3-1/4" MINI CIRCULAR SAW 3087464 Model # 36703 For replacement parts visit WENPRODUCTS.COM bit.ly/wenvideo IMPORTANT: Your new tool has been engineered and manufactured to WEN’s highest standards for dependability, ease of operation, and operator safety. When properly cared for, this product will supply you years of rugged, trouble-free performance. Pay close attention to the rules for safe operation, warnings, and cautions.
TABLE OF CONTENTS Technical Data Safety Introduction General Safety Rules Rules for the Mini Circular Saw Electrical Information Know Your Mini Circular Saw Assembly & Adjustments Operation Maintenance Warranty Statement Exploded View and Parts List 2 3 4 6 8 9 10 13 14 15 16 TECHNICAL DATA Model Number: 36703 Motor: AC 120V, 60Hz, 4.2A No-Load Speed: 4500 RPM Maximum Cutting Depth: 63/64 in. (25 mm) Blade Size: 3-1/4 in. (85 mm) Arbor Size: 3/8 in.
SAFETY INTRODUCTION Thanks for purchasing the WEN Mini Circular Saw. We know you are excited to start sawing through your workpiece, but first, please take a moment to read through the manual. This manual provides information regarding potential safety concerns, as well as helpful assembly and operating instructions. Safe operation of this tool requires that you read and understand this operator’s manual and all labels affixed to the tool.
GENERAL SAFETY RULES Safety is a combination of common sense, staying alert and knowing how your item works. SAVE THESE SAFETY INSTRUCTIONS. WARNING! Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and serious injury. To avoid mistakes and serious injury, do not plug in your tool until the following steps have been read and understood. WORK AREA SAFETY 1. Keep work area clean and well lit.
GENERAL SAFETY RULES POWER TOOL USE AND CARE 1. Avoid accidental start-ups. Make sure the power switch is in the OFF position before connecting the plug to a power source or carrying the tool. 2. Check power tool for damaged parts. Check for misalignment of moving parts, jamming, breakage, improper mounting, or any other conditions that may affect the tool’s operation. Do not use the power tool if the switch does not turn ON/OFF. Any part that is damaged should be properly repaired or replaced before use.
RULES FOR THE MINI CIRCULAR SAW WARNING: Do not let comfort or familiarity with the product replace strict adherence to product safety rules. If you use this tool unsafe or incorrectly, you can suffer serious personal injury. 1. WORK ENVIRONMENT. Do not operate the tool in wet or damp conditions; doing so significantly increases the risk of electrical shock. Do not operate the tool in the presence of flammable liquids or gases. 2. PERSONAL SAFETY. Always wear ANSI Z87.
RULES FOR THE MINI CIRCULAR SAW REDUCING KICKBACK Kickback is a sudden reaction to a pinched, bound or misaligned saw blade, causing an uncontrolled saw to lift up and out of the work piece toward the operator. When the blade is pinched or bound tightly by the kerf closing down, the blade stalls and the motor reaction drives the unit rapidly back toward the operator.
ELECTRICAL INFORMATION FOR ALL DOUBLE-INSULATED TOOLS Double insulation is a concept in safety in electric power tools, where two systems of insulation are provided. This eliminates the need for the usual three-wire grounded power cord. All exposed metal parts are isolated from the internal metal motor components with protecting insulation. Double insulated tools do not need to be grounded.
KNOW YOUR MINI CIRCULAR SAW Carefully unpack the tool from the packaging. Check all components and compare against the graph below. If any part is damaged or missing, please contact our customer service at (800) 232-1195, M-F 8-5 CST or email us at techsupport@wenproducts.com.
ASSEMBLY & ADJUSTMENTS WARNING: To avoid injury from accidental startups, be sure that the tool is switched off and disconnected from the power supply before inspecting the unit, making adjustments or changing accessories. SELECT THE RIGHT BLADE Your mini circular saw is a versatile tool that is capable of cutting different materials by using the correct blade. Your tool comes with three blades: a wood-cutting blade (pre-installed), a metal-cutting blade and a tile-cutting blade.
ASSEMBLY & ADJUSTMENTS SETTING THE DEPTH OF CUT (Fig. 1 & 2) Before making a cut, it is important to set the correct cutting depth. The saw’s maximum cutting depth is 63/64 inch (25 mm). We recommend adjusting the cutting depth about 1/16 inch (2 mm) deeper than the thickness of the material. To adjust the cutting depth, you can either reference the depth scale, or the edge of the workpiece. Using the Depth Scale: 1. Disconnect your saw from the power source. Depth Lock Lever 2.
ASSEMBLY & ADJUSTMENTS INSTALLING THE RIP FENCE When making a rip cut along a straight edge, it is recommended to clamp a straight edge to the workpiece or use the included rip fence. To install the rip fence onto your saw: 1. Loosen the fence lock knob on the front of the base plate. Fence Lock Knob 2. Insert the rip fence from the left side of the tool through all three slots on the base plate. 3. Adjust the rip fence to the desired width of cut indicated by the cutting guide indicator. 4.
OPERATION WARNING: To prevent serious injury, make sure all the instructions have been read and understood before operating this tool. Check that the power switch mechanisum works properly before plugging the tool into the power supply. OPERATING THE SAW 1. Hold the tool firmly in your right hand with your thumb on the blade release switch and your fingers in the grooves of the power switch. Stand to the left side of the saw. 2. Set the front portion of the base plate onto the workpiece.
MAINTENANCE WARNING: To avoid accidents, always disconnect the tool from the power supply before cleaning or performing any maintenance. 1. Clean the tool after every use with a soft cloth or low-pressure compressed air. Do not let water enter the tool. 2. Keep the ventilation openings free from dust and debris to prevent the motor from overheating. 3. Do not use any solvents or cleaning products that could damage the plastic parts.
LIMITED TWO YEAR WARRANTY WEN Products is committed to build tools that are dependable for years. Our warranties are consistent with this commitment and our dedication to quality. LIMITED WARRANTY OF WEN CONSUMER POWER TOOLS PRODUCTS FOR HOME USE GREAT LAKES TECHNOLOGIES, LLC (“Seller”) warrants to the original purchaser only, that all WEN consumer power tools will be free from defects in material or workmanship for a period of two (2) years from date of purchase.
. . . .
EXPLODED VIEW & PARTS LIST No. 1 2 3 4 5 6 7 8 9.1 9.2 Part No. 36703-001 36703-002 36703-003 36703-004 36703-005 36703-006 36703-007 36703-008 36703-009.1 36703-009.2 10 36703-010 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30.1 30.2 31 32 33 34 35 36 37 38 39 40 41 36703-011 36703-012 36703-013 36703-014 36703-015 36703-016 36703-017 36703-018 36703-019 36703-020 36703-021 36703-022 36703-023 36703-024 36703-025 36703-026 36703-027 36703-028 36703-029 36703-030.1 36703-030.
THANKS FOR REMEMBERING
