VARIABLE SPEED JIG SAW 3087464 Model # 33606 For replacement parts visit WENPRODUCTS.COM bit.ly/wenvideo IMPORTANT: Your new tool has been engineered and manufactured to WEN’s highest standards for dependability, ease of operation, and operator safety. When properly cared for, this product will supply you years of rugged, trouble-free performance. Pay close attention to the rules for safe operation, warnings, and cautions.
TABLE OF CONTENTS Technical Data Safety Introduction General Safety Rules Specific Rules for Your Jig Saw Electrical Information Know Your Jig Saw Assembly & Adjustments Operation Maintenance Warranty Statement Exploded View and Parts List 2 3 4 6 8 9 10 13 14 15 16 TECHNICAL DATA Model Number: Motor: Variable Speed: Wood Cutting Capacity: Metal Cutting Capacity: Bevel Angle: Dust Port Outer Diameter: Assembled Dimensions: Product Weight: 33606 AC 120V, 60Hz, 6.6A 0 to 3300 SPM 4-1/4 in. (110 mm) 3/8 in.
SAFETY INTRODUCTION Thanks for purchasing the WEN Jig Saw. If you like a portable tool that can create both straight and curved cuts on different materials, then this is the right product for you. This manual provides information regarding potential safety concerns, as well as helpful assembly and operating instructions. Safe operation of this tool requires that you read and understand this operator’s manual and all labels affixed to the tool.
GENERAL SAFETY RULES Safety is a combination of common sense, staying alert and knowing how your item works. SAVE THESE SAFETY INSTRUCTIONS. WARNING! Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and serious injury. To avoid mistakes and serious injury, do not plug in your tool until the following steps have been read and understood. WORK AREA SAFETY 1. Keep work area clean and well lit.
GENERAL SAFETY RULES POWER TOOL USE AND CARE 1. Avoid accidental start-ups. Make sure the power switch is in the OFF position before connecting the plug to a power source or carrying the tool. 2. Check power tool for damaged parts. Check for misalignment of moving parts, jamming, breakage, improper mounting, or any other conditions that may affect the tool’s operation. Do not use the power tool if the switch does not turn ON/OFF. Any part that is damaged should be properly repaired or replaced before use.
SPECIFIC RULES FOR YOUR JIG SAW WARNING: Do not let comfort or familiarity with the product replace strict adherence to product safety rules. Read and understand all warnings, cautions and operating instructions before using this equipment. Failure to follow all instructions listed below may result in personal injury and tool damage. 1. WORK ENVIRONMENT. Do not operate the tool in wet or damp conditions; doing so significantly increases the risk of electrical shock.
SPECIFIC RULES FOR YOUR JIG SAW 11. MAKING ADJUSTMENTS. Always turn off and unplug the jig saw before making adjustments or changing attachments. Accidental start-ups may occur if the jig saw is plugged in during an accessory change. Do not touch the attachment immediately after operation. Allow time for the attachment to cool and calm down before removing it. 12. TOOL MAINTENANCE. Develop a periodic maintenance schedule for your tool. Follow the instructions for lubrication, storage changing accessories.
ELECTRICAL INFORMATION DOUBLE INSULATION Double insulation is a concept in concept in electrical power tool safety, where two systems of insulation are provided. This eliminates the need for the usual three-wire grounded power cord. All exposed metal parts are isolated from the internal metal motor components with protecting insulation. Double insulated tools do not need to be grounded.
KNOW YOUR JIG SAW Carefully unpack the tool from the packaging. Check all components and compare against the graph below. If any part is damaged or missing, please contact our customer service at (800) 232-1195, M-F 8-5 CST or email us at techsupport@wenproducts.com.
ASSEMBLY AND ADJUSTMENTS WARNING: To avoid injury from accidental startups, be sure that the tool is switched off and disconnected from the power supply before inspecting the unit, making adjustments or changing accessories. INSTALLING/REPLACING THE JIG SAW BLADE (Fig. 1 to 3) The jig saw is capable of cutting a variety of materials when fitted with the correct blade. Always select the suitable blade for your operation. Your jig saw comes with a wood-cutting blade and a metal-cutting blade.
ASSEMBLY AND ADJUSTMENTS SETTING THE BLADE ORBITAL ACTION (Fig. 4) The blade orbit selector lever controls the blade orbit travel distance. There are 4 settings, indicated on the side housing (Fig. 4). At the 0 setting, the blade moves up and down in a straight line for smooth cutting. At the 3 setting, the blade moves in an elliptical stroke for fast, aggressive cutting. Maximum cutting efficiency can be obtained by adjusting the blade orbit selector lever to suit the material being cut.
ASSEMBLY AND ADJUSTMENTS ADJUSTING THE BEVEL ANGLE (Fig. 8 & 9) The base plate of your jig saw is pre-adjusted to 0° for making straight cuts. You can create bevel cuts by setting the base plate up to 45° to the left or right. To adjust the angle of the base plate: 1. Using the included hex wrench, loosen the two hex screws (Fig. 8 - 1) from the bottom of the tool by turning them counterclockwise. 1 2. Pull back the base plate to disengage the angle lock pin. Fig. 8 3.
OPERATION WARNING: To prevent serious injury, make sure all the instructions have been read and understood before operating this tool. Check that the power switch works properly before plugging the tool into the power supply. WARNING: Wear safety goggles at all times that comply with ANSI Z87.1. Use ear protection such as plugs or muffs during extended periods of operation. Wear work gloves to protect your hands. Wear a face mask or dust mask to fight the dust. TURNING THE TOOL ON/OFF (Fig.
MAINTENANCE WARNING: To avoid accidents, always disconnect the tool from the power supply before cleaning or performing any maintenance. CLEANING 1. Clean the tool after every use with a soft cloth. Keep the ventilation openings free from dust and debris. Avoid using solvents when cleaning plastic parts. Most plastics are susceptible to damage from various types of commercial solvents and may be damaged by their use. 2. Remove the saw blade after use and wipe it clean with a dry cloth.
LIMITED TWO YEAR WARRANTY WEN Products is committed to build tools that are dependable for years. Our warranties are consistent with this commitment and our dedication to quality. LIMITED WARRANTY OF WEN CONSUMER POWER TOOLS PRODUCTS FOR HOME USE GREAT LAKES TECHNOLOGIES, LLC (“Seller”) warrants to the original purchaser only, that all WEN consumer power tools will be free from defects in material or workmanship for a period of two (2) years from date of purchase.
55 EXPLODED VIEW & PARTS LIST 16
EXPLODED VIEW & PARTS LIST No. 1 2 3 Part No. 33606-001 33606-002 33606-003 Description Laser Button Laser Assembly Steel Wire Protection Qty.
THANKS FOR REMEMBERING
