WOODWORKING DUST COLLECTOR FM300 184841 Model # 3403 For replacement parts visit WENPRODUCTS.COM bit.ly/wenvideo IMPORTANT: Your new tool has been engineered and manufactured to WEN’s highest standards for dependability, ease of operation, and operator safety. When properly cared for, this product will supply you years of rugged, trouble-free performance. Pay close attention to the rules for safe operation, warnings, and cautions.
TABLE OF CONTENTS Technical Data General Safety Rules Specific Safety Rules for Dust Collectors Electrical Information Unpacking Assembly Operation Maintenance Parts List & Exploded View Warranty 2 3 4 5 6 7 10 11 12 14 TECHNICAL DATA Model Number: Motor: Motor Speed: Impeller Diameter: Number of Inlet Holes: Inlet Hole Diameter: Air Suction Capacity: Collection Bag Capacity: Filter Bag Rating: Assembled Dimensions: Product Net Weight: 3403 120V, 60Hz, 16A, 1500W 3450 RPM 11.8 in. (300 mm) 2 4 in.
GENERAL SAFETY RULES Safety is a combination of common sense, staying alert and knowing how your item works. SAVE THESE SAFETY INSTRUCTIONS. WARNING! Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and serious injury. To avoid mistakes and serious injury, do not plug in your tool until the following steps have been read and understood. WORK AREA SAFETY 1. Keep work area clean and well lit.
GENERAL SAFETY RULES POWER TOOL USE AND CARE 1. Avoid accidental start-ups. Make sure the power switch is in the OFF position before connecting the plug to a power source or carrying the tool. 2. Check power tool for damaged parts. Check for misalignment of moving parts, jamming, breakage, improper mounting, or any other conditions that may affect the tool’s operation. Do not use the power tool if the switch does not turn ON/OFF. Any part that is damaged should be properly repaired or replaced before use.
ELECTRICAL INFORMATION POWER SUPPLY PREPARATION Before installing the machine, check the availability and proximity of the required power supply circuit. This dust collector has a rated amperage of 16A, but the starting amperage may spike up to 80A for a short moment. The tool has a built-in 25A overload protector to protect the motor. To prevent tripping your electrical circuit, the fuse rating of your circuit must be HIGHER than 25A.
UNPACKING Carefully unpack and remove all contents from the packaging. Identify all parts according to the chart below. If any part is damaged or missing, please contact our customer service at (800) 232-1195, M-F 8-5 CST or email us at techsupport@wenproducts.com. COMPONENTS A. B. C. D. E. F. G. H. 6 Hose Motor Assembly Collector Base Plate Upper Support Pole Lower Support Poles (3) 4-inch Inlet Adapter Collection Bag (clear) and 5-Micon Filter Bag (white) I. J. K. L. M. N. O.
ASSEMBLY WARNING: Do not attempt to plug in or operate your tool until the entire operator’s manual has been read and understood. Failure to do so could result in personal injury and damage to the tool. 1. ASSEMBLING THE CASTERS 2. ATTACHING THE MOTOR ASSEMBLY Fig. 1 Fig. 2 Place the base plate (D) upside down on a flat surface. Install the 4 casters in the following configuration: M6x10 Phillips screw, M6 washer, base plate, caster (J) and M6 nut.
ASSEMBLY 5. ASSEMBLING THE COLLECTOR 6. INSTALL THE UPPER SUPPORT POLE Fig. 5 Mount the collector (C) onto the two poles in the front as shown. Make sure that the side port of the collector is facing the motor assembly to prepare it for hose connection in Step 7. Secure them with M8x16 hex screws and M8 washers. 7. CONNECTING THE HOSE Fig. 6 The upper bag support pole (E) will be installed in the position overlapping the third bottom pole as shown.
ASSEMBLY 9. INSTALLING THE FILTER BAG Hang the filter bag (white) onto the hook of the upper bag support pole. Attach the bag over the top opening of the collector. Secure it with a bag clamp (O). 10. INSTALLING THE COLLECTION BAG Attach the plastic collection bag over the bottom opening of the collector around the rubber strip. Bag clips are located around the collector to assist in holding up the collection bag.
OPERATION WARNING: To prevent serious injury, make sure all the warnings and instructions have been read and understood before operating this tool. WARNING: Wear appropriate respirator or dust mask and safety glasses when operating the machine. Small dust particles can escape from the filter bag, causing them to become airborne and easily inhaled. This microscopic airborne dust is extremely unhealthy to breathe and can cause health problems. 1.
MAINTENANCE WARNING: Always ensure that the tool is switched off and the plug is removed from the outlet before making any cleaning, adjustments or maintenance procedures. Servicing of the tool must be performed by a qualified technician. 1. Before each use, inspect the general condition of the tool. Check for: • Loose hardware, • Misalignment or binding of moving parts, • Damaged cord/electrical wiring, • Cracked or broken parts, and • Any other condition that may affect its safe operation. 1.
EXPLODED VIEW AND PARTS LIST 12
EXPLODED VIEW AND PARTS LIST No. Parts No. Description Qty. No. Parts No. Description Qty.
LIMITED TWO YEAR WARRANTY WEN Products is committed to building tools that are dependable for years. Our warranties are consistent with this commitment and our dedication to quality. LIMITED WARRANTY OF WEN CONSUMER POWER TOOLS PRODUCTS FOR HOME USE GREAT LAKES TECHNOLOGIES, LLC (“Seller”) warrants to the original purchaser only, that all WEN consumer power tools will be free from defects in material or workmanship for a period of two (2) years from date of purchase.
THANKS FOR REMEMBERING
