VARIABLE SPEED ROTARY TOOL WITH CASE AND FLEX SHAFT 3065544 Model # 23114 For replacement parts visit WENPRODUCTS.COM bit.ly/wenvideo IMPORTANT: Your new tool has been engineered and manufactured to WEN’s highest standards for dependability, ease of operation, and operator safety. When properly cared for, this product will supply you years of rugged, trouble-free performance. Pay close attention to the rules for safe operation, warnings, and cautions.
TABLE OF CONTENTS Product Specifications Safety Introduction General Safety Rules Electrical Information Rotary Tool Safety Rules Know Your Rotary Tool Know Your Accessories Assembly & Adjustments Operation Maintenance Exploded View & Parts List Warranty Statement 2 3 4 6 7 8 9 12 14 15 16 17 PRODUCT SPECIFICATIONS Model Number: Motor: Speed: Collet Size: Product Dimensions: Product Weight: 23114 120V, 60 Hz, 1.4A 8,000 - 35,000 RPM 1/8 in. (3.2 mm) 3/32 in. (2.4 mm) 1/16 in. (1.
SAFETY INTRODUCTION Thanks for purchasing the WEN Rotary Tool. We know you are excited to put your tool to work, but first, please take a moment to read through the manual. This manual provides information regarding potential safety concerns, as well as helpful assembly and operating instructions. Safe operation of this tool requires that you read and understand this operator’s manual and all labels affixed to the tool. SAFETY ALERT SYMBOL: Indicates danger, warning, or caution.
GENERAL SAFETY RULES Safety is a combination of common sense, staying alert and knowing how your item works. SAVE THESE SAFETY INSTRUCTIONS. WARNING! Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and serious injury. To avoid mistakes and serious injury, do not plug in your tool until the following steps have been read and understood. WORK AREA SAFETY 1. Keep work area clean and well lit.
GENERAL SAFETY RULES POWER TOOL USE AND CARE 1. Avoid accidental start-ups. Make sure the power switch is in the OFF position before connecting the plug to a power source or carrying the tool. 2. Check power tool for damaged parts. Check for misalignment of moving parts, jamming, breakage, improper mounting, or any other conditions that may affect the tool’s operation. Do not use the power tool if the switch does not turn ON/OFF. Any part that is damaged should be properly repaired or replaced before use.
ELECTRICAL INFORMATION DOUBLE INSULATION Double insulation is a concept in safety in electric power tools, where two systems of insulation are provided. This eliminates the need for the usual three-wire grounded power cord. All exposed metal parts are isolated from the internal metal motor components with protecting insulation. Double insulated tools do not need to be grounded.
ROTARY TOOL SAFETY RULES WARNING: Read and understand all warnings, cautions and operating instructions before using this equipment. Failure to follow all instructions listed below may result in personal injury and tool damage. WORK ENVIRONMENT • Do not operate the tool in wet or damp conditions; doing so significantly increases the risk of electrical shock. • Do not operate the tool in the presence of flammable liquids or gases.
ROTARY TOOL SAFETY RULES (Continued) TURNING ON THE TOOL Before turning on the rotary tool, ensure that it is completely clear of the workpiece. Let the tool reach full speed before making contact with the workpiece. DURING OPERATION • Do not apply excessive pressure to the tool or attempt to make an excessive depth of cut. Overstressing the tool may cause kickback and damage the tool and accessories. • Use special care when working corners, sharp edges etc. Avoid bouncing and snagging the accessory.
KNOW YOUR ACCESSORIES INCLUDED ACCESSORIES: 1. 7. 2. 8. 3. 9. 13. 18. 4. 10. 14. 19. 5. 11. 12. 15. 16. 20. 6. 17. 21. 22. No. Description Qty. No. Description Qty.
KNOW YOUR ACCESSORIES Refer to the chart below for explanations and recommended applications for your rotary tool accessory bits. No. Accessory Explanation & Applications 1 Collet (Ø1/8", Ø3/32", Ø1/16") For holding a rotary tool bit in place. Your tool comes with Ø1/8", Ø3/32", Ø1/16" sized collets. Always use the correct collet size that matches the shank diameter of the rotary tool bit.
KNOW YOUR ACCESSORIES No. 13 Accessory Grinding Stone Bit (Ø1/8") Explanation & Applications Bits of various shapes used for grinding and abrasive operations. Great for removing flash from metal castings, deburring metal after cutting, smoothing welded joints, grinding off rivets and removing rust. Can be sharpened with No. 6 Dressing Stone. 14 Drill Bit (Ø1/8", Ø3/32", Ø1/16") Drill into materials such as metal, hardwood, and plastics. Make sure to use the correct size collet for your drill bit.
ASSEMBLY & ADJUSTMENTS WARNING: To avoid injury from accidental startups, always ensure that the tool is switched OFF and unplugged from the power supply before making adjustments or changing accessories. INSTALLING WHEEL/DISC ACCESSORIES (Fig. 1) Loosen and remove the screw at the top of the small screw mandrel. Remove the top red ring from the screw and slide the wheel or sanding disc above the bottom red ring (ensure the abrasive side of the disc is facing up for sanding disc).
ASSEMBLY AND ADJUSTMENTS ATTACHING THE FLEX SHAFT (Fig. 5 - 14) FOR VIDEO INSTRUCTIONS ON ATTACHING THE FLEX SHAFT, VISIT: http://bit.ly/wenflexshaft 1. Unscrew and remove the locking collar from the end of the rotary tool (Fig. 5). 2. Use the 1/8" collet for attaching the flex shaft. Press down on the spindle lock button (Fig. 6) to unscrew the collet nut and check the collet size. Replace the collet nut. Fig. 5 Fig. 6 Fig. 7 Fig. 8 3.
OPERATION WARNING: Read and thoroughly understand all instructions and safety information before operating this rotary tool. Failure to do so may cause serious injury. ADJUSTING THE SPEED OF THE ROTARY TOOL (Fig. 15) The variable speed adjustment wheel on the top of the rotary tool is used to set the desired rotation speed. The speed for your rotary tool ranges from 8,000 to 35,000 RPM. To increase the speed, turn the wheel forward to a higher number.
MAINTENANCE WARNING: Always switch OFF and disconnect the rotary tool from the power supply before carrying out any adjustments, service or maintenance. IMPORTANT: Servicing of the tool requires extreme care and knowledge and should be performed only by a qualified service technician. CLEANING AND INSPECTION 1. After each use, clean the tool and accessories using a clean cloth or a soft brush. NEVER use water or other liquids to clean the electrical portions of the tool. 2.
EXPLODED VIEW & PARTS LIST No. 1 2 3 4 5 6 7 8 9 10 11 16 Part No. 23114-001 23114-002 23114-003 23114-004 23114-005 23114-006 23114-007 23114-008 23114-009 23114-010 23114-011 Description Collet Nut Collet Nose Cap Spindle Lock Button Ø 8 Base Bearing Fan Rotor Left Body Carbon Brush Screw Qty 1 1 1 1 1 1 1 1 1 2 6 No. 12 13 14 15 16 17 18 19 20 21 22 Part No.
LIMITED ONE YEAR WARRANTY WEN Products is committed to building tools that are dependable for years. Our warranties are consistent with this commitment and our dedication to quality. LIMITED WARRANTY OF WEN CONSUMER POWER TOOLS PRODUCTS FOR HOME USE.: GREAT LAKES TECHNOLOGIES, LLC (“Seller”) warrants to the original purchaser only, that all WEN consumer power tools will be free from defects in material or workmanship for a period of one (1) year from date of purchase.
THANKS FOR REMEMBERING