VARIABLE SPEED ROTARY TOOL KIT 3065544 Model # 23190 For replacement parts visit WENPRODUCTS.COM bit.ly/wenvideo IMPORTANT: Your new tool has been engineered and manufactured to WEN’s highest standards for dependability, ease of operation, and operator safety. When properly cared for, this product will supply you years of rugged, trouble-free performance. Pay close attention to the rules for safe operation, warnings, and cautions.
TABLE OF CONTENTS Product Specifications Safety Introduction General Safety Rules Rotary Tool Safety Rules Electrical Information Know Your Rotary Tool Know Your Accessories Assembly & Adjustments Operation Maintenance Warranty Statement Exploded View & Parts List 2 3 4 6 8 9 10 14 15 16 17 18 PRODUCT SPECIFICATIONS Model Number: Motor: Speed: Collet Sizes: Product Weight: 23190 120V, 60 Hz, 1.3A 8,000 to 35,000 RPM 1/8”, 3/32” & 1/16” (1.6 mm, 2.3 mm and 3.2 mm) 1.
SAFETY INTRODUCTION Thanks for purchasing the WEN Rotary Tool Kit. This is an exciting moment. You have received your new tool, opened the box, and are now about to read through the instruction manual. This manual provides information regarding potential safety concerns, as well as helpful assembly and operating instructions. Safe operation of this tool requires that you read and understand this operator’s manual and all labels affixed to the tool. SAFETY ALERT SYMBOL: Indicates danger, warning, or caution.
GENERAL SAFETY RULES Safety is a combination of common sense, staying alert and knowing how your item works. SAVE THESE SAFETY INSTRUCTIONS. WARNING! Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and serious injury. To avoid mistakes and serious injury, do not plug in your tool until the following steps have been read and understood. WORK AREA SAFETY 1. Keep work area clean and well lit.
GENERAL SAFETY RULES POWER TOOL USE AND CARE 1. Avoid accidental start-ups. Make sure the power switch is in the OFF position before connecting the plug to a power source or carrying the tool. 2. Check power tool for damaged parts. Check for misalignment of moving parts, jamming, breakage, improper mounting, or any other conditions that may affect the tool’s operation. Do not use the power tool if the switch does not turn ON/OFF. Any part that is damaged should be properly repaired or replaced before use.
ROTARY TOOL SAFETY RULES WARNING: Read and understand all warnings, cautions and operating instructions before using this equipment. Failure to follow all instructions listed below may result in personal injury and tool damage. 1. WORK ENVIRONMENT • Do not operate the tool in wet or damp conditions; doing so significantly increases the risk of electrical shock. • Do not operate the tool in the presence of flammable liquids or gases. 2.
ROTARY TOOL SAFETY RULES 10. DURING OPERATION • Do not apply excessive pressure to the tool or attempt to make an excessive depth of cut. Overstressing the tool may cause kickback and damage the tool and accessories. • Use special care when working corners, sharp edges etc. Avoid bouncing and snagging the accessory. • Never touch any moving parts of the tool by hand. • Never press in the spindle lock button when the rotary tool is running. 11. TURNING OFF THE TOOL.
ELECTRICAL INFORMATION DOUBLE INSULATION Double insulation is a concept in safety in electric power tools, where two systems of insulation are provided. This eliminates the need for the usual three-wire grounded power cord. All exposed metal parts are isolated from the internal metal motor components with protecting insulation. Double insulated tools do not need to be grounded, nor should a means for grounding be added to the product.
KNOW YOUR ROTARY TOOL Carefully unpack the tool from the packaging. Check all components and compare against the diagram below. If any part is damaged or missing, please contact our customer service at (800) 232-1195, M-F 8-5 CST or email us at techsupport@wenproducts.com. Hanger Variable Speed Wheel Carbon Brush Cover (Top and Bottom) Ventilation Slots Spindle Lock Button Flex Shaft Locking Collar Collet Nut Steady Grip Attachment ON/OFF Switch (underside) STEADY GRIP HANDLE ATTACHMENT (Fig.
KNOW YOUR ACCESSORIES INCLUDED ACCESSORIES: 1. 2. 8. 9. 4. 10. 13. 14. 19. 20. 5. 11. 7. 12. 15. 21. 6. 16. 22. 17. 23. 18. 24. No. Description Qty. No. Description Qty.
KNOW YOUR ACCESSORIES Refer to the chart below for explanations and recommended applications for your rotary tool accessory bits. No. Accessory Explanation & Applications 1 For holding a rotary tool bit in place. Your tool comes with Ø1/8", Ø3/32", Collet Ø1/16" sized collets. Always use the correct collet size that matches the shank (Ø1/8", Ø3/32", Ø1/16") diameter of the rotary tool bit. 2 Slides over the top of the sanding drum mandrel to sand and smooth around surfaces and inside curves.
KNOW YOUR ACCESSORIES No. 12 Accessory Grinding Stone Bit (Ø1/8") Explanation & Applications •Aluminum Oxide Grinding Stone Bit (Orange): Bits of various shapes used for grinding and abrasive operations. Great for removing flash from metal castings, deburring metal after cutting, smoothing welded joints, grinding off rivets and removing rust. •Silicon Carbide Grinding Stone Bit (Green): For tougher materials such as glass and ceramics. Attach to No. 8 Small Screw Mandrel (see page 13).
ASSEMBLY AND ADJUSTMENTS WARNING: To avoid injury from accidental startups, always ensure that the tool is switched OFF and unplugged from the power supply before making adjustments or changing accessories. INSTALLING WHEEL/DISC ACCESSORIES (Fig. 3) Small Screw Mandrel Sanding Disc or Loosen and remove the screw at the top of the small screw mandrel.
ASSEMBLY AND ADJUSTMENTS ATTACHING THE FLEX SHAFT (Fig. 7 - 16) FOR VIDEO INSTRUCTIONS ON ATTACHING THE FLEX SHAFT, VISIT: http://bit.ly/wenflexshaft 1. Unscrew and remove the locking collar from the end of the rotary tool (Fig. 7). 2. Use the 1/8" collet for attaching the flex shaft. Press down on the spindle lock button (Fig. 8) to unscrew the collet nut and check the collet size. Replace the collet nut. Fig. 7 Fig. 8 Fig. 9 Fig. 10 3.
OPERATION WARNING: Read and thoroughly understand all instructions and safety information before operating this rotary tool. Failure to do so may cause serious injury. ADJUSTING THE SPEED OF THE ROTARY TOOL (Fig. 17) The variable speed adjustment wheel on the top of the rotary tool is used to set the desired rotation speed. The speed for your rotary tool ranges from 8,000 to 35,000 RPM. To increase the speed, turn the wheel forward to a higher number.
MAINTENANCE WARNING: Always switch OFF and disconnect the rotary tool from the power supply before carrying out any adjustments, service or maintenance. IMPORTANT: Servicing of the tool requires extreme care and knowledge and should be performed only by a qualified service technician. CLEANING AND INSPECTION 1. After each use, clean the tool and accessories using a clean cloth or a soft brush. NEVER use water or other liquids to clean the electrical portions of the tool. 2.
LIMITED ONE YEAR WARRANTY WEN Products is committed to building tools that are dependable for years. Our warranties are consistent with this commitment and our dedication to quality. LIMITED WARRANTY OF WEN CONSUMER POWER TOOLS PRODUCTS FOR HOME USE GREAT LAKES TECHNOLOGIES, LLC (“Seller”) warrants to the original purchaser only, that all WEN consumer power tools will be free from defects in material or workmanship for a period of one (1) year from date of purchase.
EXPLODED VIEW AND PARTS LIST 18
EXPLODED VIEW AND PARTS LIST No. Part No.
THANKS FOR REMEMBERING
