Product Manual

ManualsBrandsWEN ManualsAccessoriesBaker Scaffold Outriggers with 5-Inch Locking Casters, 4 Pack

OUTRIGGER SET SAFETY

WORK AREA SAFETY

1. Keep your work area clean, uncluttered, and well lit.

Cluttered areas invite injuries and accidents. Keep the

ground clear of tripping hazards. Do not work on ﬂoor

surfaces that are slippery with sawdust or wax.

2. Observe work area conditions. Keep bystanders at a

safe distance from the work area. Never allow children

or pets near the tool.

3. To avoid contact and shock hazard, do not use the

scaffolding near energized power lines or electrical

lines. Do not contact unprotected, energized electrical

power lines or other power sources with the scaffolding

or tools. Maintain at least 10 feet from electrical lines.

Consult the power company to shut off the power or in-

sulate/relocate lines if a job requires working closer than

10 feet to electrical lines.

4. Only assemble and use the scaffolding on a ﬂat, level

surface capable of supporting the tool with its maximum

capacity load. It is easy to lose control if attempting to

pull a load on a sloping or uneven surface.

PERSONAL SAFETY

1. Wear ANSI Z87.1-approved impact safety goggles, a

hard hat, heavy-duty work gloves and OSHA-speciﬁed

safety harness during assembly and use. Wear addi-

tional safety gear as required by local, state and federal

regulations.

2. Dress for safety. Do not wear loose clothing, neckties,

or jewelry (rings, watches, etc.) Always wear non-slip

footwear and tie back long hair.

3. Stay alert - watch what you’re doing and use com-

mon sense when using the scaffolding. Do not use while

you are tired or under the inﬂuence of drugs, alcohol or

medication that may affect your ability to properly use

the tool. A moment of inattention while using the scaf-

fold may result in serious personal injury.

SCAFFOLDING USE & CARE

1. Follow all current OSHA (Occupational Safety and

Health Administration) guidelines for setup, use and

maintenance of the scaffolding. Scaffolding safety regu-

lations may change periodically. The operator is respon-

sible for being familiar with and obeying current OSHA

guidelines as well as local, state and federal regulations

regarding the set-up and use of this product.

2. Use the right product for the job. There are certain

applications for which this tool was designed. Unauthor-

ized modiﬁcation may damage the tool and/or cause per-

sonal injuries.

3. Check for damaged or worn out parts before using the

scaffolding. Check for alignment of moving parts, jam-

ming, breakage, improper mounting, or any other condi-

tions that may affect the tool’s operation. Any part that is

damaged should be properly repaired or replaced before

use. Do not attempt to straighten deformed parts, as this

will weaken their structural integrity. Bent parts should

be replaced immediately.

4. Make sure all guards and fasteners are secure after

assembly or adjustments. All connections should be

tight before operation.

5. Acids and other corrosive substances may severely

affect the integrity of the scaffolding. Use extreme care

around such materials and follow applicable instruc-

tions. Do not use acids or other corrosive substances on

scaffolding parts, as they could corrode the metal and

decrease its strength.

6. Immediately remove scaffolding from use and discard

if exposed to excessive heat (such as ﬁre), which could

cause a loss of structural integrity.

7. Do not permit oil, grease, or other slippery material to

accumulate on climbing or gripping surfaces.

8. Do not use the product if the platform surface is dam-

aged or has deteriorated. Only use the included platform

or an identical replacement platform. The platform must

not extend beyond the base support.

SCAFFOLDING & ACCESSORY SAFETY WARNINGS

WARNING! Do not operate the power tool until you have read and understood the following instructions and

the warning labels.