VARIABLE SPEED JIG SAW For replacement parts visit Model # 3602 bit.ly/wenvideo WENPRODUCTS.COM IMPORTANT: Your new tool has been engineered and manufactured to WEN’s highest standards for dependability, ease of operation, and operator safety. When properly cared for, this product will supply you years of rugged, trouble-free performance. Pay close attention to the rules for safe operation, warnings, and cautions.
TABLE OF CONTENTS Technical Data General Safety Rules Specific Safety Rules For Jig Saw Electrical Information Know Your Jig Saw Assembly and Adjustments Operation Maintenance Exploded View and Parts List Warranty 2 3 4 5 6 7 9 10 11 13 TECHNICAL DATA Model Number: Motor: Speed: Cutting Wood Capacity: Cutting Metal Capacity: Weight: Includes: 2 3602 120 V, 60 Hz, 6A 800 - 3,000 RPM 4 in. 3/8 in. 5.
GENERAL SAFETY RULES Safety is a combination of common sense, staying alert and knowing how your item works. SAVE THESE SAFETY INSTRUCTIONS. WARNING: To avoid mistakes and serious injury, do not plug in your tool until the following steps have been read and understood. 1. READ and become familiar with this entire instruction manual. LEARN the tool’s applications, limitations, and possible hazards. 2. AVOID DANGEROUS CONDITIONS. Do not use power tools in wet or damp areas or expose them to rain.
GENERAL SAFETY RULES 15. DO NOT OVERREACH. Keep proper footing and balance at all times. Wear oil-resistant rubber-soled footwear. Keep the floor clear of oil, scrap, and other debris. 16. MAINTAIN TOOLS PROPERLY. ALWAYS keep tools clean and in good working order. Follow instructions for lubricating and changing accessories. 17. CHECK FOR DAMAGED PARTS. Check for alignment of moving parts, jamming, breakage, improper mounting, or any other conditions that may affect the tool’s operation.
SPECIFIC RULES FOR JIG SAW 8. After changing blades, rotate the blade cylinder (cutter drum) to make sure the blades don’t hit any part of the blade head housing and that the blade locking screws are tight. Loose or misaligned blades have the potential to strike tool housing and damage the tool as well as cause possible injury. 9. Always hold the tool firmly with both hands for maximum control. 10. Never pull the jig saw backwards over the workpiece. 11.
ELECTRICAL INFORMATION WARNING: This tool is for indoor use only. Do not expose to rain or use in damp locations. Guidelines for using extension cords Make sure your extension cord is in good condition. When using an extension cord, be sure to use one heavy enough to carry the current your product will draw. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating. The table below shows the correct size to be used according to cord length and nameplate ampere rating.
ASSEMBLY AND ADJUSTMENTS REMOVING OR INSTALLING JIG SAW BLADE WARNING: To avoid injury from accidental startups, turn switch OFF and remove the plug from the power source outlet before making any adjustments. WARNING: These blade cannot and should not be re-sharpened. WARNING: The jig saw blade is sharp and fragile and must be handled carefully to avoid injury to the user and damage to the blade. Do not attempt to sharpen or use resharpened blades of any kind.
ASSEMBLY AND ADJUSTMENTS ADJUSTING THE FOOTPLATE FOR BEVEL CUTS The footplate can be set to make either a straight cut or a left or right bevel cut at an angle of 45°. 1. Loosen the two screws on the underside of the base plate (1) until the base plate slides back and forth. 2. Pull the footplate forward to disengage the angle lock pin. Slide the shoe to the left or right and push it back into the 15°, 30° and 45° location. The angle will appear on the side of the base plate. 3. Tighten the two screws (1).
OPERATION PLUNGER SPEED The required cutting speed or stroke rate depends on the material being cut, the type of blade being used, and the feed rate preferred by the operator. The best speed for a particular application is largely determined by experience though as a general rule, slower speeds are for denser materials and faster speeds for softer materials.
MAINTENANCE SERVICE: Preventive maintenance performed by unauthorized personnel may result in misplacing of internal wires and components, possibly causing a serious hazard. We recommend that all tool service be performed by a WEN Service Center or Authorized WEN Service Station. TOOL LUBRICATION: Your tool has been properly lubricated and is ready to use. It is recommended that tools with gears be regreased with a special gear lubricant at every brush change.
EXPLODED VIEW AND PARTS LIST 11
EXPLODED VIEW AND PARTS LIST Item 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 18 19 20 21 22 23 24 25 26 27 12 Stock # 3602-001 3602-002 3602-003 3602-004 3602-005 3602-006 3602-007 3602-008 3602-009 3602-010 3602-011 3602-012 3602-013 3602-014 3602-015 3602-016 3602-018 3602-019 3602-020 3602-021 3602-022 3602-023 3602-024 3602-025 3602-026 3602-027 Description Screw Dust tube O-ring Right housing Brush holder Brush carrier Brush Bearing Label clip Switch Cable Cable guard Left housing Left housing coat Spe
LIMITED TWO YEAR WARRANTY WEN Products is committed to building tools that are dependable for years. Our warranties are consistent with this commitment and our dedication to quality. LIMITED WARRANTY OF WEN CONSUMER POWER TOOLS PRODUCTS FOR HOME USE GREAT LAKES TECHNOLOGIES, LLC (“Seller”) warrants to the original purchaser only, that all WEN consumer power tools will be free from defects in material or workmanship for a period of two (2) years from date of purchase.
Thanks for remembering
