MODEL 4214, 4214T 12" VARIABLE SPEED DRILL PRESS Instruction Manual NEED HELP? CONTACT US! Have product questions? Need technical support? Please feel free to contact us: 1-800-232-1195 (M-F 8AM-5PM CST) TECHSUPPORT@WENPRODUCTS.COM IMPORTANT: Your new tool has been engineered and manufactured to WEN’s highest standards for dependability, ease of operation, and operator safety. When properly cared for, this product will supply you years of rugged, trouble-free performance.
CONTENTS WELCOME 3 Introduction...................................................................................................... 3 Specifications.................................................................................................... 3 SAFETY 4 General Safety Rules......................................................................................... 4 Specific Safety Rules for the Drill Press............................................................ 6 Electrical Information.......
INTRODUCTION Thanks for purchasing the WEN Drill Press. We know you are excited to put your tool to work, but first, please take a moment to read through the manual. Safe operation of this tool requires that you read and understand this operator’s manual and all the labels affixed to the tool. This manual provides information regarding potential safety concerns, as well as helpful assembly and operating instructions for your tool. Indicates danger, warning, or caution.
GENERAL SAFETY RULES WARNING! Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. Safety is a combination of common sense, staying alert and knowing how your item works. The term “power tool” in the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool. SAVE THESE SAFETY INSTRUCTIONS. WORK AREA SAFETY 1. Keep work area clean and well lit.
GENERAL SAFETY RULES WARNING! Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. Safety is a combination of common sense, staying alert and knowing how your item works. The term “power tool” in the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool. SAVE THESE SAFETY INSTRUCTIONS. 7.
SPECIFIC RULES FOR THE DRILL PRESS WARNING: Do not let comfort or familiarity with the product replace strict adherence to product safety rules. Failure to follow the safety instructions may result in serious personal injury. 1. TOOL PURPOSE. This drill press is designed to drill through metal and wood. Drilling through other materials could result in fire, injury, or damage to the workpiece.
SPECIFIC RULES FOR THE DRILL PRESS 12. DRILLING THE WORKPIECE. • Allow spindle to reach full speed before drilling the workpiece. • Never start the machine with the drill bit pressed against the workpiece. • Adjust the table or depth stop to avoid drilling into the table. • Set the drill press to the speed that is appropriate for the material being drilled. 13. Do not touch moving pieces. Keep hands away from the drill bit during operation.
ELECTRICAL INFORMATION GROUNDING INSTRUCTIONS In the event of a malfunction or breakdown, grounding provides the path of least resistance for an electric current and reduces the risk of electric shock. This tool is equipped with an electric cord that has an equipment grounding conductor and a grounding plug. The plug MUST be plugged into a matching outlet that is properly installed and grounded in accordance with ALL local codes and ordinances. 1. Do not modify the plug provided.
KNOW YOUR DRILL PRESS TOOL PURPOSE Drill presses are mainly used to drill clean, precise cylindrical holes into workpieces or enlarge existing holes. You may also find other uses for your drill press such as reaming, countersinking, counterboring, tapping, etc. Refer to the diagram below and on page 10 to become familiarized with the parts and controls of your drill press. 1 2 3 22 4 6 21 7 8 5 20 19 23 18 17 9 16 10 15 14 13 11 12 Fig. 2 1. 2. 3. 4. 5. 6. 7. 8.
ASSEMBLY & ADJUSTMENTS UNPACKING With the help of a friend or trustworthy foe, carefully remove the drill press from the packaging. Make sure to take out all contents and accessories. Do not discard the packaging until the drill press is completely assembled. Before using the drill press, you must assemble the unit using the instructions in this section. Check your packing list against the diagram below.
ASSEMBLY & ADJUSTMENTS WARNING: If any part is missing or damaged, do not plug the drill press in until the missing or damaged part is repaired or replaced. The column assembly (column, column support, rack, rack collar, and table support bracket) must be attached to the base. The table and table support handles must be attached to the table support bracket. The head must be attached to the column.
ASSEMBLY & ADJUSTMENTS DRILL PRESS HEAD TO COLUMN (FIG. 5) 1 WARNING: The drill press head is heavy. To avoid injury, two people should lift it into position. 1. Carefully lift the drill press head assembly (Fig. 5 - 1) and position it over the column (Fig. 5 - 2). 2. Place the mounting opening (Fig. 5 - 3) on the drill press head over the top of the column. Make sure the drill press head is seated properly on the column. 4 3 2 3.
ASSEMBLY & ADJUSTMENTS MOUNTING THE DRILL PRESS (FIG. 8) The drill press must be securely fastened through the mounting holes (Fig. 8 - 1) to a stand or workbench with heavy-duty fasteners (not included). This will prevent the drill press from tipping over, sliding, or walking during operation. 1 1 IMPORTANT: If the stand or workbench has a tendency to move during operation, fasten the workbench securely to the floor. LED BULB An LED bulb has been assembled in the socket of the head. Fig.
ASSEMBLY & ADJUSTMENTS REMOVE THE CHUCK (FIG. 10) 1 1. Turn the feed handles (1) to lower the chuck (2) to the lowest position. 2. Insert the drift key (3) into the opening in the quill. Gently tap on the wedge using a rubber mallet (4) (not included). The chuck and arbor will drop out. NOTE: To avoid possible damage to the drill or chuck, be prepared to catch the chuck as it falls. 3 4 2 Fig. 10 RAISE OR LOWER THE TABLE (FIG. 11) 1. Loosen the support lock handle (Fig.
ASSEMBLY & ADJUSTMENTS INSTALL THE TABLE EXTENSION (FIG. 12B) 1. Insert the two rods (Fig. 12B - 1) of the table extension into the two channels (Fig. 12B - 2) at the side of the table. 2. Place a wing knob (Fig. 12B - 3) in the opening on the bottom of each channel and tighten to secure the extension to the table. 2 3 1 WARNING: To avoid injury, make sure the chuck key is removed from the chuck before starting any drilling operation. Fig. 12B INSTALLING A DRILL BIT (FIG. 13) 1.
ASSEMBLY & ADJUSTMENTS ADJUSTING THE LASER (FIG. 15 & 16) WARNING: Do not stare directly at the laser beam. Observe all safety rules. • Never aim the beam at a person or an object other than the workpiece. • Always make sure the laser beam is aimed at a workpiece that does not have reflective surfaces, as the laser beam could reflect into your eyes or the eyes of others. 1. Place a workpiece on the table. 2. Turn the laser switch (Fig. 15 - 1) to the ON position. 1 3.
ASSEMBLY & ADJUSTMENTS SPINDLE RETURN SPRING (FIG. 17) The spindle is equipped with an auto-return mechanism. The main components are a spring and a notched housing. The spring was properly adjusted at the factory and should not be readjusted unless absolutely necessary. 4 1 5 2 1. Unplug the drill press. 3 2. Place a screwdriver into the loop (Fig. 17 - 1) to hold the spring in place. 3. Loosen the two housing nuts (Fig. 17 - 2) approximately 1/4" (6 mm).
ASSEMBLY & ADJUSTMENTS DRILL PRESS ON / OFF SWITCH (FIG. 19) 1. To turn the drill press ON, insert the yellow safety key (Fig. 19 - 1) into the switch housing (Fig. 19 - 2). As a safety feature, the switch cannot be turned ON without the safety key. 2. Flip the switch upward to the ON position. 2 3 5 3. To turn the drill press OFF, flip the switch downward. 1 3 4. To lock the switch in the OFF position, remove the safety key (Fig. 19 - 1) from the switch.
OPERATION GENERAL DRILLING GUIDELINES - DRILLING A HOLE WARNING: To prevent the workpiece and the backup material from slipping from your hand while drilling, position the workpiece and backup material to the left side of the column. If the workpiece and the backup material are not long enough to reach the column, clamp the workpiece and backup material to the table. Failure to do this could result in personal injury. 1.
OPERATION DEPTH SCALE METHOD (FIG. 21B) 1. Make sure the 0 (in or mm) mark on the depth gauge rests at the top edge of the metal support (Fig. 21B - 4) when the quill is fully retracted. 1 2. Put the workpiece on the table and raise the table until the tip of the drill bit just touches the top of the workpiece. Lock the table in place. 3 2 4 3. Determine the drill depth for this workpiece. Fig. 21B 4. Rotate the depth knob (Fig. 21B - 2) until it is aligned with the desired depth mark (Fig.
OPERATION DRILLING METAL • Use metal-piercing twist drill bits. • It is always necessary to lubricate the tip of the drill with oil to prevent overheating of the drill bit. • All metal workpieces should be clamped down securely. Any tilting, twisting, or shifting causes a rough drill hole, and increases the potential of drill bit breakage. • Never hold a metal workpiece with your bare hands. The cutting edge of the drill bit may seize the workpiece and throw it, causing serious injury.
OPERATION DRILL BIT SIZE RECOMMENDATIONS RPM 2000 to 3200 1400 to 2000 1000 to 1400 800 to 1000 580 to 800 Wood 3/8 in. 5/8 in. 7/8 in. 1-1/4 in. 1-5/8 in. 9.5 mm 16 mm 22 mm 31.75 mm 41.4 mm Aluminum, Zinc, Brass 7/32 in. 5.6 mm 11/32 in. 8.75 mm 15/32 in. 12 mm 11/16 in. 17.5 mm 3/4 in. 19 mm Iron, Steel 3/32 in. 2.4 mm 5/32 in. 4 mm 1/4 in. 6.4 mm 3/8 in. 9.5 mm 5/8 in. 16 mm Recommended speed for drill bit size and materials REPLACING THE BELT (FIG.
MAINTENANCE WARNING: To avoid accidents, turn OFF and unplug the tool from the electrical outlet before cleaning, adjusting, or performing any maintenance or lubrication work. WARNING: Any attempt to repair or replace electrical parts on this tool may be hazardous. Servicing of the tool must be performed by a qualified technician. When servicing, use only identical WEN replacement parts. Use of other parts may be hazardous or induce product failure.
TROUBLESHOOTING WARNING: Stop using the tool immediately if any of the following problems occur. Repairs and replacements should only be performed by an authorized technician. For any questions, please contact our customer service at (800) 232-1195, M-F 8-5 CST or email us at techsupport@wenproducts.com. PROBLEM SOLUTION 1) Incorrect belt tension 2) Dry spindle 3) Loose spindle pulley 4) Loose motor pulley 5) Seized motor pulley 1) Adjust the belt tension.
TROUBLESHOOTING ASSEMBLY & ADJUSTMENTS WARNING: Stop using the tool immediately if any of the following problems occur. Repairs and replacements should only be performed by an authorized technician. For any questions, please contact our customer service at (800) 232-1195, M-F 8-5 CST or email us at techsupport@wenproducts.com. PROBLEM CAUSE SOLUTION Drill bit binds in the workpiece 1) The workpiece is pinching the bit 2) Excessive feed pressure 1) Support or clamp the workpiece. 2) Feed more slowly.
EXPLODED & PARTS LIST ASSEMBLYVIEW & ADJUSTMENTS 34 1 68 125 2 4 A 3 124 31 70 66 67 6 5 43 71 69 110 7 18 8 B 9 L 17 19 10 11 21 12 73 112 20 77 113 114 29 13 P 67 86 80 14 15 35 23 24 30 3 31 N 53 72 52 56 54 87 55 88 89 90 38 39 96 97 63 42 48 45 47 129 17 122 100 F 50 123 49 119 99 102 83 103 E 108 G 127 128 107 131 109 82 R H 98 99 76 51 71 104 65 49 Q 106 105 64 46 78 101 44 136 118 93 94 95 92 60 D 76 79 62 39
EXPLODED & PARTS LIST ASSEMBLYVIEW & ADJUSTMENTS NOTE: Parts may only be available in their respective subassemblies. Not all parts may be available for purchase. NO. PART NO. DESCRIPTION QTY NO. A - SPINDLE PULLEY ASSEMBLY (PART 4214B-AA) PART NO.
EXPLODED & PARTS LIST ASSEMBLYVIEW & ADJUSTMENTS NO. 28 PART NO. DESCRIPTION QTY NO. PART NO.
WARRANTY STATEMENT ASSEMBLY & ADJUSTMENTS WEN Products is committed to building tools that are dependable for years. Our warranties are consistent with this commitment and our dedication to quality. LIMITED WARRANTY OF WEN CONSUMER POWER TOOLS PRODUCTS FOR HOME USE GREAT LAKES TECHNOLOGIES, LLC (“Seller”) warrants to the original purchaser only, that all WEN consumer power tools will be free from defects in material or workmanship for a period of two (2) years from date of purchase.
NOTES 30
NOTES 31
THANKS FOR REMEMBERING V. 2021.03.