MODEL 23006 CORDLESS ROTARY TOOL For replacement parts visit WENPRODUCTS.COM 3065544 IMPORTANT: Your new tool has been engineered and manufactured to WEN’s highest standards for dependability, ease of operation, and operator safety. When properly cared for, this product will supply you years of rugged, trouble-free performance. Pay close attention to the rules for safe operation, warnings, and cautions.
TABLE OF CONTENTS Specifications..................................................................................2 Introduction.....................................................................................3 Important Safety Rules.....................................................................4 Rotary Tool Safety Rules...................................................................6 Know Your Rotary Tool & Accessories................................................7 Preparation & Assembly....
INTRODUCTION Thanks for purchasing the WEN Rotary Tool. We know you are excited to put your tool to work, but first, please take a moment to read through the manual. Safe operation of this tool requires that you read and understand this operator’s manual and all the labels affixed to the tool. This manual provides information regarding potential safety concerns, as well as helpful assembly and operating instructions for your tool. SAFETY ALERT SYMBOL: Indicates danger, warning, or caution.
ROTARY TOOL SAFETY RULES Safety is a combination of common sense, staying alert and knowing how your item works. SAVE THESE SAFETY INSTRUCTIONS. WARNING: Read and understand all warnings, cautions and operating instructions before using this tool. Failure to follow all instructions listed below may result in personal injury and tool damage. OPERATING ENVIRONMENT 1. Keep the tool away from water. Do not expose the tool to rain or wet conditions.
ROTARY TOOL SAFETY RULES ROTARY TOOL ACCESSORIES 1. The rotary tool accessory must have a rated speed higher than 25,000 RPM (the maximum operating speed of your rotary tool), otherwise there is a risk of injury. 2. The spindle diameter of the accessory bit must match the size of the collet. The included collet size is 1/8 inch (3.2 mm); collets of other sizes may be purchased separately depending on the spindle diameter of the accessory. 3.
ROTARY TOOL SAFETY RULES ROTARY TOOL MAINTENANCE 1. Battery tools do not need to be plugged into an electrical outlet, therefore they are always ready to operate. Beware of the possible hazards when not using your battery tool or when changing accessories. Following this rule will reduce the risk of electric shock, fire or personal injury. 2. Always turn off the machine before making adjustments or changing attachments. Such preventive safety measures reduce the risk of starting the power tool accidentally.
ROTARY TOOL SAFETY RULES VIBRATION SAFETY This tool vibrates during use. Repeated or long-term exposure to vibration may cause temporary or permanent physical injury, particularly to the hands, arms and shoulders. To reduce the risk of any vibrationrelated injury: 1. First be examined by a doctor and then have regular medical check-ups to ensure medical problems are not being caused or worsened from use.
KNOW YOUR ROTARY TOOL & ACCESSORIES Carefully unpack the tool and accessories. Check all components and compare against the list below. If any part is damaged or missing, please contact our customer service at (800) 232-1195, M-F 8-5 CST or email techsupport@wenproducts.com. ROTARY TOOL ASSEMBLY Battery Pack Alignment Indication Arrows Power & Speed Switch Spindle Lock Locking Collar Ventilation Holes Collet Nut ROTARY TOOL ACCESSORIES 1. 2. 1. 2. 3. 4. 8 3. 4. 1pc Collet (Ø1/8"/3.
KNOW YOUR ROTARY TOOL & ACCESSORIES No. 1 Accessory Collet (Ø1/8) Explanation & Applications Installs into the tool's spindle for holding a rotary tool bit in place. Your tool comes with one Ø1/8"collet. The shank diameter of the rotary tool bit must match the size of the collet. • Use the front of the wrench for loosening/tightening the collet nut to remove/install rotary tool bits or to change collets.
PREPARATION & ASSEMBLY WARNING: To avoid injuries from accidental startups, always ensure that the tool is switched OFF and the battery pack is removed before making adjustments or changing accessories. INSTALLING SANDING BANDS (FIG. 1) 1. Loosen the flat-head screw on the top of the sanding drum using the back of the included 2-in-1 wrench. Sanding Drum Mandrel Sanding Band 2. Slide the sanding band onto the sanding drum. 3. Secure the sanding drum in place by tightening the screw.
PREPARATION & ASSEMBLY WARNING: Follow the safety instructions when handling batteries. • Do not mix batteries of different types or different brands. Do not mix old and new batteries. • Do not short circuit batteries. • Do not keep batteries near fire, sources of heat, or use in direct sunlight. • Remove batteries from tool when not being used to an extended period of time. • Never handle leaked batteries. Do not dismantle batteries. • Recycle used tool and batteries at your local recycling facility.
OPERATION WARNING: Read and thoroughly understand all instructions and safety information before operating this rotary tool. Failure to do so may cause personal injuries. WARNING: Always wear ANSI Z87.1-approved safety glasses, safety gloves and suitable work clothing. Do not wear jewelry or other loose clothing which could get caught in moving parts. Hold the tool away from your face and body in case parts and chips fly out unexpectedly during operation. TURNING ON/OFF & SELECTING SPEED (FIG.
MAINTENANCE WARNING: To prevent accidental startups, always turn OFF and remove the battery pack from the tool before cleaning or performing maintenance. IMPORTANT: Servicing of the tool requires extreme care and knowledge and should be performed only by a qualified service technician using identical replacement parts. CLEANING & INSPECTION 1. After each use, clean the tool and accessories using a clean cloth or a soft brush. You can also use low pressure compressed dry air to blow away dust from the tool.
EXPLODED VIEW & PARTS LIST 14
EXPLODED VIEW & PARTS LIST No. Part No. Description Qty. 1 23006-001 Collet Nut 1 2 23006-002 Collet (1/8”/3.2 mm) 1 3 23006-003 Locking Collar 1 4 23006-004 Spindle Assembly 1 4.1 23006-004.1 Spindle 1 4.2 23006-004.2 Bearing 695Z 1 4.3 23006-004.3 Brake Bushing 1 5 23006-005 Spindle Lock Assembly 1 5.1 23006-005.1 Spindle Lock Button 1 5.2 23006-005.2 Spindle Lock 1 6 23006-006 Spindle Lock Spring 1 7 23006-007 Circlip 65Mn 1 8.1 23006-008.
WARRANTY STATEMENT WEN Products is committed to building tools that are dependable for years. Our warranties are consistent with this commitment and our dedication to quality. LIMITED WARRANTY OF WEN CONSUMER POWER TOOLS PRODUCTS FOR HOME USE GREAT LAKES TECHNOLOGIES, LLC (“Seller”) warrants to the original purchaser only, that all WEN consumer power tools will be free from defects in material or workmanship for a period of two (2) years from date of purchase.
