0-INCH WET/DRY SHARPENER Model # 4270 bit.ly/wenvideo IMPORTANT: Your new tool has been engineered and manufactured to WEN’s highest standards for dependability, ease of operation, and operator safety. When properly cared for, this product will supply you years of rugged, trouble-free performance. Pay close attention to the rules for safe operation, warnings, and cautions. If you use your tool properly and for intended purpose, you will enjoy years of safe, reliable service.
TABLE OF CONTENTS 2 3 4 6 7 8 10 11 12 14 Technical Data General Safety Rules Specific Safety Rules For Sharpener Electrical Information Know Your Sharpener Operation Maintenance Troubleshooting Exploded View and Parts List Warranty TECHNICAL DATA Model Number: Motor: Wheel Speed: Wet Wheel Diameter: Wet Wheel Grit: Leather Stropping Wheel Diameter: Net Weight: Product Dimensions: 2 4270 120V, 60 Hz, 1.6A 115 RPM 10 inches 220 grit 8 inches 36 pounds 16.9 x 10.8 x 16.
GENERAL SAFETY RULES Safety is a combination of common sense, staying alert and knowing how your item works. SAVE THESE SAFETY INSTRUCTIONS. WARNING: To avoid mistakes and serious injury, do not plug in your tool until the following steps have been read and understood. 1. READ and become familiar with this entire instruction manual. LEARN the tool’s applications, limitations, and possible hazards. 2. AVOID DANGEROUS CONDITIONS. Do not use power tools in wet or damp areas or expose them to rain.
GENERAL SAFETY RULES 15. DO NOT OVERREACH. Keep proper footing and balance at all times. Wear oil-resistant rubber-soled footwear. Keep the floor clear of oil, scrap, and other debris. 16. MAINTAIN TOOLS PROPERLY. ALWAYS keep tools clean and in good working order. Follow instructions for lubricating and changing accessories. 17. CHECK FOR DAMAGED PARTS. Check for alignment of moving parts, jamming, breakage, improper mounting, or any other conditions that may affect the tool’s operation.
SPECIFIC RULES FOR THE SHARPENER 11.. Do not use in damp conditions. Do not expose to rain. 12. Only use accessories that are recommended by WEN for this model. 13. Only use grinding wheels rated for a speed higher than the maximum RPM of the tool. 14. Never attempt to cut anything with the grinding wheel. 15. Do not use a wheel that vibrates. Make sure grinding wheels are dressed properly. If a wheel vibrates, it may be that the bearings of the shaft need replacing also.
ELECTRICAL INFORMATION GROUNDING INSTRUCTIONS IN THE EVENT OF A MALFUNCTION OR BREAKDOWN, grounding provides the path of least resistance for an electric current and reduces the risk of electric shock. This tool is equipped with an electric cord that has an equipment grounding conductor and a grounding plug. The plug MUST be plugged into a matching outlet that is properly installed and grounded in accordance with ALL local codes and ordinances. DO NOT MODIFY THE PLUG PROVIDED.
KNOW YOUR SHARPENER C B KNOW YOUR SHARPENER A - Grinding Wheel B - Universal Jig/Work Support C - Knife Holding Jig D - Horizontal Mount (Back) E - Vertical Mount (Front) F - Leather Stropping Wheel G - Power Switch H - Water Reservoir H D E F A G UNPACKING WARNING: To avoid injury from accidental startups, turn switch OFF and remove the plug from the power source outlet before making any adjustments. Carefully unpack the sharpener and all its parts, and compare against the list below.
OPERATION GRINDING TIPS Make sure the grinding wheel’s water reservoir has been adequately filled. Wear the proper safety clothes including but not limited to safety goggles and a dust mask. Grasp the workpiece firmly, making sure it is properly supported by either the universal jig or the work support. Apply pressure evenly during grinding operations. When grinding, metal objects become heated quickly. Always move the object back and forth to prevent overheating.
OPERATION WATER RESERVOIR This sharpener has been designed for wet grinding only. NEVER USE THE GRINDING WHEEL WITHOUT WATER. Note that there are multiple slots on either side of the unit. The lower most slot is to be used when the grinding wheel is at a full 10 inches. Once the grinding wheel has been worn down to roughly 8 inches, the higher slots should be used. Fill up the container to the “Max Water Level” line signified on the inside of the reservoir.
MAINTENANCE WARNING: For your own safety, turn the switch OFF and remove the plug from the electrical outlet before adjusting or performing maintenance or lubrication work on the sharpener. Before using, check to make sure parts are not damaged, missing, or worn. Check for alignment of moving parts, binding of moving parts, improper mounting, or any other conditions that may affect the sharpener’s operation.
TROUBLESHOOTING PROBLEM CAUSE The dang motor 1) Low voltage won’t start. 2) Loose connections or open circuit in the motor. 3) Blown fuse/breaker. SOLUTION 1) Make sure the power source is providing the proper voltage. 2) Inspect the motor for loose or open connections. Send for servicing if found. 3) Replace the fuse or reset the breaker The motor is 1) Overloaded motor 1) Reduce load on the motor. getting way too 2) Extension cord too long or not thick 2) Utilize an extension cord with an approprihot.
EXPLODED VIEW AND PARTS LIST ITEM 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 12 PART.
EXPLODED VIEW AND PARTS LIST 13
LIMITED TWO YEAR WARRANTY WEN Products is committed to building tools that are dependable for years. Our warranties are consistent with this commitment and our dedication to quality. LIMITED WARRANTY OF WEN CONSUMER POWER TOOLS PRODUCTS FOR HOME USE GREAT LAKES TECHNOLOGIES, LLC (“Seller”) warrants to the original purchaser only, that all WEN consumer power tools will be free from defects in material or workmanship for a period of two (2) years from date of purchase.
