P.
Step 15 13 13 In this step, distribute sets of slats 13 using the applied dowels as guides. ! 13 13 13 13 Insert the set of slats 13 as shown in the diagram. P.
Step 16 G Ø4*35mm 16 G G G G 13 13 G G G G G G G G 13 G G G 13 13 G 13 P.
Step 17 2 80 lbs 280 lbs P.
