RECIPROCATING SAW For replacement parts visit Model # 3630 bit.ly/wenvideo WENPRODUCTS.COM IMPORTANT: Your new tool has been engineered and manufactured to WEN’s highest standards for dependability, ease of operation, and operator safety. When properly cared for, this product will supply you years of rugged, trouble-free performance. Pay close attention to the rules for safe operation, warnings, and cautions.
TABLE OF CONTENTS 2 3 4 5 6 7 7 8 9 10 Technical Data General Safety Rules Specific Safety Rules For Reciprocating Saws Electrical Information Know Your Reciprocating Saw Assembly and Adjustments Operation Maintenance Exploded View and Parts List Warranty TECHNICAL DATA Model Number: Motor: Speed: Stroke: Cutting Wood Capacity: Cutting Metal Capacity: Weight: Includes: 2 3630 120 V, 60 Hz, 10A 0 - 2,800 RPM 1-1/10 in. 4-1/2 in. 3/5 in. 7.
GENERAL SAFETY RULES Safety is a combination of common sense, staying alert and knowing how your item works. SAVE THESE SAFETY INSTRUCTIONS. WARNING: To avoid mistakes and serious injury, do not plug in your tool until the following steps have been read and understood. 1. READ and become familiar with this entire instruction manual. LEARN the tool’s applications, limitations, and possible hazards. 2. AVOID DANGEROUS CONDITIONS. Do not use power tools in wet or damp areas or expose them to rain.
GENERAL SAFETY RULES 15. DO NOT OVERREACH. Keep proper footing and balance at all times. Wear oil-resistant rubber-soled footwear. Keep the floor clear of oil, scrap, and other debris. 16. MAINTAIN TOOLS PROPERLY. ALWAYS keep tools clean and in good working order. Follow instructions for lubricating and changing accessories. 17. CHECK FOR DAMAGED PARTS. Check for alignment of moving parts, jamming, breakage, improper mounting, or any other conditions that may affect the tool’s operation.
SPECIFIC RULES FOR RECIPROCATING SAWS 9. Never cut pressurized tanks or any containers containing hazardous or flammable materials. 10. Never pull the saw backwards over the workpiece. 11. When sawing, the adjustable footplate must always stay flush against the workpiece. 12. Remove the plug from power source before removing chips. The blades are hidden from view and you may be cut if the blade is contacted. 13.
ELECTRICAL INFORMATION GUIDELINES FOR USING EXTENSION CORDS Make sure your extension cord is in good condition. When using an extension cord, be sure to use one heavy enough to carry the current your product will draw. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating. The table below shows the correct size to be used according to cord length and nameplate ampere rating. When in doubt, use a heavier cord. The smaller the gauge number, the heavier the cord.
ASSEMBLY WARNING: Never make any adjustments or blade installations while the machine is plugged in. Make sure that saw blades are free of fine material, such as small slivers of metal or wood. Use protective gloves during operation and assembly. REPLACING/INSTALLING SAW BLADES 1. Select a saw blade with a 1/2-inch universal shank. If narrow curve cuts are required, a thinner blade would be preferable. Saw blades should never be longer than is required for the intended cut. 2.
OPERATION VARIBALE PRESSURE TRIGGER Control the strokes per minute of the saw by varying the amount of pressure applied to the trigger. Holding the trigger all the way down will result in 2800 SPM. Ligher pressure on the ON/OFF trigger will result in a lower SPM. WORK ADVICE NOTE: When sawing lighter materials, make sure to keep in mind the recommendations of the material suppliers. Check all workpieces for foriegn objects usch as nails or screws before sawing.
EXPLODED VIEW AND PARTS LIST No.
LIMITED TWO YEAR WARRANTY WEN Products is committed to building tools that are dependable for years. Our warranties are consistent with this commitment and our dedication to quality. LIMITED WARRANTY OF WEN CONSUMER POWER TOOLS PRODUCTS FOR HOME USE GREAT LAKES TECHNOLOGIES, LLC (“Seller”) warrants to the original purchaser only, that all WEN consumer power tools will be free from defects in material or workmanship for a period of two (2) years from date of purchase.